Instruction/ maintenance manual of the product VN-X235U series JVC
Go to page of 85
IP CAMERA VN-V25U VN-V26U VN-X35U VN-V225U series VN-X235U series INSTR UCTIONS (Setting) LST0886-001A Thank you f or purchasing this JVC product. Bef ore operating this unit, please read the instructions carefully to ensure the best possible perf ormance.
2 Getting Start ed Getting Star ted Contents ................................................... 2 Network Setting s Network Requirements ............................. 3 IP Address Settings .................................. 6 IP address setting procedure.
3 Network Settin gs ● Ensure that the re is sufficient ne twork bandwidth f or the data vo lume to be sent out by camera . Do not send mult icast stream tha t exceeds the bandwidt h. If the entire bandwidth is used by the multicast str eam, control of this camera via the n etwork may fail.
4 Network Settin gs Bit Rate of Audio Only 1 audio data stream can be received. Data v olume for 1 audio stream is 64 kbps . Audio data v olume may be calculated using the follo wing formula.
5 ● When both JPEG and MPEG4 images are distributed When both JPEG and MPEG4 images are distributed, distribution works in the same way as frame rate priority mode if the distribution request would be accepted in the frame rate priority mode.
6 Network Settings IP address setting procedure Follo w the procedure below to configure the IP address of the camera. Step1 IP address setting at the computer ( A Pag e 7 ) G Step2 Internet Explorer .
7 IP address setting at the c omputer Set the computer to an IP address that enables communication with the camera. Procedures described in this item are intended for Windows XP users . 1. Click [Start] ● Select in the sequence o f [Control Panel] - [Network Connection] - [Local Area ].
8 Network Settin gs Internet Explorer Setting 1. Launch the Internet Explorer on the co mputer 2. When proxy settings are enabled in the In ternet Explorer, follow the step s below to disable the prox.
9 4. If ActiveX controls and plug-ins of the Internet Exp lorer is disabled, follow the steps below to enable it ● Click [Trusted sites] under [Tool] - [Internet Options] - [Security]. Select the [Custom Le vel] button and open the [Security Settings] window.
10 Network Settings Connecting the came ra to the computer 1. Launch the Internet Explorer Memo: ● If the proxy server settings for access to the Inte rnet via the I nternet Ex plorer is enabled, you may not be able to specify the IP address directly.
11 3. Built-in Viewer of camera is displayed 4. The operator password entry screen app ears A Enter the password (default is A jvc B ) of A operator B authority. B Click [OK]. Memo: ● The operator password entry screen does not appear if the password is stored on t he computer.
12 Network Settings IP address setting for the camera 1 Click [Details] of the camera Built-in viewer 2 The [Basic Settings1] screen appears A Set the [IP Setting]. ● When selecting A DHCP Disable B : Select A DHCP Disable B , and specify a v alue in the [IP Address], [Subnet Mask] and [Default Gateway] fields.
13 B Select the [Time Zone]. C Click [OK]. 3 A confirmation screen appears Click [OK]. Camera restar ts using the new IP address. It tak es about one minute for the camera to reboot. Memo: ● Access from the connected computer may fail wh en the IP address of the camera is changed.
14 Network Settings E nter user name and password User name and passw ord entr y will be required at the beginning. There are three access authorization levels to camera . The factory settings are as follo ws. 䢇 Pages that users have access to Restrictions are placed on the page s that users hav e access to.
15 ● operator ( T X) is applicable to VN-X series only . ● user Memo: ● The [Security Se ttings] screen appears before the top page is displayed. Press the [Yes] button to proceed. If you do not want this warning screen to be displayed, change the Internet Explorer settings as follows.
16 Setting Using Internet Explorer How to open the setting page 1. Enter IP address of camera in the ad dress bar of Internet Explorer ( A Page 10) A unified view er is opened. 2. Click [Details]. ● [Basic Settings1] pag e will be opened if a ccessed by user name A admin B .
17 Basic Settings1 This page is for perf or ming basic setting related to the networ k. This page can be used during access using A admin B . ● Click [Basic Settings1].
18 Setting Using Internet Explorer Basic Settings2 P age for setting fundamental parameters of A Camera B , A JPEG B and A MPEG4 B . This page can be used during access using A admin B or A operator B . ● Click [Basic Settings2]. ● Press the [OK] button to enable the new settings.
19 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . A Camera ID Character strings entered here will be wr itten to the JPEG comment segment (item name: camera).
20 Setting Using Internet Explorer Basic Settings2 (continued) ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Setting (continued) D JPEG F rame Size For specifying the JPEG picture quality (rat e control mode) and siz e (target file size).
