Instruction/ maintenance manual of the product UL/C-UL Kenyon
Go to page of 16
INSTRUCTION MANUAL Mediterranean 2-Burner Caribbean 2-Burner Mediterranean, Caribbean & Alpine Ceramic Glass Cook Tops (240 Volt Models UL/C-UL APPROVED) KENYON P.
P LE ASE RE AD THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE INST ALLATION AND USE OF APPLIANCE . *** DO NOT DISCARD THIS MANUAL ! S A VE FOR FUTURE REFERENCE .
Mediterranean Series Cook Top PRODUCT SPECIFICATIONS Two Burner B41511 - 240V AC - one 6” (165mm) burner @ 1200 watts one 8” (200mm) burner @ 1800 watts Overall dimensions: 23-1/4” x 14-1/4” x 2-5/8” 590.6mm x 362.0mm x 66.7mm Cutout dimensions: 21-3/4” x 12-3/4” with 1/4” radius 552.
Caribbean Series Cook Top PRODUCT SPECIFICATIONS Two Burner B41602 - 240V AC - two 6” (165mm) burners @ 1200 watts each Overall dimensions: 21” x 12” x 2-5/8” 533.4mm x 304.8mm x 63.5mm Cutout dimensions: 20” x 10-3/4” with 1/4” radius 508mm x 273mm with 6.
Alpine Series Cook Top PRODUCT SPECIFICATIONS Two Burner - Large B49511 - 240V AC - one 6” (165mm) burner @ 1200 watts one 8” (200mm) burner @ 1800 watts Overall dimensions: 23-1/4” x 14-1/4” x 2-5/8” 590.6mm x 362.0mm x 66.7mm Cutout dimensions: 21-3/4” x 12-3/4” with 1/4” radius 552.
INSTALLATION INSTRUCTIONS FOR KENYON CERAMIC GLASS COOK TOPS Important : Save this documentation for review by local inspector. Important: This appliance must be properly installed and grounded by a qualified technician. STEP #1 Unpacking the Cook Top Carefully unpack the cook top from its shipping container.
For future reference, please record the serial number of your cook top here: STEP #2 Check the Electrical Supply Requirements This product must be installed in accordance with national, state and local electric codes. The following table provides the correct voltage, amperage and frequency that must be supplied to the cook top.
STEP #3 Countertop Preparation Please read this section prior to making cutout for cook top. It is important to plan ahead for installation of the cook top, keeping the following dimensions in mind (please refer to Figure A).
Allow a 2” minimum clearance between the bottom of the metal pan of the cook top and any combustible surface located below, ie: the upper edge of a drawer installed below the cook top (see Fig. B on previous page). Failure to provide proper clearances and ventilation may result in a fire hazard.
5 STEP #4 Installing the Cook Top There are two mounting brackets supplied with the glass ceramic cook top. These brackets are designed to hold the cook top firmly in place.
STEP #5 Electrical Connection Before proceeding further, verify that the power supply is disconnected. Verify that the appropriate electrical supply requirements have been met. Please refer to the table on page 2 for appropriate electrical requirements.
USER’S GUIDE & CARE SAFETY Read this section BEFORE operating the cook top. The following information applies to all KENYON Electric Cook Tops. • Proper Installation Be sure your appliance is properly installed and grounded by a qualified technician.
• Do not use water on grease fires. Smother fire or flame or use dry chemical or foam-type extinguisher. • Use only dry potholders. Moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholder touch the heating elements on the appliance.
OPERATION READ SAFETY INSTRUCTIONS BEFORE OPERATING YOUR APPLIANCE The cooking surface areas of your glass ceramic cook top are identified by permanent patterns in the cook top.
Knobs & Indicator Lights (continued) There are a series of lights that provide indications of burner operation and hot surfaces. These lights are located adjacent to the control knobs. When the control is in the “on” position, a red light is lit indicating which burner is on.
W ARRANTY KENYON International (the “Company”) warrants its products in normal usage to be free of defects in materials and workmanship subject to the conditions and limitations below. Any part which proves to be defective in normal usage during the warranty period will be repaired or replaced by the Company.
An important point after buying a device Kenyon UL/C-UL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenyon UL/C-UL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenyon UL/C-UL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenyon UL/C-UL you will learn all the available features of the product, as well as information on its operation. The information that you get Kenyon UL/C-UL will certainly help you make a decision on the purchase.
If you already are a holder of Kenyon UL/C-UL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenyon UL/C-UL.
However, one of the most important roles played by the user manual is to help in solving problems with Kenyon UL/C-UL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenyon UL/C-UL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
