Instruction/ maintenance manual of the product TK-T2101RU JVC
Go to page of 16
FIXED IR DOME CAMERA TK - T2101RU FIXED IR DOME CAMERA TK - T2101RE Instructions.
.
1 Important Safety Information Warning and Operating Notes Installation and serving the camera should be performed only by qualied and experienced technicians to conform to all local codes and to maintain your warr anty .
2 T ABLE OF CONTENTS 1. Introduction .................................................................................. 3 1.1 Before Y ou Begin ----------------------------------------------------------------- 3 1.2 Dimensions ----------------------------------------------------------------------- 3 1.
3 INTRODUCTION 1. Introduction The dome camera is ideal for indoor installation in commercial and residential environment. With 3-axis mount support, it pro vides exible installation on a ceiling or wall even at an angle. 1.1 Before Y ou Begin Please read this manual carefully before you install the dome camer a.
4 1.3 Names of Camera Parts a b Figure 1-1 Camera parts 1. Conduit hole used for surface run power/video connector 2. Bottom case 3. Camera housing 4. Dome cover 5. IR board a. AC 24V / DC 12V power input connector (red +, black -) b. Video output connector Note: See Figure 2-3 for camera board controls.
5 INST ALLA TION 2. Installation 2.1 Disassembling the Camera Before you mount and adjust the camer a, follow these steps to disassemble the camera. 1. Insert a coin or at tool to the side hole and twist to remove the dome co ver . 2. Remo ve the dome cover (#2).
6 INST ALLA TION 2.2 Connecting the wiring Refer to Figure 1-1 to connect the video connect output connector (#b) and 24 VAC/12 VDC power connector (#a). Caution: For DC power supply use, mak e sure the polarity is correct to avoid malfunction and / or camera damage.
7 INST ALLA TION 2.4 Optional Camera Settings Refer to Figure 2-3 to locate the OSD jo ystick control on the camera board. Use the joystick to access the OSD menu and congure the camer a settings as required. T o use the OSD joystick control: • Press the OSD joystick control straight down to enter the Main menu or a selected item.
8 2.5 Adjusting the Camera Position The dome camera has three ax es for positioning the camera. While monitoring the picture on the monitor , adjust the camera position as follows: HorizontalAdjustment Rotate 3D assembly in the base. Do not turn assembly more than 360° as this may cause the internal cables to twist and disconnect or break.
9 2.7 Completing the Installation Once all adjustments are done, attach and secure the camera housing: 1. Use a soft, lint-free cloth to wipe the dome co ver clean and remove ngerprints.
10 OSD SETTINGS 3. OSD Settings Use the OSD menu to set up the camera for optimum performance. LENS AUTO SHUTTER/AGC AUTO WHITE BAL A TW BACKLIGHT OFF PICT ADJUST A TR OFF MOTION DET OFF NEXT EXIT SAVE ALL PRIVACY OFF DAY/NIGHT AUTO NR CAMERA ID OFF SYNC INT LANGUAGE ENGLISH CAMERA RESET BACK EXIT SAVE ALL Figure 3-1 OSD Main Menu 3.
11 OSD SETTINGS If SHUT TER/AGC is set to MANUAL, the submenu is shown as below . The shutter speed is a variable from 1/50(1/60)sec to 1/10000sec and the AGC is selectable depending on your environment condition. MODE SHUT+AGC SHUTTER 1/50(1/60) AGC 6.
12 OSD SETTINGS • PUSH: When selected in the appropriate position, the whole area will perform white balance. • PUSHLOCK: When selected in the appropriate position, WHITE BALANCE will perform once. 3.4 BACKLIGHT Set Backlight compensation function.
13 OSD SETTINGS Note: If you enable MO TION DET function, then PRIVACY function will support 4 zones only . REA SEL 1/8 TOP 000 BOT TOM 000 LEFT 000 RIGHT 000 COLOR 1 TRANSP 0.00 MOSAIC OFF 3.9 DA Y/NIGHT The camera will automatically switch to B/W mode when the illumination is under a certain threshold.
14 SPECIFICA TIONS Signal System NTSC PAL Image System Image Pickup Device 1/3 type: IT CCD Effective Pixels (HxV) 976 (H) × 494 (V) 976 (H) × 582 (V) Electric Scanning System 2:1 Interlace V : 59.94 Hz , H: 15.734KHz 2:1 Interlace V : 50 Hz , H: 15.
An important point after buying a device JVC TK-T2101RU (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC TK-T2101RU yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC TK-T2101RU - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC TK-T2101RU you will learn all the available features of the product, as well as information on its operation. The information that you get JVC TK-T2101RU will certainly help you make a decision on the purchase.
If you already are a holder of JVC TK-T2101RU, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC TK-T2101RU.
However, one of the most important roles played by the user manual is to help in solving problems with JVC TK-T2101RU. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC TK-T2101RU along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
