Instruction/ maintenance manual of the product cx600.5 Kicker
Go to page of 32
CX MUL TI-CHANNEL AMPS CX600.5 Owner’s Manual | English Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE CX.5 Benutzerhandbuch | Deutsch VERSTÄRKER DER CX.5-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE CX.5 CX Amplifiers 2012 CX 5-Channel Amp Rev F.
2 CX.5-SERIES AMPLIFIERS OWNER’S MANUAL INST ALLA TION Mounting: Choose a structurally sound location to mount your KICKER amplifi er . Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er .
3 Wiring: Disconnect the vehicle’ s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er . Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’ s chassis.
4 POWER WIRING GND REM +12V 12V AMP1 AMP2 SUB L R S S L R battery external fuse remote turn-on (see page 6) bare-metal chassis ground bare-metal chassis ground 18” (45cm) 24” (60cm) Model External Fuse (sold separately) Power/Ground W ire KICKER W iring Kit CX600.
5 CXRC REMOTE BASS INST ALLA TION (See page 6. CXRC not included.) back view AMP1 AMP2 SUB L R S S L R GND REM +12V FOUR CHANNEL OPERA TION with SUBWOOFER minimum impedance of 2 ohms per channel (AMP1, AMP2, and SUB channels) Surface-mount the CXRC remote using the supplied screws.
6 OPERA TION Automatic T ur n-On Selection: The CX series offers two different automatic turn-on modes; +12V and DC Offset. • Remote T urn-On: Run 18 gauge wire from the Remote T urn-On Lead on your source unit to the terminal labeled REM between the amplifi er ’ s positive and negative power terminals.
7 TROUBLESHOOTING If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There are Power (PWR) & Protection (PRT) LEDs on the side panel of your Kicker CX series amplifi er .
8 KICKER will now provide a thr ee- year warranty with all CX-Series Amplifi er purchases paired with a qualifying KICKER Installation Kit* . This extends the standard warranty by an additional year . Amplifi er and Kit must be purchased from an Authorized KICKER Dealer .
9 Modelo: CX600.5 Alimentación RMS, AMP1 y AMP2 @ 14.4V , 4 estéreo, 1% THD+N @ 14.4V , 2 estéreo, 1% THD+N @ 14.4V , 4 mono, 1% THD+N 40W x 4 75W x 4 150W x 2 Alimentación, SUB canal @ 14.4V , 2 Ω monofónico, 1.5% THD+N @ 14.
10 soporte de doble ranura tornillos hexagonales panel de fondo del amplifi cador Los Amplifi cadores CX de KICKER se pueden instalar verticalmente para ahorrar espacio.
11 GND REM +12V 12V AMP1 AMP2 SUB L R S S L R batería fusible externo encendido a distancia (página 13) conexión a tierra 18” (45cm) 24” (60cm) Modelo Fusible Externo (no incluido) Cable de Alimentación y Conexión a T ierra Kit de cableado KICKER CX600.
12 CXRC CONTROL REMOTO DE BAJOS INST ALACIÓN (no incluido CXRC. V ea la página 13) AMP1 AMP2 SUB L R S S L R GND REM +12V FUNCIONAMIENTO POR CUA TRO CANALES CON SUBWOOFER impedancia mínima de 2 ohmios por canales (AMP1, AMP2, y SUB canales) vista desde atrás Para instalar en superfi cie el control remoto CXRC use los tornillos suministrados.
13 señal de entrada FUNCIONAMIENTO Selección de Encendido Automático: El modelo CX le ofrece dos distintos modos de encendido automático; desvío a +12V y DC.
14 RESOLUCIÓN DE PROBLEMAS Si su amplifi cador parece no estar funcionando, revise lo obvio primero: fusibles quemados, conexiones malas o incorrectas, posición incorrecta de los selectores de crossover y amplifi cación, etc.
15 CX600.5 40 x 4 @ 4 ohmios (20Hz–20,000Hz) Relación de Señal a Ruido -75dB CEA-2006B (ref: 1W , ponderado en A) 150 x 1 @ 4 ohmios (25Hz–200Hz) Relación de Señal a Ruido -75dB CEA-2006B (ref: 1W , ponderado en A) 14.4VCC, 1% THD, CEA-2006B (W) 2012 CX 5-Channel Amp Rev F.
16 Modell: CX600.5 RMS-Leistung, AMP1 und AMP2 @ 14.4V , 4 Ω stereo, 1% Gesamtklirrfaktor @ 14.4V , 2 Ω stereo, 1% Gesamtklirrfaktor @ 14.4V , 4 Ω mono, 1% Gesamtklirrfaktor 40W x 4 75W x 4 150W x 2 RMS-Leistung, SUB kanal @ 14.4V , 2 Ω mono, 1,5% Gesamtklirrfaktor @ 14.
17 Anschluss: T rennen Sie den Anschluss der Fahrzeugbatterie, um einen Kurzschluss zu vermeiden. Schließen Sie dann das Massekabel an den V erstärker an. Verwenden Sie ein kurzes Erdungskabel (maximal 60 cm) und schließen Sie es an eine lack- oder korrosionsfreie Metallstelle an der Fahrzeugkarosserie an.