21 Camera Page This page is for setting the camer a’ s parameters. This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to display setting menu. ● Click [Camera]. ● Press the [OK] button to enable the new settings.
22 Setting Using Internet Explorer ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Setting (continued) A Camera ID Character strings entered here will be wr itten to the JPEG comment segment (item name: camera). Refer to the API Guide on the file f or mats of JPEG.
23 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . G Color Level For adjusting the color lev el. Larger value : Increases the color level. Smaller value : Decreases the color level. [Setting values: -5 to 0 to 5] H AGC For setting the A GC (auto matic gain control) lev el.
24 Setting Using Internet Explorer Camera Page (continued) ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Setting (continued) K Shutter Speed For setting the shutter speed. Auto, Auto(1/15 - 1/1 00) : Varies the shutter speed automatically acco rding to the brightness.
25 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . M EV Compensation F or setting EV (Exposu re V alue) correction. E nables setting between -9(-3EV) to 6(+2EV). Y ou can specify settings in each 1/3 EV step. Decreasing the value darkens the images, while increasing t he value brightens the ima ge.
26 Setting Using Internet Explorer Encoding Page This page is for setting JP EG and MPEG4 encoding parameters. This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to display setting menu. ● Click [Encoding].
27 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . A Frame Size Fo r selecting the fr ame size of each JPEG or MPEG4 screen to Quad V G A (1280 ⳯ 960) ( T X), V GA (640 ⳯ 480) or QV GA (320 ⳯ 240). Select one of the four ( T V) or eight ( T X) different patter ns.
28 Setting Using Internet Explorer Audio Page (This feature is not a vailab le in VN-V25U) This page is for setting the audio par ameters. This page can be used during access using A admin B or A operator B ● Click [Advanced Settings] to display setting menu.
29 A Duplex Mode F or setting the audio transmission method. When half duplex is selected, audio sent to computers from th e camera is muted when audio is transmitted from a computer to the camera. When full duplex is selected, y ou c an send audio to the camera from a computer while listening to audio s ent to computers from the camera.
30 Setting Using Internet Explorer Alarm Page This page is for setting actions when there is an alarm. Up to 5 actions (No . 01 to No. 05) ma y be set. This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to displ ay setting menu.
31 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . A Action For specifying the type of action. Disable : Does not trigger any action. Mail : Send s out e-mail. Specify the recipient’s mail address. The title of the mail will appear as [Alarm from A model name B ] (E.
32 Setting Using Internet Explorer Alarm Page (continued) ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Setting (continued) B 1st Trigger For specifying the first trig ger to be a ctivated.
33 H Mail Mail Address : For entering th e recipient’s mail address. Mail Text : For entering the mail transmission data. Input up to 127 alphanumeric characters.
34 Setting Using Internet Explorer Alarm Environment Page This page is for setting alarm-related environments . This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to display setting menu. ● Click [Alarm Environment].
35 A Mail For setting the mail environment when [M ail] is specified as an action on the Alarm page.[SMTP] and [POP] can be used. Configure only the [SMTP] settings under usual circumstances. Enter the camera’ s mail address as the recipient’ s mail address.
36 Setting Using Internet Explorer Alarm Environment Page (continued) Setting (continued) C B.
37 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . B FTP (continued) Time Filter: For specifying the periodic FTP transf er action with respect to each day of the week and setting the corresponding time of the day .
38 Setting Using Internet Explorer PTZ P age (VN-X series only) Set the mov ement for A A uto Retur n B , A Zoom Limit B and A Preset Position B . This page can be used during access using A admin B or A operator B . ● First of all, configure the encoding settings.
39 A uto Patr ol Page (VN-X series only) P erform Auto P atrol setting to switch image displa y bet ween multiple positions according to the in terval that has been set. Set when viewing registered positions in order . This page can be used during access using A admin B or A operator B .
40 Setting Using Internet Explorer Auto Patrol Pa ge (continued) (VN-X series only) Setting (continued) C B A DE Clic k A No. Switches the camera images in sequence from No. 0 to No . 19. B Title Shows the title of the position. C Po s i t i o n For setting the sequence of position numbers in which the camera mo ves .
41 Privacy Mask Page Privacy Mask is a f eature that enable s masking of a por tion of the image. The camera enables unlimited privacy masks to be spec ified in diff eren t shapes at your fa vorite locations. The Privacy Mask masks area by uploadi ng a BMP file painted in red (created separately).
