Instruction/ maintenance manual of the product Skeleton Antec
Go to page of 14
SKELETON User’s Manual.
Table of Contents Introduction 1.1 Case Specifications………………...……………......…………… 2 1.2 Diagram……………………………………………....…......……… 2 1.3 How to Carry the Skeleton…………………………….
1 At Antec, we continually refine and improve our products to ensure the highest quality. As such, it’s possible that your new case may differ slightly from the description in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct.
2 1.1 Case Specifications Case Type Open Case Design Color Metallic Silver Dimensions 13”(H) x 14.8”(W) x 16.5”(D) 33.02 (H) x 37.6 cm (W) x 41.9 cm (D) Weight 15.5 lbs / 7 kg Cooling 1 x Super Big Boy 250mm Multi-LED Fan 1 x 92mm Hard Drives Fan Drive Bays 2 x Quick Release 5.
3 1.3 How to Carry the Skeleton The Skeleton case is designed to be held by either set of grips on the top of the side railing. Use these handles when moving or transporting your case. Do not carry the case by the plastic PCI holder, as it was not designed to be a load-bearing device.
4 2. To completely remove the Component Tray from the Frame, find the release tab on the lower left side of the Component Tray when the Tray is fully extended. Press it upwards, then pull the Tray out and completely free of the Frame. 3. To replace the Component Tray in the Frame, align the Tray with the back of the case, and slide it forward.
5 3. Place the motherboard on the brass standoffs. Screw in the motherboard to the standoffs with the provided Phillips-head screws. Replace the Motherboard Tray onto the Component Tray, and the Component Tray in the Frame as detailed in sections 2.1 and 2.
6 3. Slide the plate-mounted power supply into the bottom level of the Component Tray until it locks into position. There are two possible locations to mount the power supply, depending on the size of your equipment. Note : Power supplies equipped with an 80mm fan will draw air through the Skeleton and power supply more effectively.
7 4. Connect the data and power connectors from the motherboard and power supply to the device. Note : It may be necessary to remove the motherboard tray and/or side screens as detailed in sections 2.2 and 2.3 to effectively route cables to your devices.
8 Connecting the Front I/O Port s 3.1 USB 2.0 Ports Connect the front I/O panel USB cable to the USB header pin on your mother- board. Check the motherboard manual to ensure that it matches the table below: Motherboard USB Pin Layout Locate the internal USB connector on your motherboard and connect the corresponding cable.
9 3.4 AC’97/HD Audio Ports Connected to your front I/O panel there is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector.
10 Cooling System 4.1 The Super Big Boy 250mm Multi-LED Fan The Skeleton’s unique and innovative open case design provides that only one Super Big Boy 250mm Multi-LED fan is required to cool most of your system components. This overhead fan is adjustable, allowing you to choose the best speed suited to your needs.
11 4.3 Removing the 92 mm Hard Drive Fan Ensure that the fan power cable is disconnected before removing the fan. 1. While facing the front of the case, depress the two tabs on the top of the 92mm fan and detach it from the front of the hard drive housing.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.
An important point after buying a device Antec Skeleton (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Antec Skeleton yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Antec Skeleton - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Antec Skeleton you will learn all the available features of the product, as well as information on its operation. The information that you get Antec Skeleton will certainly help you make a decision on the purchase.
If you already are a holder of Antec Skeleton, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Antec Skeleton.
However, one of the most important roles played by the user manual is to help in solving problems with Antec Skeleton. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Antec Skeleton along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
