Instruction/ maintenance manual of the product KGC-9044 Kenwood
Go to page of 13
KGC-9044 © B64-1423-00 (E) (MC) 00/2 1 99/12 11 10 9 8 7 6 5 4 3 2 1 11 BAND GRAPHIC EQU ALIZER INSTR UCTION MANU AL.
Contents — 2 — English Before use Safety precautions ..................................................................3 Buttons and Display .....................................................4 Equalizer operations KBS (Kenwood Built-in Sound) .
— 3 — Saf ety precautions To prevent injury and/or fire, take the following precautions: • Insert the unit all the way until it is fully locked in place. Otherwise it may fly out of place during collisions and other jolts. • When extending the battery or ground.
Four types of loudness levels and equalizer curves for rock, pops, vocal, and flat music genre have been preset. You can call up an equalizer curve for each genre at the touch of a button. Switching between KBS1, KBS2 and USER: Press the EQ button. Each time you press the EQ button, the function changes from KBS1 to KBS2 to USER.
— 5 — You can adjust the sound level to suit your preference among 11 frequencies: 60 Hz, 120 Hz, 250 Hz, 380 Hz, 500 Hz, 750 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, and 16 kHz.
— 6 — English Other operations Menu System To accommodate a greater number of functions, a function set system has been employed for making settings. Press the MENU button to enter the function set mode and then display the function to make the setting.
— 7 — Spectrum Analyzer Display Selection You can select the display to enjoy sounds with eyes. Switching the Spectrum Analyzer Display: Each time you press the S.A button, the spectrum analyzer display switches as follows; ▼ 1 "SCAN MODE ON":Displays 2 to 9 are automatically shown in succession for about five seconds each.
Reattaching Faceplate: Hold the faceplate so that the operation face faces the front toward you and press until it locks. The faceplate will be set and the unit will be operational. When there is difficulty in setting the faceplate, align the depression on the left side of the faceplate with the shaft of the unit, then lock.
— 9 — Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output cable connections for each unit. 3. Connect the wiring harness cables in the following order: ground, battery.
— 10 — English Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support Accessory 3 Installation ■ Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.
— 11 — When the lower level is removed, remove the upper two locations. 2 The frame can be removed from the top side in the same manner. NOTE Catch Lock Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure.
— 12 — English Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. SOLUTION POSSIBLE CAUSE PROBLEM The fader and/or balance settings are set all the way to one side.
— 13 — Equalizer section Equalizer centre frequencies ............ 60 Hz, 120 Hz, 250 Hz, 380 Hz, 500 Hz, 750 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz Equalizer range ........................................................-10 ~ +10 dB Subwoofer Cut-off Frequency .
An important point after buying a device Kenwood KGC-9044 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenwood KGC-9044 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenwood KGC-9044 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenwood KGC-9044 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenwood KGC-9044 will certainly help you make a decision on the purchase.
If you already are a holder of Kenwood KGC-9044, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenwood KGC-9044.
However, one of the most important roles played by the user manual is to help in solving problems with Kenwood KGC-9044. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenwood KGC-9044 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
