Instruction/ maintenance manual of the product 8573714B KitchenAid
Go to page of 20
Installation Instructions Single Drawer Dishwasher Instructions d'installation Lave-vaisselle à tiroir unique 528534/ 8573714B ® HOME APPLIANCES T able of Contents/T able des matières.
2 T able of Contents Drawer Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 T ools and Parts . . . . . . . . . . . . . . . . . . . . . . .
3 T ools needed: ■ Utility knife ■ Needle-nose pliers ■ T ape measure ■ Flat-bladed screwdriver ■ #2 Phillips screwdriver ■ Side cutting pliers ■ Pencil ■ Sandpaper ■ Level ■ Adjus.
4 Cabinet dimensions/requirements 4" (10 cm) moisture pr otection tape support surface must be solid and level Utility hole: 1 ¹⁄₂ " (3.8 cm) dia. hole, either side – immediately adjacent to corner . 22 ⁷⁄₈ " (58.0 cm) 3 ¹³⁄₁₆ " (9.
If Installing Flexible Trim Pieces If the cabinet opening is 24" wide (61.0 cm), flexible trim pieces can be attached along the sides of the dishwasher . (No trim piece used along the top.) 1. Open the drawers to expose the chassis trim . 2. Center the flexible trim pieces.
5. Open the drawer . 6. Press in the right-hand runner clip and push it back about 6 ” (15.2 cm). Repeat with the left-hand runner clip. NOTE: When removing the drawer ther e is limited range of movement due to the attached water hoses. 7. Lift the right edge of the drawer off its runner .
7 Option 2: Garbage disposal connection 1. Route the drain hose as shown and press the hose into the drain hose support. 2. Decide if the drain hose needs to be trimmed. If it does, trim it. NOTE: The drain hose connector must not support the weight of excess hose length.
8 Connect to W ater Supply 1. Install the flat seal washer on the end of the inlet hose. Connect the inlet hose to the water supply valve. Tighten securely . 2. T ur n the water valve on and check for any leaks. 3. Open the drawer . Remove the packing tape from the front and rear of dish rack.
9 6. Measure and mark the vertical centerline and horizontal position line on the back of the custom door panel. 7. Mount the handle to the custom door panel.
10 18. Line up the bracket holes with the pin holes and replace each pin so that the pin line is vertical. Complete Installation 1. Check that all parts are now installed. If ther e is an extra part, go back through the steps to see which step was skipped.
11 T able des matièr es Sécurité du lave-vaisselle tiroir . . . . . . . . . . . . . . . . . . . . . . . 11 Exigences d'installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Outillage et pièces . . . . . . . . . . . . . . .
12 Outillage nécessaire : ■ couteau utilitaire ■ pince à bec effilé ■ mètre-ruban ■ tournevis à lame plate ■ tournevis Phillips n° 2 ■ pince coupante latérale ■ crayon ■ papier .
Placard- Dimensions à r especter 13 ruban adhésif anti-humidité ruban adhésif jusqu’à ¹⁄₂ " (12,7 mm) de l’avant du plan de travail installation typique plan de travail ■ Construire le placard personnalisé aux dimensions indiquées et en respectant les instructions fournies.
14 L ’appareil doit êtr e alimenté uniquement par un circuit de 120 V CA (60 Hz), protégé par fusible de 15 A (disjoncteur ou fusible temporisé de préférence). Il est r ecommandé que l’appareil soit alimenté par un circuit indépendant. INSTRUCTIONS D'INST ALLA TION Préparation de la cavité d’installation 1.
15 3. Déployer complètement l'une des glissières du tir oir . Vérifier que les loquets à l'arrière de chaque glissièr e du tiroir sont orientés vers l'avant.
2. Déterminer s’il est nécessaire de tailler les segments du tuyau d'évacuation. Effectuer maintenant ces opérations si nécessaire. NOTE : Le connecteur de tuyau de vidange ne doit pas soutenir le poids d'une longueur de tuyau excessive.
17 Option 2 : Connexion sur le broyeur à déchets 1. Acheminer le tuyau d’évacuation comme l’indique l’illustration ci-dessous. Placer les tuyaux sur les supports. 2. Déterminer s’il est nécessaire de tailler les segments du tuyau d’évacuation.
18 1. Préparer le panneau avant personnalisé conformément aux spécifications. La largeur des panneaux peut êtr e supérieure à celle du lave-vaisselle, pour un meilleur ajustement avec les placards adjacents. 2. Mesurer et mar quer l'emplacement de la poignée fournie par le client sur l'avant du panneau personnalisé.
19 6. Sur la surface arrière du panneau avant, mesur er et tracer les lignes de positionnement verticale et horizontale. 7. Monter la poignée sur le panneau personnalisé. Les vis ne doivent pas traverser la face arrière du panneau. Fraiser les trous.
Benton Harbor , Michigan 49022 Printed in New Zealand Imprimé en Nouvelle-Zélande 03/2006 8573714B © 2006 KitchenAid ® Marque déposée/™ Mar que de commerce de KitchenAid, U.
An important point after buying a device KitchenAid 8573714B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought KitchenAid 8573714B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data KitchenAid 8573714B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, KitchenAid 8573714B you will learn all the available features of the product, as well as information on its operation. The information that you get KitchenAid 8573714B will certainly help you make a decision on the purchase.
If you already are a holder of KitchenAid 8573714B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime KitchenAid 8573714B.
However, one of the most important roles played by the user manual is to help in solving problems with KitchenAid 8573714B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device KitchenAid 8573714B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
