Instruction/ maintenance manual of the product DF-30 Antec
Go to page of 30
D F - 3 0 D A R K F L E E T T HE A DVAN CED G AMIN G F ORCE U S E R M A N U A L.
2 DF-30 U SER ’ S M ANUAL Congratulation s on your purch ase of the An tec Dark Fleet DF-30. Meet the swif ter, lighter Da rk F leet enc losure with the hea vyweight fe ature set: the Dark F leet DF- 30.
3 T ABLE OF C ONTENT S S ECTION 1: I NTRODUCTION 1.1 Getting to know y our case……………………………… …………………. 5 1.2 Case specifications………… …………………………… …………………. 6 1.3 Before you begin…… …………………………… ………………………… 7 1.
4 I N T R O D U C T I O N S ECTION 1.
5 1.1 G ETTING TO KNOW YOUR CA SE Drive bays H ardware mounts 1 5.25” drive bays 8 Mothe rboard standoffs (pre- 2 3.5” drive ba ys instal led) 3 2.
6 1.2 C ASE S PECIFICATIONS C ASE T YPE Mid Tower C OLOR Matte black D IMENSIONS 19.1 ″ (H) x 7.8 ″ (W) x 19.1 ″ (D) 485 mm (H) x 198 mm ( W) x 486 mm (D) W EIGHT 15.
7 1.3 B EFORE Y OU B EGIN In order to ensur e that y our bui lding experie nce with the Dark Fleet DF -30 will be a positive one , please take note of the foll owing: • While worki ng inside y our Dark Fleet DF -30, keep y our case on a fla t, stable sur face.
8 1.4 L OCATING A ND P OSITIONING Y OUR C OMPUTE R Your DF-30 ha s backward s- and top-facing ex haust fans, a s well a s front-mounted intake fan s and one side - mounted front air intake. F or optimum per formance, we reco mmend leaving the front air i ntakes unobstruc ted.
9 H A R D W A R E I N S T A L L A T I O N S ECTION 2.
10 2.1 S ETTING U P Put the ca se upright on a flat, stable surface so that the rear panel (power su pply and expansio n slots) is fac ing you. To remove the left a nd right sid e panels, remove these.
11 Now rest your c ase with the left side up. He re’s what we’ll be worki ng with first: A – Po wer supply mounts B – 5 .25” drive b ay area C – 3.5 ” drive b ay area D – Fro nt panel wiring E – I/O panel Note: Do not use your fingernails to pry or lift the panels.
12 2.2 M OTHERBOARD I NSTALLATION Before proce eding: - Check the ma nual for y our CPU cooler to find out if ther e are steps you must d o before in stalling the motherboard - Make sure you have the corre ct I/O panel for y our mother board.
13 3. Now remove your mother boar d by lifting it u p. Lift your mo therboa rd ou t to install the stan doffs. 4. Install standoff s as neede d and put the motherb oard bac k in. 5. Screw in y our motherboa rd to the standoffs wit h the provid ed Phillip s-head scr ews.
14 Note: The DF-30 comes with a CPU cutou t on the motherboa rd tray, whic h will allow you to ch ange yo ur CPU heatsink without rem oving the motherb oard. 2.3 S TANDARD ATX P OWER S UPPLY I NSTALLATION The DF-30 c an accommod ate a standa rd-size ATX power su pply.
15 Use these scre ws to secure you r power sup ply to the case. 2.4 C ABLE M ANAGEMENT There is a cable manage ment compart ment behind the 3.5” d rive c age. You can tu ck or route excess c ables in this compartme nt. 1. Locate the cable manage ment c ompartment wi th cable ties l oca ted behind the walls of the 3 .
16 2.5 I NTERNAL 3.5” D EVICE I NSTALLATION The DF-30 inc ludes tw o Fleet-Re lease ™ acc ess doors. With t he front beze l facing you, they ar e located by defau lt on the bottom ni ne drive bay slots (each door cove rs three drive bay s). 1. Open the F leet-Rele ase TM acce ss door.
