Instruction/ maintenance manual of the product 14VF Anetsberger Brothers
Go to page of 20
1 .4 ;-4 Models 14VF 14VFS Anetsber ger Br others, Inc. 180 North Anets Drive • Northbrook, Illinois 60062 • 847-272-0770 • Fax 847-272-1943 For ANETS Factory W arranty Service • 800-837-2638 .
2 CONTENTS Shipping Container Inspection ....................................................... 3 Fryer Gas Supply Specifications .................................................... 3 Fryer Electrical Specifications .................................
3 FR YER GAS SUPPL Y SPECIFICA TIONS Please mak e sur e that your desir ed fr yer loca tion has gas supply factors that are suitable for this product: Gas Supply Inlet Pipe must be ½ “ standard gas line.
4 IMPOR T ANT : Read the Code Requir ements and ALL installation instructions car efully , befor e starting the installation. Contact the fac- tory (800/ 837-2638) if any pr oblems or ques- tions arise. The fryer installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.
5 ! Figure 2. F r yer Model 14VF/14VFS Site Installation Requirements CODE REQUIREMENTS (Continued) e. Install this fryer on a non-combustible floor with its back and sides at least 6 ” away from any combustible wall, as shown in Figure 2.
6 WARNING Fryers MUST have a movement- limiting (r estraining cable) device installed to pr event tipping that causes splashing or spilling its HOT contents. NOTE: This movement-limiting de- vice is to be furnished and in- stalled by the fr yer ’ s installing contractor before the fryer is con- nected to the gas line at its desired location.
7 INST ALLA TION REQUIREMENTS (Continued) Figure 3. Typical Leg Installation LEG LEVELING INSTRUCTIONS 1. Move the fryer to its desired location. WARNING The fryer MUST NOT tip, rock or wob- ble, to avoid splashing or spilling its HOT shortening contents during operation.
8 CASTER LEVELING INSTRUC- TIONS 1. Move the fryer to its desired location. 2. Determine whether the fryer tends to wobble or rock when in its desired location. If it does , perform steps 3 through 9. If it does not, skip to step 10, then proceed to the Installation Instructions.
9 GAS CONNECTION INSTRUCTIONS Installing your ANETS Fryer requires the fol- lowing procedure, after its legs or casters are pro- perly attached and it is in its desired location. 1. Ensure that the gas safety valve control knob in the fryer has its OFF position next to the valvemark.
10 Please observe the following recommendations to obtain the optimum results from your ANETS Fryer . D ANGER A void moving the fryer while it contains HOT shortening. Drain the shortening from the fryer before moving it for service, clean- ing or maintenance to avoid spilling or splashing.
11 Before using the newly installed fryer for food pre- paration, clean the rust preventive material from the kettle: 1 . Thoroughly wipe the interior of the kettle with clean cloths. Open the front door on the lower portion of the fryer to access the drain ball valve.
12 SHUTDOWN PROCEDURE NOTE: Shutdown is r ecommended at the end of a workday or whenever no frying is scheduled for a period of several hours. T o prevent damage, the fryer MUST also be shutdown whenever there is no shortening in the kettle. 1. T urn the thermostat knob to OFF .
13 FR YER OPERA TING INSTR UCTIONS (Continued) Load the fryer basket with the food pr oduct while the basket is not in the hot liquid shortening. DO NOT overload the fryer basket. Load only a pr emeasur ed quantity of food pr oduct ( 1½ lb , typically; less, if smaller portions ar e desir ed).
14 DAIL Y CLEANING PROCEDURE NOTE: Cleaning is recommended at the end of a workday to prepare the fryer for proper operation the next time it is to be used. D ANGER A void moving the fryer while it contains HOT shortening. Drain the shortening from the fryer before moving it for service, clean- ing or maintenance to avoid spilling or splashing.
15 NOTE: Regular maintenance is recommended to keep the fryer operating properly . Once each month, before beginning fryer opera- tion, check the flue (behind the backsplash panel) to ensure that it is clear and free of obstructions, enabling exhaust combustion gases to flow freely toward the ventilation hood area.
16 FR YER TROUBLESHOO TING GUIDE Pilot flame does not stay lighted. 1. Dirty/sooty pilot burner . 2. Low gas supply pressure [less than 6 ” W .C. for natural gas (11 ” W .C. for pro- pane) when all other gas-powered equip- ment is operating.]. 3. Pilot flame too small to heat thermo pile.
17 FR YER TR OUBLESHOO TING GUIDE (Continued) Pilot flame goes out repeatedly . 1. Low gas supply pressure [less than 6 ” W .C. for natural gas (11 ” W .C. for pro- pane) when all other gas-powered equip- ment is operating.]. 2. Loose thermocouple or high-limit thermo- stat connection(s) on gas control valve.
18 Liquid shortening does not reach the desired temperature for frying. 1. Low gas supply pressure [less than 6 ” W .C. for natural gas (1 1 ” W .C. for propane) when all other gas-powered equipment is operating], causing reduced heat from main burners.
19 NOTE: A Parts List for each ANETS Fryer is among the items shipped with each fryer. If an additional copy of this list is needed, please contact the factory as directed on the back cover . FR YER TR OUBLESHOO TING GUIDE (Continued) PROBLEM CA USE REMED Y Liquid shortening does not reach the desired temperature for frying.
20 Keep this Manual in a Convenient Location for Reference Anetsber ger Br others, Inc. 180 North Anets Drive • Northbrook, Illinois 60062 • 847-272-0770 • Fax 847-272-1943 T oll-free Customer & W arranty Service: 800/ 837-2638 Form: I-301 Rev .
An important point after buying a device Anetsberger Brothers 14VF (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Anetsberger Brothers 14VF yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Anetsberger Brothers 14VF - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Anetsberger Brothers 14VF you will learn all the available features of the product, as well as information on its operation. The information that you get Anetsberger Brothers 14VF will certainly help you make a decision on the purchase.
If you already are a holder of Anetsberger Brothers 14VF, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Anetsberger Brothers 14VF.
However, one of the most important roles played by the user manual is to help in solving problems with Anetsberger Brothers 14VF. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Anetsberger Brothers 14VF along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
