Instruction/ maintenance manual of the product VN-V235U JVC
Go to page of 18
FIXD IP DOME CAMERA FIXD MEGAPIXEL IP DOME CAMERA VN-V225U VN-X235U INSTR UCTIONS (Installation) LST0926-001A ● This is a supplementar y instruction manual to [READ ME FIRST]. Please read through this manual together with the bundled [READ ME FIRST] (sheet).
2 Getting Started High picture quality The camera emplo ys a progressiv e CCD with a resolution of about 330,000 pixels (1/4"), which enables video surveillance using high-quality images. (VN-V225U) The camera emplo ys a progressiv e CCD with a resolution of abo ut 1.
3 Analog signal output (for i nstallation) This camera is equipped with an analog video monitor signal output terminal, which is used f or adjusting the camera angle during installation. Saving JPEG images to the FTP server at regular intervals JPEG images may be uploaded to the FTP server at regular inter v als.
4 Getting Started Storage and Operating En vironment 䢇 This product is an indoor camera. It cannot be used outdoors. 䢇 Do not store in the following en vironments.
5 Others 䢇 This camera comes with a built-in A GC circuit. Setting AGC to A Mid B , A High B or A Super B increases the sensitivity of a dark image, and the screen may appear g rainy .
6 Getting Started Camera A Mounting holes (oval) ⳯ 4 Use these holes when mounting the camera directly to the ceiling or a wall. B Mounting h oles (r ound) ⳯ 4 Use these holes when mounting the camera directly to the ceiling or a wall. They are also used f or mounting the camera to an electrical box.
7 Camera Body/Interio r T The follo wing is an illustration when the dome cover , inner dome, and outer casing are remov ed. Remov al procedures ( A page 11 A Remove the outer casing B ) H [10BASE-T/100B ASE-TX(PoE)] LAN cable connector (RJ-45) I Fall prevention sheet This sheet connects th e camera unit with the dome cov er .
8 Getting Started Lens Q Tilt fastening screw Note: ● After adjusting the field angle, tighten the tilt fastening scre w to secure the camera so that its field angle does not go out of alignment. ( A [READ ME FIRST]) R Focus adjustment ring Mov e the ring to th e left and right to adjust the foc u s.
9 V Status indicator Indicates the current status of the camera. Star ting up : Lights up in orange After star tup is complete : Lights up in green Error : Blinks in orange Memo: ● When the camera is in the focus adjust mode, the status indicator blinks in green and orange alternat ely .
10 Connection/Installation Selecting a Mounting Method The procedures vary according to the mount ing method. Mount the camera accordingly by referring to the respective section. Note: ● Be sure to put on protective glasses to protect your e yes from f alling objects when mounting the camera to the ceiling.
11 4 Remove the inner dome The inner dome is fastened using 2 catches. Remov e the inner dome by unf astening it from the catches. 5 Remove the outer casing (This mounting method does not make use of an outer casing.
12 Connection/Installation 䡵 Mounting 1 Align the shooting direction with the shooting direction mark ( j ), followed by mounting the camera 2 Fasten the camera (x3 locations) A T ur n the tip of th.
13 Alarm Input Connect the cable to sensors such as infrared sensors, door sensor s, metal sensors and manual s witches. 䡵 Input Requirements ● Non-voltage rela y NPN open collector input ● P ol.
14 Other s T roub leshooting Symptom Causes and Counterm easures Images are not output to the monitor ● Set the [MONIT OR OUT] selection switch to A N B or A P B , and press the Reset button. ● When using the [MONITOR] output, set the privacy mask to A Off B .
15 CAMERA HEAD Image pickup de vice VN-V225U : 1/4" square pixel progressiv e-scan CCD (complementar y filter) VN-X235U : 1/3" square pixel progressiv e-scan CCD (complementar y filter) Eff ective pix els VN-V225U : Appro x. 330,000 pixe ls 659 (H) ⳯ 494 (V) VN-X235U : Appro x.
16 Other s Overall Alarm input ⳯ 2 : No-voltage a contact input, NPN open collector input, low-le vel input, latch/ momentar y (500 ms and abov e) input (circuit current during low-lev el input: 1 mA; applied voltage during high- le vel input: DC 3.
17 Dimension [Unit: mm (inches)] T Specifications and appearance of this unit are subject to change f or fur ther improv ements without prior notice..
© 200 9 Victor Comp a ny of J a p a n, Limited LST0926-001A VN-V225U/VN-X235U FIXD IP DOME CAME RA / FIXD MEGAPIXEL IP DOME CAMERA.
An important point after buying a device JVC VN-V235U (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC VN-V235U yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC VN-V235U - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC VN-V235U you will learn all the available features of the product, as well as information on its operation. The information that you get JVC VN-V235U will certainly help you make a decision on the purchase.
If you already are a holder of JVC VN-V235U, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC VN-V235U.
However, one of the most important roles played by the user manual is to help in solving problems with JVC VN-V235U. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC VN-V235U along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
