Instruction/ maintenance manual of the product J8472 Kawasaki
Go to page of 24
• Please read this manual • Please read this manual and sa ve it with y our original and save it with y our original sales receipt. sales receipt. • T ool needed for assembly: • T ool needed for assembly: Phillips Scre wdriver Phillips Screwdriver (not inc luded).
J8472a-0920 2 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 W arnings and Cautions .
J8472a-0920 3 ELECTRICAL HAZARD RIDING HAZARD • Prevent Injuries and Deaths • Direct Adult Super vision Required. • Nev er Ride at Night. • K eep Children Within Safe Riding Areas .
J8472a-0920 4 • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751 , rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.
J8472a-0920 5 PA R T S Fasteners Shown Actual Size #8 x 3 / 4 " Screw - 4 #8 x 2" Screw - 2 7 / 16 " W asher - 6 For your convenience, we included extra fasteners! Note: Tighten and loosen all screws with a Phillips screwdriver . Do not over-tighten the screws.
J8472a-0920 6 2 1 V ehicle 2 Handlebar 3 Seat 4 12 V olt Battery 5 Rear Axle 6 Rear Wheel Driver - 2 7 Wheel - 4 8 Wheel Cover - 4 9 7 / 16 " W asher - 6 10 1 3 / 8 " Cotter Pin - 4 11 Hubca.
J8472a-0920 7 ELECTRICAL HAZARD Important Notes • Y our new battery must be charged for at least 18 hours before you use it in your vehicle for the first time. • We recommend that you start charging your battery before beginning assembly of your new vehicle.
J8472a-0920 8 Children can be har med b y small par ts , shar p edges and sharp points in the vehicle's unassembled state , or b y electrical items. Care should be taken in unpac king and assembly of the v ehicle . Children should not handle par ts, including the battery , or help in assembly of the v ehicle .
J8472a-0920 9 Cotter Pin Rear Axle • Slide a 7 / 16 " washer onto the rear axle. • Slide a wheel cover , indented side down , onto the rear axle. • Locate a wheel marked L . Slide the wheel, indented side down , onto the rear axle. • Slide a bushing, barrel side down , onto the rear axle.
J8472a-0920 10 Plate • While holding the handlebar in place, carefully turn the vehicle over . • Again, make sure the end of the steering column is through the hole in the steering linkage. • Fit the steering column cap onto the end of the steering column.
J8472a-0920 11 • Fit the front clip onto the front of the vehicle, as shown. Hint: The front clip may already be on the vehicle. Front Clip FRONT VIEW 13 • “Snap” a hubcap onto the center of each wheel cover. • T urn the vehicle upright. 12 • Slide a 7 / 16 " washer onto the front axle.
J8472a-0920 12 • Fit the brush guard onto the front clip. • Insert two #8 x 3 / 4 " screws into the lower holes in the brush guard and tighten. Brush Guard 14 • Insert two #8 x 2" screws into the upper holes in the brush guard and tighten.
J8472a-0920 13 18 Seat Drive Buttons • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle.
J8472a-0920 14 RIGHT SIDE VIEW 3 11 9 16 19 8 4 7 5 6 20 21 1 10 LEFT SIDE VIEW 15 13 12 2 FOR MODEL J8472 FOR MODEL K0450 RIGHT SIDE VIEW 11 9 16 19 20 21 1 10 LEFT SIDE VIEW 12 13 15 2 3 8 4 7 5 6.
J8472a-0920 15 IMPORT ANT! Use only a Power Wheels ® 12 volt lead-acid rechargeable battery . Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 hours using the enclosed Power Wheels ® 12 volt charger before operating your vehicle for the first time.
J8472a-0920 16 • Y our Power Wheels ® battery is a non-spillable, sealed lead-acid battery . It must be recycled or disposed of in an environmentally sound manner . • Do not dispose of a lead-acid battery in a fire. The battery may explode or leak.
J8472a-0920 17 Low Speed Drive RIDING HAZARD • Pre vent Injuries and Deaths • Direct Adult Super vision Required. • Ne v er Ride at Night. • K eep Children Within Saf e Riding Areas.
J8472a-0920 18 As assembled, your vehicle is ready to roll in low speed (2 1 / 2 mph, maximum). It has been pre-set so it will only operate in low speed.
J8472a-0920 19 • Check all screws, cap nuts and their protective coverings regularly and tighten as required. Check plastic parts on a regular basis for cracks or broken pieces. • During snowy or rainy weather , the vehicle should be stored inside or under a protective cover .
J8472a-0920 20 IMPORT ANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a problem, please contact Power Wheels ® Consumer Relations, toll-free at 1-800-348-0751 between 9 AM - 7 PM (EST) Monday through Friday and 1 1 AM - 5 PM (EST) Saturday .
J8472a-0920 21 PROBLEM POSSIBLE CAUSE SOLUTION Shor t run time (Less than 1 - 3 hours per charge) Undercharged battery Charge the battery . A ne w battery should have been charged f or at least 18 hours before using the v ehicle f or the first time. After first- time use, recharge the battery for at least 14 hours after each use.
J8472a-0920 22 PROBLEM POSSIBLE CAUSE SOLUTION V ehicle r uns in lo w speed, but does not run in high speed. Please note: The v ehicle is designed to operate in low speed only in rev erse. High speed hook-up not disconnected. The vehicle w as pre-set to run only in low speed.
J8472a-0920 23 Bumper-to-Bumper* Limited W arranty One year limited warranty from the date of purchase on the Power Wheels ® vehicle. Six month limited warranty on the 12 volt battery .
PRINTED IN CHINA 73610a-0920 Or contact your local independently owned and operated Power Wheels ® Authorized Service Center . For the location nearest you, visit us on-line at www .powerwheels.com . Kawasaki and Ninja are trademarks licensed by Kawasaki Motors Corp.
An important point after buying a device Kawasaki J8472 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kawasaki J8472 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kawasaki J8472 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kawasaki J8472 you will learn all the available features of the product, as well as information on its operation. The information that you get Kawasaki J8472 will certainly help you make a decision on the purchase.
If you already are a holder of Kawasaki J8472, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kawasaki J8472.
However, one of the most important roles played by the user manual is to help in solving problems with Kawasaki J8472. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kawasaki J8472 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
