Instruction/ maintenance manual of the product 1435 KitchenAid
Go to page of 16
- Installation Instructions 30” Built-In Microwave Convection Hood L IMPORTANT: Installer: Leave Installation Instructions with the Homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use.
30” BUILT-IN MICRO WAVE /HOOD MODEL KHMC106 W INSTALLATION INSTRUCTIONS CONTENTS: Introduction ....................................................................... 1 Mounting Space .................................................................
INTRODUCTION Proper installation is the installer’s responsibility. A qualified technician should install this microwave oven. Make sure you have everything necessan/ for correct installation. It is the responsibility of the installer to comply with the installation clearances specified on the serial/rating plate.
WALL CONSTRUCTION Personal Injury or Property Damage Hazard l This microwave oven must be mounted against and supported by a flat, vertical wall. l This microwave oven must be attached with two lag screws to a minimum of one, vertical 2” x 4” wall stud.
ELECTRICAL REQUIREMENTS Electrical ground is required on this appliance. E-&~&Hazard l Checkwithaqualifiedelectricianifyouareindoubtastowhethertheapplianceisp~perlygrounded. Improper connection of the equipment-grounding conductor can result in electrical shock.
HOOD EXHAUST DUCT When the hood is vented to the outside, a HOOD EXHAUST DUCT is required. All ductwork must be metal (do not use plastic duct). Check that all connections are made securely. Please read the following carefully: Fire Hazard Mntirg system must terminate to the outside.
TOOLS RECOMMENDED FOR INSTALLATION Phillips Screwdriver Electric Drill l/2”, 5/8” and 3/32’ Drill Bits 1 -l/2’ Wood Bit or metal hole cutter (if metal cabinet is used) Saw to cut exhaust opening (if needed) Knife or single edge razor Pencil Measure Tape Protective drop cloth for product and range.
PREPARATION OF CARTON Utilization of the canon may make installation easier. CHECK THE PRODUCT FOR DAMAGE 1. Remove product and shipping pads. Visually check the product after removing from carton. Remove all packing material from inside the oven cavity.
VENTILATION SYSTEM THIS MICROWAVE OVEN/HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THREE TYPES OF HOOD VENTILATION SYSTEMS: A. Vertical Exhaust -- outside ventilation B. Horizontal Exhaust -- outside ventilation C. Recirculating -- non-vented, ductless Select the type required for your installation.
HORIZONTAL EXHAUST (Continued) 2. Withdraw hood fan unit upward carefully (Fig.4). Figure 4 1. 3. Rotate hood fan unit l/4 turn as shown in Figure5 Figure 5 4. Replace hood fan unit into the oven unit. Be careful not to pinch the lead wire between the inner bracket and the hood fan unit (Fig.
1 ,, .:y 2. -- .; . . . -A.,~*;-,-, .-. 5. Replace the fan cover bracket. Make sure the fan blades are visible through the rear openings in the cover before proceeding. Attach cover to unit with 3 screws (Fig. 7). The hood fan unit is now rotated for horizontal exhaust operation See page 11 for exhaust adaptor assembly installation instructions.
PREPARATION OF WALL AND TOP CABINET MOUNTING TEMPLATES THIS PRODUCT CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES.
5. If horizontal exhaust is used, attach the exhaust adaptor assembly to each of the mounting plates by aligning the holes on the assembly with the tabs on the plates, holding the as- sembly in place and bending the tabs to secure the assembly to the plates (Fig.
Thread the oower sunulv cord throueh the hole made at the bottom of the ton cabinet I Personal Injury Hazard Two people are required to lift this microwave. Failure to use more than one person during installation may result in oersonal iniurv. I Hang the unit on the lower edge of the mounting plates.
8. Use the two top cabinet mounting screws (C) and flat washers (D), supplied in the installation hardware, to attach the unit to the top cabinet. See Figurel6. Note: If mounting plates were installed using only toggle bolts, use the adjusting screws to attach the unit to the top cabinet.
4 I-? 4S72 PART NO. KHMCIOGW PRINTED IN U.S.A..
An important point after buying a device KitchenAid 1435 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought KitchenAid 1435 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data KitchenAid 1435 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, KitchenAid 1435 you will learn all the available features of the product, as well as information on its operation. The information that you get KitchenAid 1435 will certainly help you make a decision on the purchase.
If you already are a holder of KitchenAid 1435, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime KitchenAid 1435.
However, one of the most important roles played by the user manual is to help in solving problems with KitchenAid 1435. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device KitchenAid 1435 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
