Instruction/ maintenance manual of the product P190 Antec
Go to page of 10
P190 User’s Manual Manuel de l’utilisateur Anwenderhandbuch Manuale per l’operatore Manual del usuario পᡅ䂀ᯢ.
1 At Antec, we continually refine and improve our products to ensure the highest quality. As such, it’s possible that your new case may differ slightly from the description in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct.
2 a tool box attached to the upper HDD cage containing more hardware (screws, brass standoffs, spare silicone grommets, etc.). Cable Management You can route data and power supply cables through the holes behind the motherboard (MB) tray. 1. Remove both side panels.
3 will allow you to connect the front USB to your motherboard on a pin-by-pin basis. Motherboard USB Pin Layout Connecting the IEEE 1394 (FireWire®, i.Link®) Port You will find a single 10-pin connector on a cable attached to the front IEEE 1394 connection.
4 Pin Assignment for Audio Ports (HDA and AC’97) Locate the internal audio connectors from your motherboard or sound card. Consult your motherboard or sound card manual for the pin-out positions. 3.5” Device Installation With the front bezel facing you, swing the front door out.
5 noise-dampening ability of the rubber grommets. Always mount the HDD with the thicker side of the silicone grommets facing up. 5. Repeat the same procedure for other devices as necessary. 6. Connect 4-pin molex or SATA power connectors on the power supply to the power connectors on each of the devices.
6 or Low to a fan-control device may result in the fan not being able to start. The already lowered voltage from the fan controller will be further reduced by the TriCool™ circuitry below 5V. The Top and Rear Exhaust TriCool™ Fans The case comes with two 140mm top and one 120mm rear exhaust TriCool™ fans.
7 200mm Big Boy™ Specifications: Size: 200 x 200 x 30mm Big Boy™ Fan Rated Voltage: DC 12V Operating Voltage: 10.2V ~ 13.8V The Optional Fans There are two optional 120mm fan mounts – a front fan (in front of the upper HDD cage) and a middle fan (at the rear end of the upper HDD cage).
8 To remove the front filters: 1. Push one of the fan grilles at the right middle edge to open the grille. 2. There are two tabs on the filter. To remove the filter, use both hands to gen- tly push the tabs downward. Slightly angle the top of the filter towards you before lifting it up and out.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Sydneystraat 33 3047 BP Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.
An important point after buying a device Antec P190 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Antec P190 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Antec P190 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Antec P190 you will learn all the available features of the product, as well as information on its operation. The information that you get Antec P190 will certainly help you make a decision on the purchase.
If you already are a holder of Antec P190, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Antec P190.
However, one of the most important roles played by the user manual is to help in solving problems with Antec P190. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Antec P190 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
