Instruction/ maintenance manual of the product KDC-MP5029 Kenwood
Go to page of 34
CD-RECEIVER KDC-MP6029 KDC-MP5029 INSTR UCTION MANU AL © B64-2950-00/00 (MW) B64-2950-00_English.indd 1 B64-2950-00_English.indd 1 04.11.9 0:52:48 PM 04.
2 | English Con tents Safety precautions 3 Notes 4 About CDs 5 About AA C,MP3 and WMA 6 General featur es 7 Pow er Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Speaker Set.
English | 3 Safety precautions About CD play ers/disc changers connected to this unit KENWOOD disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenw ood dealer for connectable models of disc changers/ CD players.
4 | English Notes • If you experience problems during installation, consult your Kenwood dealer . • If the unit fails to operate properly , press the Reset button. The unit returns to factory settings when the Reset button is pressed. • P ress the reset button if the disc auto changer fails to operate correctly .
English | 5 Handling CDs • Don ’t touch the recor ding sur face of the CD . • CD-R and CD-R W are easier t o damage than a normal music CD. Use a CD-R or a CD-R W after reading the caution items on the package etc. • Don ’t stick tape etc. on the CD .
6 | English About AA C, MP3 and WMA The playable AAC/MP3/WMA file (her eafter called Audio file) and the media format has the f ollowing limitation. The Audio file, which is out of the specification, may not able to be played normally , or the file and folder names may not be display ed correctly.
English | 7 General fea tures Powe r T urning ON the P ower Press the [SRC] button. • When the power is ON, the <Security Code> (page 20) is displayed as "CODE ON" or "C ODE OFF" . T urning OFF the P ower Press the [SRC] button for at least 1 sec ond.
8 | English General fea tures Attenua tor T urning the volume down quickly . Press the [ A T T ] button. Each time the button is pressed, the Att enuator turns ON and OFF . When it’ s ON, the " A T T" indicator blinks. Sy stem Q Y ou can recall the best sound setting preset for different types of music.
English | 9 Adjustment Item Display Range Fr ont High Pass Filter * 2 "HPF" Thr ough/80/100/120/150 /180 Hz Rear High P ass Filter * 2 "HPR" Thr ough/80/100/120/150 /180 Hz Low P a.
10 | English General fea tures Switching Displa y Switching the information displa yed. 1 Enter S witching Display mode Press the C ontrol knob for at least 1 second. "DISP SEL " is displayed. 2 Select the Display item Push the Contr ol knob to [ 4 ] or [ ¢ ].
English | 11 TEL Mute The audio system automatically mutes when a call comes in. When a call comes in "CALL " is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL " display disappears and the audio system comes back ON.
12 | English T uner/T V contr ol featur es T uning Selecting the station. 1 Select tuner source Press the [SRC] button. Select the " TUNER" display . 2 Select the band Push the Contr ol knob to [FM] or [AM]. Each time the knob is pushed to [FM], it switches between the FM1, F M2, and FM3 bands.
English | 13 Example: Desired frequency Pr ess button 92.1 MHz (FM) [0], [9], [2], [1] 810 kHz (A M) [0], [8], [1], [0] Canceling Dir ec t A ccess T uning Press the [DIRECT ] button on the remot e. Station Pr eset Memor y Putting the station in the memory.
14 | English T uner/T V contr ol featur es F unction of the KDC-MP6029 F unction of LX BUS T elevision TV channel Preset Memory Putting the T V channels in the memory . 1 Select the TV band Press the [F M] button. 2 Select the TV channel to put in the memory Push the Contr ol knob to [ 4 ] or [ ¢ ].
English | 15 CD/Audio file/External disc contr ol features Playing CD & A udio file When there is no disc inserted 1 Drop open the faceplate Press the Release button. 2 Inser t a disc. 3 Push the faceplate on the left side, and return it to its former position.
16 | English CD/Audio file/External disc contr ol features Playing External Disc Playing discs set in the optional accessory disc player connected to this unit.
English | 17 In CD & External disc source Repeat play Display T rack Repeat "TRAC REP" Disc Repeat (In Disc Changer) "DISC REP" OFF "REP OFF" In Audio file Repeat pla.
