Instruction/ maintenance manual of the product K1-UC-S K2 Mounts
Go to page of 20
1 T able of Contents Before Y ou Begin 2 K1-F-S Installation 3 K1-TS-S & K1-A1-S Installation 6 K2-A1-S Installation 1 1 K1-UC-S (Under-Cabinet Mount) Installation 15 Specications 19 K1 & K2 Series Manual 6.
2 3 Before Y ou Begin STOP Do not attempt to install this product if you do not understand the instructions or if there are missing or defective parts.
2 3 K1-F-S Installation Instructions Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown.
4 5 Attach the W all Plate to the W all ! Concrete anchors are not provided. T o mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury .
4 5 Attach the Screen to the W all Plate 1. Push the screen plate against the wall plate and then let it slide down into place. 2. Fasten the screw through the screw hole in the bottom of the bracket until it seats against the nut. K1 & K2 Series Manual 6.
6 7 K1-TS-S & K1-A1-S Installation Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown.
6 7 Attach the W all Plate to the W all ! Concrete anchors are not provided. T o mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury .
8 9 Assemble the Arm ( K1-A1-S only) 1. Assemble the arm, and attach it to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 8.
8 9 Attach the Screen to the W all Plate Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. The K1-TS-S is pictured to the right. The K1-A1-S is pictured on the next page. K1 & K2 Series Manual 6.0W X 4 R1.
10 1 1 K1-A1-S Attachment K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 10.
10 1 1 K2-A1-S Installation Instructions Attach the Screen Plate to the Screen ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen plate on the screen as shown.
12 13 Attach the W all Plate to the W all ! Concrete anchors are not provided. T o mount to a brick or concrete wall, purchase concrete anchors to accomodate the provided screws. ! When mounting to a drywall or plaster wall, you should attach the wall plate to a 2X4 or larger wood stud to avoid property damage or personal injury .
12 13 Assemble the Arm 1. Assemble the arm, and attach it to the wall plate. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 13.
14 15 Attach the Screen to the Arm Using the included inside hex and outside hex wrenchs, attach the screen to the wall plate. K1 & K2 Series Manual 6.
14 15 K1-UC-S (Under-Cabinet Mount) Installation Drill the Mounting Holes 1. Remove the contents of your cabinet. 2. Hold the bracket under the cabinet where it will be mounted. 3. Insert a pen or pencil through the mounting holes and make marks where you need to drill.
16 17 Attach the Front Cap Piece 1. Slide the cap piece onto the bracket as shown. K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 16.
16 17 Attach the Mount to the Cabinet 1. Insert four mounting screws down through the holes drilled earlier . 2. Place a spacer on each screw between the cabinet bottom and the top of the mount. 3. T ighten the screws down into the mount holes using the provided hex wrench.
18 19 Attach the Screen to the Mount ! Caution: With the screen plate in place, test the screw length to ensure that they do not extend past the screen hole depth and damage the screen. 1. Position the screen on the screen plate as shown. 2. Attach the plate with the original screen screws.
18 19 Specications ! Caution: These mounting brackets are intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in instability and cause injury . Model VESA Support T ilt Range Ext.
20 K1 & K2 Series Manual 6.0W X 4 R1.indd 12/15/2005, 8:57 AM 20.
An important point after buying a device K2 Mounts K1-UC-S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought K2 Mounts K1-UC-S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data K2 Mounts K1-UC-S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, K2 Mounts K1-UC-S you will learn all the available features of the product, as well as information on its operation. The information that you get K2 Mounts K1-UC-S will certainly help you make a decision on the purchase.
If you already are a holder of K2 Mounts K1-UC-S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime K2 Mounts K1-UC-S.
However, one of the most important roles played by the user manual is to help in solving problems with K2 Mounts K1-UC-S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device K2 Mounts K1-UC-S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
