Instruction/ maintenance manual of the product KRC-265S Kenwood
Go to page of 22
KRC-265 KRC-265S © B64-2102-00 (MW/MN) CASSETTE RECEIVER INSTR UCTION MANU AL KRC-265/265S(M_K)_Cover_r1 01.10.3 6:07 PM Page 1.
— 2 — English Contents Safety precautions .................................................3 About Cassette tape ..................................
— 3 — To prevent injury or fire, take the following precautions: •I nsert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English • If you experience problems during installation, consult your Kenwood dealer . • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer .
Press the [SRC] button. Source required Display T uner "TUnE" T ape "T APE" External disc "DISC" Standby (Illumination only mode) "OFF" Selecting the Source Tu rning ON the Power Press the [SRC] button. Tu rning OFF the Power Press the [PWR OFF] button for at least 1 second.
1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [A.ADJ] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below .
The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate Press the Release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts.
Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUnE" display . 2 Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. 3 Tu ne up or down the band Press the [ 4 ] or [ ¢ ] button.
Changing the tuning frequency step. The original setting is FM band 50 kHz, and AM band 9 kHz. 1 Tu rn the power OFF Press the [SRC] button for at least 1 second. 2 Switch the frequency step While pressing the [#1] and [#5] button, press the [SRC] button.
Switching to the radio automatically during Fast Forwarding and Rewinding. Press the [TC] button. Each time the button is pressed the T uner Call turns ON or OFF . When it's ON, the "T .CALL" indicator is ON. When you turn ON the T uner Call function, the motorized antenna will extend automatically .
Fast Forwarding Hold down on the [ ¢ ] button. Release your finger to play the disc at that point. Reversing Hold down on the [ 4 ] button. Release your finger to play the disc at that point. Fast Forwarding and Reversing Playing discs set in the optional accessory disc player connected to this unit.
Playing all the songs on the disc in random order . Press the [RDM] button. Each time the button is pressed Random Play turns ON or OFF . When it's ON, the "RDM" indicator is ON and the track number blinks. When the [ ¢ ] button is pressed, the next song select starts.
Play the songs on all the discs in the disc changer in random order . Press the [M.RDM] button. Each time the button is pressed the Magazine Random Play turns ON or OFF . When it's ON, the "RDM" indicator is ON and the track and disc number blink.
English — 14 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery .
— 15 — FRONT ¥ L FRONT ¥ R REAR ¥ L REAR ¥ R P.CONT ANT CONT FM/AM antenna input 1 Rear left output (White) 23 Rear right output (Red) 28 Fuse (10A) 24 KENWOOD disc changer control input 2 Wir.
English — 16 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support Screw (M4X8) (commercially available) ■ Installation 8 mm MAX.
— 17 — ■ Removing the hard rubber frame 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner . Catch Lock 1 Engage the catch pins on the removal tool and remove the two locks on the lower level.
English — 18 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. 01 ✔ The fuse has blown.
— 19 — T uner source ? Radio reception is poor . 39 ✔ The car antenna is not extended. ☞ Pull the antenna out all the way . ✔ The antenna control wire is not connected. 40 ☞ Connect the wire correctly , referring to the section on <Connecting Wires to T erminals>.
English — 20 — The messages shown below display your systems condition. E-01: No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. E01 ➪ Load the disc magazine properly . E-02: No disc has been loaded in the disc magazine.
— 21 — FM tuner section Frequency range (50 kHz space) ...............87.5 MHz –108.0 MHz (200 kHz space) .............87.9 MHz –107.9 MHz Usable sensitivity (S/N = 30dB) ................... 9.3 dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) .
KRC-265(M_K)_Ch_r4 01.10.3, 5:37 PM 22.
An important point after buying a device Kenwood KRC-265S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenwood KRC-265S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenwood KRC-265S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenwood KRC-265S you will learn all the available features of the product, as well as information on its operation. The information that you get Kenwood KRC-265S will certainly help you make a decision on the purchase.
If you already are a holder of Kenwood KRC-265S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenwood KRC-265S.
However, one of the most important roles played by the user manual is to help in solving problems with Kenwood KRC-265S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenwood KRC-265S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