18 | English CD/Audio file/External disc contr ol features T ext/Title Scroll Scrolling the displayed CD text, Audio file t ext, or MD title. Hold down on [FM] of the C ontrol knob for at least 1 second. B64-2950-00_English.indd 18 B64-2950-00_English.
English | 19 Menu system Menu Sy stem Setting during operation beep sound etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. 1 Enter Menu mode Press the [MENU] button f or at least 1 second.
20 | English Menu system In Standby mode Secur ity C ode Because authorization by the Security Code is required when it’ s removed from the vehicle , personalizing this unit is by using the Security Code is a help in preventing theft. • When the Security Code function is activated, it can’t be released.
English | 21 In Standby mode DSI (Disabled Sy stem Indicator) A red indicator will blink on the unit after the faceplate is remov ed, warning potential thieves.
22 | English Menu system Auxiliary Input Display Setting For selecting the display when swit ched to Auxiliary input source. 1 S elect Auxiliary input source Press the [SRC] button. Select the " A UX EXT " display . 2 Enter Menu mode Press the [MENU] button f or at least 1 second.
English | 23 Basic Operations of r emote Loading and Replacing the battery Use two " AA "-size batteries. Slide the cover while pr essing downwards to remove it as illustrated . Inser t the batteries with the + and – poles alig ned properly , following the illustration inside the case .
24 | English Basic Operations of r emote Audio C ontrol [A UD] button Select the Audio item for adjustment. [VOL] buttons Adjust the Audio item. • Refer to <Audio C ontrol> (page 8) for the operation method, such as the procedures of A udio control and others.
English | 25 Ac cessories/ Installation P rocedure Ac cessories 1 ..........1 2 ..........2 3 ..........4 4 ..........4 5 ..........1 6 ..........2 7 ..........1 8 ..........1 Installation Proc edure 1. T o prevent a shor t cir cuit, remove the key from the ignition and disconnect the - battery.
26 | English Connecting Wires to T erminals (KDC-MP6029) ANT. CONT MUTE P.CONT ILLUM FRONT L FRONT R REAR L REAR R – + SUB WOOFER Battery Ground wire (Black) - ( T o car chassis) FM/AM antenna input.
English | 27 Connecting Wires to T erminals (KDC-MP5029) ANT. CONT MUTE P.CONT FRONT L FRONT R REAR L REAR R – + FRONT Battery Ground wire (Black) - ( T o car chassis) FM/AM antenna input F use (10A.
28 | English Installation • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). non-Japanese cars Japanese cars 1 Refer to the section <Removing the hard rubber frame> (page 30) and then remove the hard rubber frame.
English | 29 Screwing the F acepla te on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off . 1 Refer to the section <Removing the hard rubber frame> (page 30) and then remove the hard rubber frame. 2 Drop open the faceplate by pressing the Release button.
30 | English Removing the Unit Removing the hard rubber fr ame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level . Upper the frame and pull it forward as shown in the figure. 2 When the upper level is removed, r emove the lower two locations.
What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Befor e calling ser vice , first check the following table f or possible problems. General ? The pow er does not turn ON. ✔ The fuse has blo wn.
Disc source ? " AUX" is displa yed without achieving External disc control mode . ✔ Unsupported disc changer is connected. ☞ Use the disc changer mentioned in the <About CD players/disc changers connected to this unit> (page 3) of the section on <Safety precautions>.
The messages shown belo w display your systems condition. EJEC T: No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. ➪ Load the disc magazine pr operly. No CD in the unit. ➪ Inser t the CD. NO DISC: No disc has been loaded in the disc magazine.
34 | English Specifications Specifications subject to change without notice. FM tuner section Fr equency range (50 kH z space) : 87.5 MHz – 108 MH z Fr equency range (200 kH z space) : 87.9 MHz – 107.9 MH z Usable sensitivity (S/N = 30dB) : 9.3dBf (0.
An important point after buying a device Kenwood KDC-MP5029 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenwood KDC-MP5029 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenwood KDC-MP5029 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenwood KDC-MP5029 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenwood KDC-MP5029 will certainly help you make a decision on the purchase.
If you already are a holder of Kenwood KDC-MP5029, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenwood KDC-MP5029.
However, one of the most important roles played by the user manual is to help in solving problems with Kenwood KDC-MP5029. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenwood KDC-MP5029 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
