Instruction/ maintenance manual of the product HP3A K-Tec
Go to page of 17
Model HP3A Instruction Manual.
.
T able of Contents SECTION P AGE # SECTION 1: IMPORT ANT SAFEGUARDS 1 SECTION 2: UNP ACKING 3 SECTION 3: BLENDER OVERVIEW 4 SECTION 4: INST ALLA TION 4 SECTION 5: CARE AND CLEANING 6 SECTION 6: OPERA .
HP-1 SECTION 1 IMPORT ANT INFORMA TION Read all instructions carefully before using your Blender™ 1.1 SAFETY CERTIFICA TION The blender is certied by ETL (Report No. 3018204-4, 3018204-2 & 3018204-3). 1.2 CERTIFICA TION Blender and its accessories are certied by NSF International (NSF), under K-TEC in the NSF Ofcial Listing.
HP-2 1.8 NEVER OPERA TE THE BLENDER USING A TT ACHMENTS NOT SOLD BY BLENDTEC The use of any unauthorized attachments may cause re, electric shock, and/or injury and will void the warranty . 1.9 CONT AINER MUST BE PROPERL Y IN PLACE WHILE APPLIANCE IS OPERA TING 1.
HP-3 SECTION 2 SA VE ALL P ACKAGING MA TERIALS AND INSTRUCTIONS FOR FUTURE USE. 2.1 UNP ACKING YOUR BLENDER Y ou should have received the following items: • Motor base • Blender jar with lid • Recipe book 1. Remove blender motor , blender jar and lid from packaging.
HP-4 SECTION 3 Blender OVERVIEW (Refer to Figures 1 and 2) 3.1 BLENDER MOTOR • Motor Cover: Houses the power unit in a durable, easy-to-clean polycarbonate. • T ouch Pad: Consists of six buttons that contain pre-programmed settings for selective blender control, a pulse button, and two speed control buttons.
HP-5.
HP-6 SECTION 5 CARE AND CLEANING 5.1 AFTER USE CLEANING 1. Add 1 cup of hot water and a drop of liquid dishwashing soap to the blender jar . 2. Place the lid tightly onto the jar . Place the blender jar on the blender base, and with your hand placed on top of the lid; press the pulse button for 5 seconds.
HP-7 SECTION 6 OPERA TIONAL OVER VIEW Y our Blendtec home blender has 30+ pre-programmed blend cycles for your con- venience, or optional manual controls. A representation of the controls is found below: 6.1 BEFORE YOU BEGIN OPERA TION 1. T urn on the main power switch located on the back of the blender motor in the lower right corner .
HP-8 6.3 AUTOMA TIC AND CUSTOM CONTROLS PRESETS: The four numbered buttons on the left side of the touchpad oper- ate four customizable pre-selected blend cycles. T o select one of these presets simply press the designated button. SELECTING A CYCLE FROM THE CYCLE MENU: T o access the Cycle Menu press the SELECT CYCLE MENU button.
HP-9 6.4 RESTORING F ACTOR Y DEF AUL TS The Blendtec home blender has the following cycles set as factory defaults: BUTTON # CA TEGORY CYCLE NAME 1 Multi-Use Low Energy 2 Beverages Smoothie 3 Drinks/I.
HP-10 SECTION 7 TROUBLESHOOTING 7.1 BLENDER MOTOR WILL NOT TURN ON If the blender motor will not turn on, try the following: • Make sure the main power switch on the back lower-right corner is turned ON. • Check your house circuit breaker switch or fuse, to make sure it is set to the ON position.
HP-1 1 7.3 BLENDED TEXTURE UNSA TISF ACTOR Y If the blended texture of product is lumpy or uneven, do the following: • Ensure the mixture is not cavitating during the cycle. Cavitation is a condi- tion in which the blender blade spins freely in an air pocket within the drink mix because the mix is too cold or too solid.
HP-12 SECTION 8 W ARRANTY W ARRANTY DESCRIPTION (US Domestic and Canada) Y our Blendtec Blender motor is warrented for 3 years or 10,000 cycles, which- ever happens rst. The jar assembly , including all moving jar parts, is covered against leaking or breakage for 1 year .
HP-13 UNDER W ARRANTY 1. Contact Blendtec immediately to diagnose the difculty . Please have blender serial number ready as well as a description of the problem. Do not attempt to do your own repairs. Repairs made by persons other than Blendtec authorized service representatives will void the warranty .
HP-14 1206 South 1680 West Orem, UT 84058 801-222-0888 blendtechome.com OWN-RE-023 Model HP3A Manual Rev . 02 12/06 ©2006 K-TEC, Inc., All Rights Reserved Blendtec is a registered trademark of K-TEC, Inc.
An important point after buying a device K-Tec HP3A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought K-Tec HP3A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data K-Tec HP3A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, K-Tec HP3A you will learn all the available features of the product, as well as information on its operation. The information that you get K-Tec HP3A will certainly help you make a decision on the purchase.
If you already are a holder of K-Tec HP3A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime K-Tec HP3A.
However, one of the most important roles played by the user manual is to help in solving problems with K-Tec HP3A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device K-Tec HP3A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
