Instruction/ maintenance manual of the product LZ-800W Kenwood
Go to page of 16
© PRINTED IN JAPAN B64-1715-00 (W) (+) 01/12 11 10 9 8 7 6 5 4 3 2 1 00/12 11 10 9 8 7 LZ-800W INSTR UCTION MANU AL 8-Inch WIDE MONIT OR Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new monitor.
English 2 Contents S S a a f f e e t t y y P P r r e e c c a a u u t t i i o o n n s s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 To prevent injury and/or fire, take the following precautions: • Ensure that the unit is securely installed. Otherwise it may fly out of place during collisions and other jolts. • When extending the ignition or ground wires, make sure to use automotive-grade wires or other cables with an area of 0.
English 4 Monitor Control Function Turning on the power Press the PWR button. Turning off the power Press the PWR button for at least one second. Each time you press the V.
5 You cannot operate when the wide picture navigation is displayed. Each time you press the PWR button, the AV output mode switches as follows: ● When the Video Box Unit is connected ▼ [NORMAL]: P.
English 6 System Setup Function ● When the Video Box Unit is connected Press the SCRN button for at least one second to switch to the setup menu screen. Touch [ SYSTEM ] to switch to the system setting screen. Setting the Navigation Input Mode [NAV] Touch [ RGB ], [ VD1 ] or [ VD2 ].
7 Setting the Touch Sensor Tone [BEEP] Touch [ ON ] or [ OFF ] to switch the function on and off. [ON]: Touch sensor tone is turned on [OFF]: Touch sensor tone is turned off Touch [ 2 ] to return to the system setting screen-1. Touch [ RTN ] to return to the setup menu screen.
English 8 TV Control Function < When The KTC-V800N/KTC-V800P is connected > Press the V.SEL button repeatedly to select the TV picture. Touch the part C to switch to the TV control screen. Each time you touch [ BAND ], the preset band switches between the TV1 and TV2.
9 Selecting the Preset Bands Each time you touch part B , the preset band switches between the TV1 and TV2. Selecting the Channels Auto Seek Tuning (AUTO1) Touch the part D to seek for channels up the band. Touch the part A to seek for channels down the band.
English 10 Remote Control Function <Provided with the KTC-V800N/KTC-V800P> Monitor Control Function • VOL button Press the 5 button to increase the volume of the built-in speaker. Press the ∞ button to decrease the volume of the built-in speaker.
11 Installation 1. To prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery. 2. Make the proper input and output cable connections for each unit. 3. Connect the wiring harness cables in the following order: ground, ignition.
English 12 Installation Installation for Monitor Unit Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A .
13 Installation for the Video Box Unit Connecting the Power 2 AV INPUT AV OUTPUT 1 AV INPUT PRK SW FM-TX – + +12V ■ Securing to audio board ■ Securing to pile carpet Accessory 5 (Ø4 x 16 mm) Accessory 6 Please do not install the unit near the dashboard, the rear tray, or other important components.
English 14 Installation Connecting the Headphone / AV Equipments Stereo Mini Plug (Ø3.5) Headphone ■ Connecting the Headphone ■ Connecting the AV Equipment Audio/Visual input 1 • Audio right in.
15 Tr oubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. SOLUTION POSSIBLE CAUSE PROBLEM Nothing happens when the buttons are pressed.
English 16 Specifications Specifications subject to change without notice. Monitor Unit Screen size ..................................................................................................................8. 0 inches wide 176.4(W) x 99.2(H) x 202(Diagonal) mm 6-15/16(W) x 3-7/8(H) inch Display system .
An important point after buying a device Kenwood LZ-800W (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenwood LZ-800W yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenwood LZ-800W - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenwood LZ-800W you will learn all the available features of the product, as well as information on its operation. The information that you get Kenwood LZ-800W will certainly help you make a decision on the purchase.
If you already are a holder of Kenwood LZ-800W, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenwood LZ-800W.
However, one of the most important roles played by the user manual is to help in solving problems with Kenwood LZ-800W. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenwood LZ-800W along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
