Instruction/ maintenance manual of the product V3 Antec
Go to page of 15
N INE H UNDRE D T WO V 3 U SER ’ S M ANUAL.
1 Table of C ontents Introduction 1.1 Case Specifications ............ ............ .................... ............ ............ ....................... .. 3 1.2 Diagram ............ ............ ............ ..................... ............ .....
2 Congratula tions on yo ur purchase of the N ine Hund red Two V3! The best-selling Antec Nine Hu ndred offers gamers an un beatable enclosure, one that delivers a combination of cooling, performance and con venience and stands head and shoulders above the competition.
3 1.1 Case Specific ations Case Type Mid Tower Color Black Dimensions 19.3” (H) x 8.7” (W) x 18.5” (D) 493 mm (H) x 218 mm (W) x 472 m m (D) Weight 25.
4 Hardware I nstall ation Guide 2.1 Setting Up 1. Place the case upright on a flat, stable surface so that the rear panel (po wer supply and expansion slots) is facing you. 2. Remove the panel thumbscrews from the side pan el and open it by sliding it tow ards you.
5 4. Lift up and remove the moth erboard. 5. Screw in the brass standoffs to the threaded holes that line up with the motherboard. 6. Place the motherboard on the brass stand offs. Screw in the motherboard to the stand offs with the provided Phillips-head screws.
6 7. There is a 120 mm fan pre-installed int o each cage. Connect the 4-pin connector to the p ower supply. Note : There is a middle fa n bracket pre-installed on one of the HDD cages. Remove it from the cage if you decide to mount your hard drives into this cage.
7 2.8 I nternal 2.5” Device Installation At the bottom of your case, there are mounting holes designed to support on e 2.5” SSD device. 1. Locate the plastic bag labeled “For 2.5 HDD” and remove the 4 silicone grommets. 2. Install the grommets into the four holes at the base of the case at the bottom of the drive bay area as shown.
8 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative S ignal 1 4 Negative S ignal 2 5 Positive S ignal 1 6 Positive S ignal 2 7 Ground 1 8 Ground 2 9 Key (No Connection) 10 Empty Pin 2.10 Water Cooli ng Platform This case comes with a 5.
9 Pin Sig nal Nam es (HDA) Pin Sig nal Nam es (A C’9 7) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Po wer 4 AV CC 4 N C 5 FRO- R 5 Lin e Ou t (R) 6 MIC2 _ JD 6 Lin e Ou t (R) 7 F_I O_ SEN 7 N C 8 Key (no pin ) 8 Key (no pin ) 9 FRO-L 9 Lin e Ou t (L) 10 LINE2 _JD 10 Lin e Ou t (L) 3.
10 3.5 Rewirin g Motherboard Header Connection s There may come a time that you need t o reconfigure the pin-out of a motherb oard header connector. Examples could be for your USB header, audio input h eader, or some other front pan el connector such as the Power Button connector.
11 Size: 200 x 30 mm three-speed fan Rated Voltage: 12V DC Operating Voltage: 10.8V ~ 13.2V Speed (RPM) Input Current Air Flow Static Pressure Acoustic Noise Input Power High 800 0.3A 3.8 m³ / min (134 CFM) 0.7mm-H2O (0.03 inch- H2O) 30 dBA 3.6 W Medium 600 0.
12 Size: 120 x 25 mm TriCool™ fan Rated Voltage: 12V Operating Voltage: 10.2V - 13.8V S p e e d ( R P M ) I n p u t C u r r e n t A i r F l o w S t a t i c P r e s s u r e A c o u s t i c N o i s e I n p u t P o w e r H i g h 2000 0 . 2 4 A ( M a x .
13 the holes in the fan are secu red to the mount. 3. Use the long screws provided to secure th e fan to the mount. Do not overtighten. 4. Run the power (and control switch if using a TriCool™ fan) through the cable guide that runs along the sid e of the mount.
14 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canad a 1-800-22ANTEC customersupport@antec.
An important point after buying a device Antec V3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Antec V3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Antec V3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Antec V3 you will learn all the available features of the product, as well as information on its operation. The information that you get Antec V3 will certainly help you make a decision on the purchase.
If you already are a holder of Antec V3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Antec V3.
However, one of the most important roles played by the user manual is to help in solving problems with Antec V3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Antec V3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
