Instruction/ maintenance manual of the product 840139 Kawasaki
Go to page of 20
MODEL #840139 13" DRILL PRESS INSTRUCTION MANUAL FOR CUSTOMER SERVICE POUR LE SERVICE APRÉS VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1-800-590-3723 Printed in China 87-1904-60957 KAW ASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP .
INSERTING LASER BA TTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SECTION FOUR MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injur y . 1. KEEP GUARDS IN PLACE AND IN WORKING ORDER.
This drill press is equipped with a grounded 3-wire power cord with a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter can be used as long as it is connected to the center screw in the wall plate. See Figure 1 and the steps below to use an AC grounding adapter: 1.
9. USE ONL Y DRILL BITS, SANDING DRUMS, AND OTHER ACCESSORIES that are designed for the various speeds of this drill press. The drill bits, sanding drums and other accessories should have a shank size 1/2" OR SMALLER. Unsuitable drill bits can break without warning throwing fragments outward at high speeds possibly causing severe injuries.
30. ADDITIONAL INFORMA TION about the proper use of bench-mounted drill presses is available from the Power T ool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201.
FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. Column Base 2. Column Assembly 3. Column 4. Column Rack 5. T able Crank 6. T able Support 7. T able Crank Assembly 8.
T o minimize crank handle backlash, tighten the support lock, rotate the elevation worm shaft clockwise, assemble the crank tightly against the table support and tighten setscrew. 11.Check column collar for proper adjustment. 12.Collar should not be aligned on the column.
6. Install the setscrews in the holes on the right side of the head assembly . 7. Using a 5mm “L” hex wrench (located in the loose parts box) securely tighten the setscrews. INST ALLING BEL T GUARD KNOB T o av oi d po ssib le in ju ry , alw ay s ke ep the b elt gua rd clo sed du ri ng dri ll pr es s op erat ion .
18 17 ADJUSTING THE DRIVE PULLEYS The drive pulleys on the spindle shaft and the motor shaft may loosen during shipment. It is crucial that these pulleys are the same height on their respective shafts. Failure to square these pulleys could result in premature belt wear or damage to the motor and spindle bearings or both.
SQUARING THE WORKT ABLE The combination square must be “true” when used to square the worktable. See T ools Required for Assembly . This is essential in order to do precision drilling. 1. Insert a straight, ground steel rod, approxi- mately 3" long (not included) into the drill check and tighten.
DO NOT attempt to perform any drilling operations until the worktable is securely locked in position with the table lock clamp. Failure to lock the worktable could cause it to unexpectedly tilt causing the workpiece to bind on the drill bit.
ADJUSTING THE T ABLE HEIGHT T urn the drill press ON/OFF switch to the OFF position and disconnect the AC power to prevent drill press from accidentally turning on. 1. Loosen the table lock handle. 2. T urn the table crank handle count- er -clockwise to lower the work- table and clockwise to raise it.
SETTING THE DRILLING DEPTH ADJUSTMENT T urn the drill pre ss ON/O FF switc h to t he OFF posit ion a nd dis con nec t the AC powe r to pre ven t dril l pre ss fro m acc ide nta lly turni ng on. The drilling depth adjustment is used when more than one hole is to be drilled to exactly the same depth (i.
DRILLING THROUGH WOOD: 1. Position the workpiece so that the hole to be drilled is over the center hole on the worktable. 2. Place a piece of scrap material under the workpiece to prevent “splintering” on the bottom side of the workpiece. 3. Clamp BOTH the workpiece and the scrap material to the worktable.
NEVER LOOK INTO THE LASER BEAM. Any contact with the eyes by the beam could cause injur y . Do not use the laser when cutting reflective materials. DO NOT AIM THE LASER BEAM A T ANYONE OR A T REFLECTIVE SURF ACES. CLASS 2M LASER PRODUCT . Any contact with the eyes by the beam could cause injury .
TROUBLE PROBABLE CAUSE SOLUTION REPLACING LASER BA TTERIES The laser runs on two AAA batteries which are located beneath the “ON/OFF” switch. When the laser light begins to dim, change both batteries. NEVER mix old batteries with new. TO CHANGE LASER BA TTERIES: 1.
SPECIFICA TIONS SPECIFICA TIONS Voltage 120V 60 Hz Rated Current 6.6 A No-Load Speed (motor) 1725 RPM Max. Distance From Spindle Axis T o Sur face Of Column: 6 5/8" (170.275mm) Max. Distance From Spindle End T o Sur face Of T able: 30 3/4" (781.
item and/or part will be repaired and/or replaced. If the unit is repaired, new or reconditioned replacement parts may be used. If Alltrade chooses to replace the product, it may replace it with a new or reconditioned one of the same or comparable design.
REPRESENT A TIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO EVENT , WHETHER AS A RESUL T OF A BREACH OF CONTRACT , WAR R A N TY , T ORT ( I NC L U DI N G NE G L IG E N C E) O R O T HE R W I SE , SH A L L ALL TRADE’S AND/OR ITS REPRESENT A TIVE(S)’ LIABILITY EXCEED THE PRICE OF THE PRODUCT .
An important point after buying a device Kawasaki 840139 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kawasaki 840139 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kawasaki 840139 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kawasaki 840139 you will learn all the available features of the product, as well as information on its operation. The information that you get Kawasaki 840139 will certainly help you make a decision on the purchase.
If you already are a holder of Kawasaki 840139, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kawasaki 840139.
However, one of the most important roles played by the user manual is to help in solving problems with Kawasaki 840139. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kawasaki 840139 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