42 Setting Using Internet Explorer Privacy Mask Page (continued) ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Setting (continued) A Mode For specifying whether to activ ate the Privacy Mask feature . When this is set to A On B , the pr ivacy mask specified using the f ollowing items will appear on the image.
43 Motion Detection Page This page is for setting motion detection. This page can be used during access using A admin B or A operator B . Memo: ● When images on the camera are currently acquired by .
44 Setting Using Internet Explorer Motion Detection Page (continued) Memo: ● The area display position serves as a re fe rence. Make sure to perform operation check.
45 Network Basic Pa ge This page is for perf or ming basic setting related to the networ k. This page can be used during access using A admin B . ● Click [Advanced Settings] to display setting menu. ● Click [ Network Basic ] . ● Press the [OK] button to enable the new settings.
46 Setting Using Internet Explorer Network Details P age This page is for perf or ming detailed networ k setting. This page can be used during access using A admin B . ● Click [Advanced Settings] to display setting menu. ● Click [ Network Details ] .
47 Protocol Page This page is for changing the HTTP server por t number . This page can be used during access using A admin B . ● Click [Advanced Settings] to display setting menu. ● Click [ Protocol ] . ● Press the [OK] button to enable the new settings.
48 Setting Using Internet Explorer Streaming Page This page is for setting man ual m ulticast transmission. This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to display setting menu. ● Click [ Streaming ] .
49 Memo: ● When the power of the camera shuts down accident ally during multicast transmission, multicast transmission will restart automatic ally after the camera is rebooted. ● When the setting on the Encoding page is set to a pattern where MPEG4 is not available, MPEG4 multicast transmission cannot start.
50 Setting Using In ternet Expl orer Access Restrictions Page (VN-V25U does not have audio.) This page is for setting client restrictions. This page can be used during access usin g A admin B . ● Click [Advanced Settings] to display setting menu. ● Click [Access Restrictions].
51 Note: ● Note that when A allow B is selected and all IP address fields are left blank, JPEG / MPEG4 / Audio acquisition by all IP addresses will be denied. Restrictions are not imposed on access to the Web Settings page. Additionally, Camera will also deny access when instructions for tran smission to the specified IP address are sent via API.
52 Setting Using Internet Explorer Time Page This page is for setting time . This page can be used during access using A admin B . ● Click [Advanced Settings] to display setting menu. ● Click [ Time ] . ● Press the [OK] button to enable the new settings.
53 Password Page This page is for setting the pass word. This page can be used during access using A admin B . ● Click [Advanced Settings] to display setting menu. ● Click [ Password ] . ● Press the [OK] button to enable the new settings. Note: ● Be sure to handle the password carefully in case you forget it.
54 Setting Using Internet Explorer Maintenance Page This page is for maintenance purposes. This page can be used during access using A admin B . ● Click [Advanced Settings] to display setting menu. ● Click [ Maintenance ] . Setting (continued) A B C Click A Restart Restar ts the camera.
55 LED State Page This page is for setting the method f or lig hting the [ST A TUS] indicator on this camera. This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to display setting menu. ● Click [ LED State ] .
56 Setting Using Internet Explorer List of Factory Settings of Each Page ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only .
57 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . 䡵 Alarm Page ( A Page 30) 䡵 Alarm Environment Page ( A Page 34) 䡵 PTZ Page ( T X) ( A Page 38) 䡵 A uto .
58 Setting Using Internet Explorer List of Factory Settings of Each Page (continued) ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only .
59 Miscellaneous Page This page is for acquiring inf or mation. This page can be used during access using A admin B , A operator B and A user B . ● Click [Advanced Settings] to display setting menu. ● Click [ Miscellaneous ] . A Click A Open Source Software Press the [Show] button to displa y information of the software used by the camera.
60 Setting Using Internet Explorer Operation Page Displays the oper ating status of the camera. This page can be used during access using A admin B or A operator B .
61 Settings Page Display the v ersion information and current settings of the camera. This page can be used during access using A admin B or A operator B .
62 Setting Using Internet Explorer Settings Page (continued) Setting (continued).
63.
64 Setting Using Internet Explorer P o sition List (VN-X series only) The P osition List displays inf o r mation on the preset positions. This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to display setting menu.
65 Pa trol Settings (VN-X series only) P atrol Settings displays the A uto Patrol inf or mation and settings. This page can be used during access using A admin B or A operator B . ● Click [Advanced Settings] to display setting menu. ● Click [ Patrol Settings ] .
66 Operation This product comes equipped with built-in viewer . ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Y o u can star t up Built-in Viewer b y entering the IP address in the Inter net Explorer .