18 GND REM +12V 12V AMP1 AMP2 SUB L R S S L R Batterie Ferneinschaltung (Seite 20) Masse 18” (45cm) 24” (60cm) externe Sicherung Modell Externe Sicherung (nicht inbegriffen) Massekabel KICKER V erkabelungssatz CX600.
19 CXRC BASSPEGEL-FERNBEDIENUNG INST ALLA TION (CXRC nicht inbegriffen. Siehe Seite 20.) AMP1 AMP2 SUB L R S S L R GND REM +12V VIERKANALBETRIEB MIT SUBWOOFER Minimal impedanz von 2 Ohm pro Kanal (AMP1, AMP2, und SUB Kanäle) Stecken Sie das mitgelieferte 1/8 Zoll [3.
20 BETRIEB Automatische Einschaltung: Die CX-Serie umfasst zwei automatische Einschaltmodi: +12V und DC Offset. • Remote T urn-On (Ferneinschaltung): Verlegen Sie 18 GA-Kabel von der Ferneinschaltung an Ihrem Autoradio zum REM-T erminal zwischen den positiven und negativen Stromanschlüssen des Verstärkers.
21 PROBLEMBEHEBUNG Wenn der V erstärker nicht zu funktionieren scheint, sollten Sie zuerst offensichtliche Faktoren prüfen, wie durchgebrannte Sicherungen, schlechte oder fehlerhafte V erkabelung, inkorrekte Einstellung des Crossover- Schalters und der V erstärkungsregler etc.
22 CX600.5 40 x 4 @ 4 ohms (20Hz–20,000Hz) Rauschabstand -75dB CEA-2006B (ref: 1W , A-gewichtet) 150 x 1 @ 4 ohms (25Hz–200Hz) Rauschabstand -75dB CEA-2006B (ref: 1W , A-gewichtet) 14.4V GS, 1% Klirrfaktor , CEA-2006B (Watts) 2012 CX 5-Channel Amp Rev F.
23 Modèle: CX600.5 Puissance Effi cace @ 14.4V , 4 Ω stéréo, 1% THD+N @ 14.4V , 2 Ω stéréo, 1% THD+N @ 14.4V , 4 Ω mono, 1% THD+N 40W x 4 75W x 4 150W x 2 Puissance Effi cace @ 14.
24 vis hexagonales panneau d’extrémité de l’amplifi cateur bride à double fente Câblage: Débranchez la batterie du véhicule pour éviter un court-circuit. Ensuite, raccordez le fi l de masse à l’amplifi cateur . Le fi l de masse doit être le plus court possible, de 60 cm (24 po) maximum.
25 Modèle Fusible Externe (non inclus) Fil de Masse / Alimentation KICKER Kit de câblage CX600.5 1 x 80 Ampères Calibre 4 PK4, CK44, ZCK44 GND REM +12V 12V AMP1 AMP2 SUB L R S S L R Batterie Mise s.
26 CXRC TÉLÉCOMMANDE DU NIVEAU DES GRA VES INST ALLA TION (CXRC non inclus. V oir page 27.) AMP1 AMP2 SUB L R S S L R GND REM +12V FONCTIONNEMENT À QUA TRE CANAUX A VEC CAISSON DE GRA VES impédance minimum de 2 ohms par canal (AMP1, AMP2, et le SUB canaux Installez la télécommande CXRC en surface en utilisant les vis fournies.
27 UTILISA TION Sélection de Mise sous T ension Automatique : La série CX propose deux modes d’allumage automatique différents ; +12 V et décalage en continu.
28 EN CAS DE DIFFICUL TÉ Si votre amplifi cateur ne marche pas, vérifi ez d’abord les possibilités évidentes comme les fusibles sautés, les branchements incorrects ou desserrés, le mauvais réglage des commandes de gain et du commutateur du fi ltre, etc.
29 CX600.5 40 x 4 @ 4 ohms (20Hz–20,000Hz) Rapport Signal sur Bruit -75dB CEA-2006B (ref: 1W , pondéré A) 150 x 1 @ 4 ohms (20Hz–200Hz) Rapport Signal sur Bruit -75dB CEA-2006B (ref: 1W , pondéré A) 14.4V C.C., 1% de Distorsion Harmonique T otale, CEA-2006B (W) 2012 CX 5-Channel Amp Rev F.
30 ELECTRONICS LIMITED W ARRANTY When purchased from an Authorized KICKER Dealer , KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt.
31 P .O. Box 459 • Stillwater , Oklahoma 74076 • USA • (405) 624–8510 INTERNA TIONAL W ARRANTY Contact your International KICKER dealer or distributor concerning specifi c procedures for your country’s warranty policies.
©2012 Stillwater Designs 2012 CX 5-Channel Amp Rev F.indd 32 2012 CX 5-Channel Amp Rev F.indd 32 6/22/2012 3:09:05 PM 6/22/2012 3:09:05 PM.
An important point after buying a device Kicker cx600.5 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kicker cx600.5 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kicker cx600.5 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kicker cx600.5 you will learn all the available features of the product, as well as information on its operation. The information that you get Kicker cx600.5 will certainly help you make a decision on the purchase.
If you already are a holder of Kicker cx600.5, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kicker cx600.5.
However, one of the most important roles played by the user manual is to help in solving problems with Kicker cx600.5. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kicker cx600.5 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
