Instruction/ maintenance manual of the product KDC-1032 Kenwood
Go to page of 22
KDC-132 KDC-1032 KDC-132CR CD-RECEIVER INSTR UCTION MANU AL © B64-3239-00/00 (KW/KN) T ake the time to r ead through this instruction manual. F amiliarity with installation and operation procedur es will help you obtain the best performance from your new CD-receiv er .
2 | English Con tents W arning 3 Safety precautions 4 Notes 5 About CDs 6 General featur es 7 Pow er Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Speaker Setting Clock Dis.
English | 3 2 W arning 2 CAUTION Use of controls or adjustments or performance of procedures other than those specified her ein may result in hazardous radiation exposur e. In compliance with Federal Regulations, f ollowing are repr oductions of labels on, or inside the product relating to laser product saf ety.
4 | English Safety precautions Lens F ogging When you turn on the car heater in cold weather , dew or condensation may form on the lens in the CD player of the unit. Called lens fogg ing, this condesnation on the lens may not allow CDs to play . In such a situation, remove the disc and wait for the condensation to evaporate .
English | 5 • If you experience problems during installation, consult your Kenwood dealer . • If the unit fails to operate properly , press the Reset button. The unit returns to factory settings when the Reset button is pressed. • Characters in the L CD may become difficult to read in temperatures below 5 ˚C (41 ˚F).
6 | English Handling CDs • Do not touch the recor ding sur face of the CD. • CD-R and CD-R W are easier to damage than a normal music CD. Use a CD-R or a CD-R W after reading the caution items on the package etc. • Do not stick tape etc. on the CD , or use a CD with tape stuck on it.
English | 7 General fea tures Powe r T urning ON the Power Press the [SRC] button. T urning OFF the Power Press the [SRC] button for at least 1 sec ond.
8 | English General fea tures Sy stem Q Selecting the best sound setting preset for different types of music. 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [ Q] button. When you press the button once , the current sound setting is displayed.
English | 9 Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "STBY" display. 2 Enter Speaker Setting mode Press the [VOL] knob. 3 Select the Speaker type T urn the [ VOL] knob.
10 | English General fea tures Theft Deterrent F aceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the F aceplate Press the Release button. The faceplate unlocks, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts.
English | 11 T uner featur es T uning Selecting the station. 1 Select tuner source Press the [SRC] button. Select the " TUnE" display . 2 Select the band Push the Contr ol knob towards [FM] or [ AM]. Each time you push the knob toward [FM], it switches between the FM1, F M2, and FM3 bands.
12 | English T uner featur es Station Pr eset Memor y Putting a station in the memory. 1 Select the band Push the Contr ol knob towards [FM] or [ AM]. 2 Select the frequency to put in the memor y Push the Contr ol knob towards [ 4 ] or [ ¢ ]. 3 Put the frequency in the memory Press the desired [1] — [6] butt on for at least 2 seconds.
English | 13 CD play er featur es Playing CD When a disc is inserted Press the [SRC] button. Select the "CD" display. • When a CD is inserted, the "IN" indicator is ON. Pause and play Press the C ontrol knob. Each time you press the knob, the audio pauses or plays.
14 | English CD play er featur es T rack Search Selecting the song you want to hear . Push the Contr ol knob towards [ 4 ] or [ ¢ ]. T rack Repeat Replaying the song you are list ening to. Press the [REP] button. Each time you press the button, the Track Repeat turns ON or OFF .
English | 15 Ac cessories/ Installation P rocedure Ac cessories 1 ..........1 2 ..........2 3 ..........4 4 ..........4 5 ..........1 Installation Proc edure 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery.
16 | English ANT . CONT MUTE P .CONT FRONT • L FRONT • R REAR • L REAR • R – + FRONT Connecting W ires to T erminals FM/AM antenna input Fr ont left output ( White) (KDC-1032 only) Fr ont ri.
English | 17 Installation • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). non-Japanese cars Japanese cars 1 Ref er to the section <Removing the hard rubber frame> (page 19) and then remove the hard rubber frame.
18 | English Installation Screwing the F aceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off , screw in the provided screw s in the holes shown below . Accessory 5 • Never insert the screw in any other screw hole than the one specified.
English | 19 Removing the Unit Removing the hard rubber fr ame 1 Engage the catch pins on the r emoval tool and remove the two locks on the upper level . Upper the frame and pull it forward as shown in the figure. 2 When the upper level is r emoved, remove the lower two locations.
20 | English T roubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Befor e calling ser vice, first check the following table f or possible problems. General ? The pow er does not turn ON.
English | 21 Disc source ? The specified disc does not play , but another one plays instead . ✔ The specified CD is quit e dir ty. ☞ Clean the CD. ✔ The disc is loaded in a diff erent slot from that specified. ☞ Eject the disc magazine and check the number for the specified disc.
22 | English Specifications FM tuner section Fr equency range (200 kH z space) : 87.9 MHz – 107.9 MH z Usable sensitivity (S/N = 30dB) : 9.3dBf (0.8 V/75 Ω) Quieting sensitivity (S/N = 50dB) : 15.2dBf (1.6 V/75 Ω) Fr equency response (±3.
An important point after buying a device Kenwood KDC-1032 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kenwood KDC-1032 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kenwood KDC-1032 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kenwood KDC-1032 you will learn all the available features of the product, as well as information on its operation. The information that you get Kenwood KDC-1032 will certainly help you make a decision on the purchase.
If you already are a holder of Kenwood KDC-1032, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kenwood KDC-1032.
However, one of the most important roles played by the user manual is to help in solving problems with Kenwood KDC-1032. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kenwood KDC-1032 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