17 Installing a 3.5” internal d evice 3. Fasten the de vice in plac e with the pr ovided sc rews on both side of the drive cage. Make sure to install scre ws on th e left side… …as well as th e right sid e. 4. Mount any ot her 3.5” HDD de vices ac cordingly.
18 2.6 E XTERNAL 3.5” D EVICE I NSTALLATION There is one e xternal 3.5” d rive bay unde r the 5.25” d rive bays. Remove this drive b ay cov er. 1. Carefu lly remove the 3 .5” drive bay cover from the bezel. L oad the drives from the front, li ning them up to the fr ont of the dr ive ca ge.
19 2.7 U SING T HE T OP 2.5” H OT -S WAP B AY The DF-30’s t op 2.5” hard drive bay is hot-swa p capable. To u se the ho t-swap fea ture, ensur e that your motherboard is configur ed for hot-swap.
20 2.8 E XTERNAL 5.25” D EVICE I NSTALLATION There ar e three e xternally acc essible 5.25” drive bays. Before you begin, r emove both sid e pan els. 1. First, remove the drive bay fac eplate and meta l cover plate as shown bel ow. The pla stic drive ba y facep late should pop free.
21 2.9 I NTERNAL 2. 5” D EVICE I NSTALLATION There is a 2.5” devic e mounting loca tion located at the bott om of the c ase. To use t his mou nting locati on: 1. Locate the bay at the bot tom of the case. The 2.5 ” mounting location 2. Using the scr ews provide d, secu re your 2.
22 3. F RONT I/O P ORTS S ECTION 3.
23 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signa l 1 6 Positive Signa l 2 7 Ground 1 8 Ground 2 9 Key (No Connection ) 10 Empty.
24 3.3 P OWER S WITCH / R ESET S WITCH / H ARD D ISK D RIVE LED C ONNECTORS Connected to your f ront panel ar e LED and switch leads for power, re set, and HDD LED ac tivity. Attac h these to the c orrespondin g connec tors on your motherboar d. Consul t your mot herboard ma nual f or specific pin header locations.
25 C OOLI NG S YSTEM S ECTION 4.
26 4.1 I NCLUDED FANS Stand ard fans o n the DF-30 : A – 1 x 120 mm rear TwoCool™ LE D fan B – 1 x 140 mm to p TwoCoo l™ fan C – 2 x Fleet-Re lease access do or mod ules w/front va riable-sp.
27 4.2 T OP 140 MM T WO C OOL ™ F AN The DF-30 c omes with one 140mm TwoCool™ L ED fa n. This fan ha s a two- speed switc h that lets y ou choose the s peed be st suited to your nee d and a switch to turn on or off t he LED. T hese sw itches ar e located at the rear of the ca se.
28 4.4 R EAR E XHAUST 120 MM T WO C OOL ™ F ANS There is one 12 0 x 25 mm T woCool ™ blue LED f an preinstall ed a t the rear of the case . This fan is designed to pull hot air out of the c ase. Each fa n comes with t wo-spee d switch that let y ou choo se the spe ed best suited to your need .
29 4.6 W ASHABLE A IR F ILTERS There is a filter locate d behind the f aceplate of each Fle et-Release TM Access Do ors. There are total of t hree front air filter s that come with the case. Removin g the wa shable air filter. Note the filter tabs. To clean the fi lter: 1.
30 Antec, Inc. 47900 Fre mont Blvd. Fremont, CA 945 38 tel: 510-770-12 00 fax: 510-770-1288 Antec Europe B.V. Stuttgartstra at 12 3047 AS Rotterd am The Netherland s tel: +31 (0) 10 46 2-2060 fax: +31 (0) 10 4 37-1752 Technical Supp ort: US & Canad a 1-800-22ANT EC customersup port@antec.
An important point after buying a device Antec DF-30 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Antec DF-30 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Antec DF-30 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Antec DF-30 you will learn all the available features of the product, as well as information on its operation. The information that you get Antec DF-30 will certainly help you make a decision on the purchase.
If you already are a holder of Antec DF-30, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Antec DF-30.
However, one of the most important roles played by the user manual is to help in solving problems with Antec DF-30. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Antec DF-30 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
