Instruction/ maintenance manual of the product 840116 Kawasaki
Go to page of 16
8" BENCH DRILL PRESS INSTRUCTION MANUAL FOR CUSTOMER SERVICE POUR LE SERVICE APRÉS VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1-800-590-3723 Printed in China 87-1904-60957 KAW ASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP .
SECTION FOUR MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26 SPECIFICA TIONS . . . . . . . . . . . . . . . .
GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS RE AD AN D UND ER ST AND ALL INS TRUC TIO NS . Fa il ur e to fol lo w all ins tru ct io ns li st ed bel ow ma y re sult in ele ct ri c sh ock, fi re and /o r se rio us per so na l in jury . KEEP GUARDS IN PLACE AND IN WORKING ORDER.
This drill press is equipped with a grounded 3-wire power cord with a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter can be used as long as it is connected to the center screw in the wall plate. See Figure 1 and the steps below to use an AC grounding adapter: 1.
USE ONL Y DRILL BITS, SANDING DRUMS, AND OTHER ACCESSORIES that are designed for the various speeds of this drill press. The drill bits, sanding drums and other accessories should have a shank size 1/2" OR SMALLER. Unsuitable drill bits can break without warning throwing fragments outward at high speeds possibly causing severe injuries.
SECURE THE ELECTRICAL POWER CORD when the drill press is not in use to prevent unauthorized use of the tool and/or to prevent children from acciden- tally turning it on. ADDITIONAL INFORMA TION about the proper use of bench-mounted drill presses is available from the Power T ool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www .
FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. Drill Bit 2. Column Assembly 3. Feed Handles 4. Chuck Key 5. Drill Chuck 5. Head Assembly 6. Knob (and mtg Hardware) 7. Work T able ASSEMBL Y Do not begin assembly of Bench-mounted Drill Press if the AC power cord is plugged into an AC power receptacle.
Ensure the spindle taper (Q) and the tapered hole in the drill chuck (R) are clean and free of any grease, lacquer , or rust preventative coatings. These compounds can cause the drill chuck (R ) to seize when installed on the spindle shaft (Q). INST ALLING THE DRILL CHUCK 1.
LASER GUIDE Use of controls or procedures, or performance of proce- dures other then those specified herein may result in hazardous radiation exposure. LASER SAFETY NEVER LOOK INTO THE LASER BEAM. Any contact with the eyes by the beam could cause injury .
17 18 STORE OUT OF REACH OF CHILDREN. Equipment should be in a high location or locked up to keep out of reach of children. It is not a toy . DO NOT T AMPER WITH THE LASER OUTPUT . Changing the performance of the laser to increase its output is prohibited.
Ensure that the switch toggle, when removed, is kept in a secure place. Once removed, the drill press will not start without it. ADJUSTING THE WORK T ABLE 1. The worktable (1) can be raised or low- ered on the drill press column (2) by loosening the table clamp (3).
1. Lift up the pulley cover (1). 2. Release the belt tension by loosen- ing the tension lock knob (2) located on the side of the drill press head. Loosen the tension lock knob (2) by turning it counterclockwise. 3. Pivot the motor (3) towards the front of the drill press.
3. T urn the spring housing (5) counter- clockwise to increase the spring ten- sion or clockwise to decrease the spring tension. 4. T urn nut (4 - inside) until it contacts the spring housing (5). Back nut (4) out 1/4 turn and tighten it against nut (3 - outside) to hold the spring housing in place.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. I f t h e d r il l p r es s mu s t b e us e d o u ts id e , u s e a n ex t en si o n c o rd l a be l e d “ W - A ” o r “W .
Warranty Performance By pur chasing the product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replace.
ALL TRADE AND/OR ITS REPRESENT A TIVE(S), OR THE PURCHASER, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANT ABILITY AND THE W AR RA NTY OF FI TN ES S FOR A P AR TI CU LA R PUR POS E, AR E HER EB Y EXP RESS L Y EXCLUDED AND DISCLAIMED BY ALL TRADE AND/OR ITS REPRESENT A TIVES.
An important point after buying a device Kawasaki 840116 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kawasaki 840116 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kawasaki 840116 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kawasaki 840116 you will learn all the available features of the product, as well as information on its operation. The information that you get Kawasaki 840116 will certainly help you make a decision on the purchase.
If you already are a holder of Kawasaki 840116, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kawasaki 840116.
However, one of the most important roles played by the user manual is to help in solving problems with Kawasaki 840116. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kawasaki 840116 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