67 Memo: ● The settings of Built-in Viewer ar e stored in the file named Cookie. Searching and deleting cookie files ● Open [T ool] - [Internet Options] - [Advanced] of the Inter net Explorer, and press the [Settin gs] button under [T emporary Inter net Files].
68 Operation lmage Settings Below are pr ocedures for configuring the Image Settings. ● When a different men u is currently being displa y ed, click [Control] to switch the men u. ● Click each menu bar on the left of the screen to open the setting screen.
69 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . B Bac k Light Compensation For selecting the bac klight compensation feature. Set this f eature when there is a bright light source in the same direction as the object.
70 Operation PTZ Settings (VN-X series only) This page describes procedures for setting the preset positions. ● This page can be used duri ng access using A admin B or A operator B . T o access this setting, you need to set the passw ord of A operator B authority .
71 A Preset P osition For setting the preset positions. Po s i t i o n For selecting a A Po s i t i o n B . [Set values :HOME , 1 to 19] Title Displa ys the current title. Enter accordingly if you want to register or change a title. (Y ou can enter up to 32 alphanumeric or 16 Japanese characters .
72 Operation PTZ Control (VN-X series only) Use this item to operate the PTZ feature . Se ttings can be configured on the PTZ Sett ings . ( A P a ge 70) ● This page can be used duri ng access using A admin B or A operator B . T o access this setting, you need to set the passw ord of A operator B authority .
73 A A UTO F UNCTION Star t : Star ts the Auto P atrol operation. Stop : Stops the A uto Patrol oper ation that is currently ru nning. B Preset Po s i t i o n For selecting a Preset P osition, or move to the selected P osition if that P osition has already been registered.
74 Operation JPEG Viewer Settings ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Using the compressed J PEG format enables display of a series of still images as well as one-shot recording of still images.
75 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . 䡵 Stream Settings F or specifying settings for receiving JPEG stream. A Stream F or selecting the protocol when th e viewer acquires data from the camera. When A HTTP B is selected, lost packets are recov ered via resending.
76 Operation MPEG4 Viewer Settings Using the compressed MPEG4 format enables displa y of MPEG4-enco ded motion images. ● When a different men u is currently being display e d, click [Vie wer Setup] to switch the menu. ● Click the menu bar on the left side of the screen to open the respective setting screens .
77 ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . 䡵 Title Bar For setting display items on the vie wer screen. For the MPEG4 Vie wer, characters are displa yed in the title bar of the window . A Camera ID Select A On B to display [Camer a ID].
78 Operation A udio Monitor Settings (This feature is not a vailab le in VN-V25U) This page describes procedures for configuring the settin gs to send/receive audio sound using the JPEG and MPEG4 Viewers . ● This page can be used duri ng access using A admin B or A operator B .
79 䡵 Receive For specifying settings related to receiving of audio sound sent from the camera. A Receive For specifying whether to receiv e audio sound. Select A On B to receive audio sound. B Stream For selecting the stream f ormat of the received audio sound.
80 Operation Operator Pass wor d ( T V) is applicable to VN-V series only . ( T X) is applicable to VN-X series only . Follo w the procedures below to configure the oper ator pass word required fo r sending/receiving audio sound or PTZ operation. ● This page can be used duri ng access using A admin B or A operator B .
81 Exiting the Viewer T o e xit, press the [ ⳯ ] button at the top right of the window . Memo: ● During the next startu p of the built-in view er , launch the Inter net Explorer and enter the UR L of the built-in view er in the address field. For e xample, if the IP address of the camera is 192.
82 Other s T r oubleshooting Symptom Causes and Countermeasures Reference Pag e IP address of the camera is unknown ● The default IP address is 192.168.
83 Symptom Causes and Countermeasu res Reference Pag e Multicast images cannot be play ed back ● Star t multicast transmission manually from the [Streaming] page of the camera.
84 Other s T r oubleshooting (continued) Symptom Causes and Countermeasures Reference Pag e The MPEG4 Viewer screen appears in blac k When DirectX 9.x or Windows Media Play er 9.x is installed on the computer , the video image screen appears in blac k.
© 200 9 Victor Comp a ny of J a p a n, Limited LST0886-001A IP CAMERA.
An important point after buying a device JVC VN-X235U series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC VN-X235U series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC VN-X235U series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC VN-X235U series you will learn all the available features of the product, as well as information on its operation. The information that you get JVC VN-X235U series will certainly help you make a decision on the purchase.
If you already are a holder of JVC VN-X235U series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC VN-X235U series.
However, one of the most important roles played by the user manual is to help in solving problems with JVC VN-X235U series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC VN-X235U series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
