Instruction/ maintenance manual of the product phd-06s King Kutter
Go to page of 20
POST HOLE DIGGERS PHD-06S, PHD-09S, PHD-12S PO Box 1200 305 Commerce Drive Winfield, Alabama 35594 ww w .kingkutter .com.
.
3 T O THE PURCHASER This manual cont ains valuable information about your new King Kutter Post Hole Digger . It has been carefully pre- p ared to give you help ful suggestions for operating, adjust- ing, servicing and ordering rep air p art s. Keep this manual in a convenient place for quick and easy reference.
4 It is the purchaser and/or operator ’ s responsibility to…. z z z z z Read and underst and the information cont ained in this manual. z z z z z Operate, lubricate, assemble and maint ain the equip- ment in accordance with all instructions and safety procedures in this manual.
5 CONTENTS ITEM P A G E Safety ......................................................................... 6 Safety Decal's And Locations ..................................... 8 Assembly Instructions .............................................. 1 0 Operating Instructions .
6 SIGNAL WORDS: The signal words DANGER , W ARNING and CAUTION are used with the safety messages in this manual and with each safety signs. They are defined as follows: DANGER: Indicates an immediate hazardous situation that, if not avoided, could result in serious injury or death.
7 EQUIPMENT SAFETY GUIDELINES z Safety of the operator and by standards is one of the main concerns in designing and developing a digger . However , every year accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment.
8.
9.
ASSEMBL Y INSTRUCTIONS 1. Att ach arch to lower hitch point s. If tractor has Category 2 hitch, use bushings provided on arch pins. 2. Attach arch to boom with pin and cotter pins provided. 3. Attach gearbox to boom with pins and cotter pins provided.
OPERA TING INSTRUCTIONS 1. Lower auger point slowly to ground. Auger point should be about 4” to the rear of the plumb line of the center of the top of the auger . 2. Set brake or use Park position. 3. Engage PTO shaft clutch at half throttle and slowly lower auger into ground.
SAFETY TRAINING z Safety is a primary concern in the design and manufacture of our product. Unfortunately , our effort s to provide safe equipment can be wiped out by a single careless act of an operator or bystander .
PREP ARTION z Never operate the tractor and post hole digger until you have read and completely under- stand this manual, the T ractor Operator ’s Manual, and each of the safety messages found on the safety signs on the tractor and digger .
OPERA TIONAL SAFETY z The use of this equipment is subject to certain hazards that cannot be protected against by the mechanical means or product design. All opera- tors of this equipment must read and understand this entire manual, pay- ing particular attention to safety and operating instructions, prior to using.
OPERA TIONAL SAFETY continued... z Never allow the auger to contact such items. Never assume an area is clear . Always Check! z Always stop the tractor , disengage PTO, set brake, shut of f the tractor engine, remove the ignition key , lower implement to the ground and allow auger to come to a complete stop before dismounting tractor .
OPERA TIONAL SAFETY continued... z Always check tractor manual for proper use on slopes. z When using a unit, a minimum 20% of tractor and equipment weight must be on tractor front wheels. Without this weight, tractor could tip over , causing personal injury or death.
Ref. No. Part Name 147300 1 Complete Collar Y oke 2 Cross Journal Set 900270 900271 900272 900273 Complete S pecial Y oke 3 PHD-S PTO 147300 17 4 Complete PTO Shield.
Post Hole Digger 18.
Ref . No . Part Name Part Number 1 Boom Complete 900253 2 9 10 14 15 16 L ynch Pin Pin w/Cotter PIns Arch Complete Bushing (2 REQ) Shear Bolt Pkg. (3/8” X 2-1/2” Grade 2, Locknut,Roll Pin 3/16” X 2”) PTO Sheild Gear Box Auger T ube Bolt Pkg.1/2”x 3-1/2 Grade 2 Bolt, Nut, Lockwasher (2ea.
1. Limited W arranty . King Kutter , Inc. (“King Kutter”), P .O. Box 1200, W infield, Alabama 35594, warrants to the original ret ail purchaser (“Purchaser”) that the product that is the subject of this sale is free from defects in material and workmanship at the time of sale.
An important point after buying a device King Kutter phd-06s (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought King Kutter phd-06s yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data King Kutter phd-06s - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, King Kutter phd-06s you will learn all the available features of the product, as well as information on its operation. The information that you get King Kutter phd-06s will certainly help you make a decision on the purchase.
If you already are a holder of King Kutter phd-06s, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime King Kutter phd-06s.
However, one of the most important roles played by the user manual is to help in solving problems with King Kutter phd-06s. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device King Kutter phd-06s along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
