Instruction/ maintenance manual of the product TK-C215VP12 JVC
Go to page of 36
DOME CAMERA TK-C215VP4 TK-C215VP12 INST ALLA TION PRECA UTIONS LST0474-001B T o installation contractor : Be sure to read the followings beforehand for pr oper in stalla- tion. Pass the manu al to user after reading. To u s e r : Please be sure to keep tog ether with the instruction ma nual after reading.
Precautions rega rding fall prevention 䡵 Mounting screws f or the base Be sure to use M4 screw . 䡵 Mounting the fall pre vention wire Note: ● P a y attention to the length, strength, routing and material (insulation prope r ties) of the fall prev ention wire used.
Precautions r egarding water-proof and dust-pr oof 䡵 Fill the hole with sealing material Fill the piping hole as well as the 2 mounting holes mounted with screws using a sealing material. Memo: ● Use GE silicon or its equivalents as the sealing material.
Precautions r egarding water-proof and dust-pr oof (continued) 䡵 Precautions when mo unting the dome co ver ● Make sure that the dome cov er is fir mly fastened. Otherwise, the humidity lev el may rise, which may result in f ogging and ev en falling of the cov er .
DOME CAMERA TK-C215VP4 INSTR U CTIONS For Customer Use: Enter below the Se rial No. which is located on the body . Retain this inf ormation for future ref erence.
2 Intr oduction Safety Precautions RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION FOR USA AND CANADA Information for Users on Disposal of Old Equipment Attention: This symbol is only valid in the European Union.
3 INFORMA TION FOR USA 䡵 INFORMA TION This equipment has been test ed and found to comply with the limits for a Class B digital device , pursuant to P ar t 15 of the FCC Rules. These limits are des igned to provide reasonable protection against harmful interference in a residential installation.
4 Intr oduction 䢇 The unit is to be powered by a DC 12 V or an AC 24 V po wer supply . 䢇 The unit is to be powered by a UL Listed DC 12 V or an AC 24 V po wer supply . (F or U type) 䢇 The AC 24 V and 12 V DC power supply shall conform to the f ollowing: Class 2 only (F or USA), Isolated power supply only (F or Europe).
5 These are general IMPORT ANT SAFEGU ARDS and cer tain items may not apply to all appliances. 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to.
6 Intr oduction Thank you f or pu rchasing this product. (These instructions are for: TK-C215VP4U/TK- C215V P4E.) Before beginning to oper ate this unit, please read the instruction manual carefully in order to make sure that the best possible perf or mance is obtained.
7 Intr oduction Safety Precautions .................................... 2 Characteristics .......................................... 6 T able of Contents ................................ ...... 7 Prec auti ons for pro per use of this product .........
8 Intr oduction Storage and Location of Use 䢇 Do not install this unit at the following locations. ● Places that are exposed to v a por or oil, such as kitchens.
9 Camera A Mounting hole ⳯ 2 Use these when mounting the camera to the ceiling, wall or electrical box. ( A Pg. 17)( A Pg. 25) Note: ● T o mount the camera using the electrical bo x, consult the dealer from which this product is purchased or any nearby JVC dealer .
10 Intr oduction Camera (continued) G Base Mount the base to the ceiling, wall or electrical box bef ore mounting the camera. ( A Pg. 17)( A Pg. 25) H Fastening Screw f or Dome Cover This is a fastening scre w for the dome cov er. Use a supplied wrench to fasten/unf asten the scre w .
11 Camera (Interior) L Rotation Knob Rotate the lens unit to adjust the inclination of the image. ( A Pg. 22) M Rotation Center Mark ( A Pg. 22) N Fall Prevention Wire Use this to connect the base G to the dome cover D . O Camera Unit Fastening Screw ⳯ 2 Use this to f asten the camera unit Q to the base G .
12 Intr oduction Set the video setting switches on the camera unit before mounting it. T o set the switches, use a fine-tipped scre wdriver . A [RESET/SPO T] RESET/SPOT b utton When this button is pressed, the v alue of the white balance or phase adjusted manually is reset to the default v alue.
13 3. [SYNC] Synchronization system selection swit ch. This switch sets the synchronizing system for the camera. INT: This is set for internal synchronization LL (Line Lock): The camera’ s ver tical synchronization is lock ed to the A C 24 V 60 Hz or 50 Hz power line frequency .
14 Installation and Co nnection ● T ur n off the power of de vices to be used bef ore connecting the cables . ● Read through the “Instr uction Manual” of the devices to be used carefully bef ore connecting. Memo: ● When mounting the heater (sold separately: KA-ZH215), make sure to connect the wire to an AC 24 V po wer supply during use.
15 The maximum connection distance varies with the type of cable used. Please refer carefully to the table f or each cable during connection. * Be sure to tur n off the power of devices bef ore connecting cables. Note: ● When mounting the heater (sold separately: KA-ZH215), make sure to connect the wire to an AC 24 V po wer supply during use.
16 Installation and Co nnection Follo w the procedures below to connect/set this unit. T ur n off the power of de vices to be used before connecting the cables .
17 Remov e the dome cover , followed b y setting the video image switches. 1. Removing the dome cover Remov e the dome cover b y unf astening the 3 fastening scre ws using the wrench supplied. Memo: ● The dome cov er and base are connected with fall pre vention wire.
18 Installation and Co nnection 2. Mounting the fall p revention wire to the base (fall prevention wire is not supplied) Remov e the f astening screw f or the f all prev ention wire and mount the fall pre vention wire. Note: ● P a y attention to the length, strength, routing and material (insulation proper ties) of the fall prev ention wire used.
19 1. Connecting the coaxial cable ( A Pg. 15) Lower the protection co ver and connect the connectors. Upon connecting, cov er the connectors using the protection cover . 2. Connecting the AC 24 V/DC 12 V power supply wires Note: ● T o mount a heater (sold separately) to this unit, make sure to connect it to an AC 24 V supply during use.
20 Installation and Co nnection Fill the piping hole and mounting hole wit h a sealing material, mount the camera unit to the base, and inser t the silica gel. 1. Fill the hole with se aling material Fill the piping hole as well as the 2 mounting holes mounted with screws using a sealing material.
21 4. Inserting the silica gel suppli ed T ake out the silica gel from the aluminum package , inser t it into the silica gel inser tion space of the camera unit and fasten using the lug plate. Memo: ● During reconnectio n or re-installation after repair or maintenance, make sure to replace the silica gel with a new one.
22 Installation and Co nnection Upon mounting the camera, adjust the images while checking the actual image. Mounting the test monitor Connect the [MONITOR] terminal of this unit to the test monitor to adjust the camera’ s shooting direction, angle of view and f o cus.
23 Adjusting the angle of view , focus and brightness Upon deter mining the imaging direction, adjust the angle of view , focus and brightness accordingly . Note: ● When adjusting the focus, make sure to cov er the dome cover o ver the lens. The dome cov er of this unit is thick.
24 Installation and Co nnection After setting is complete, mount the inner dome to the camera. 1. Mounting the inn er dome Mount the inner dome to the 3 lugs. Note: ● Mount the inner dome such that it does not cov er the lens. ● When mounting the inner dome, make sure not to move the position of the lens.
25 Note: ● Make sure that the dome cov er is fir mly fastened. Otherwise, the humidity lev el may rise, which may result in f ogging and ev en falling of the cov er . ● Ensure that the fall pre vention wire of the dome cover is not caught in the space between the dome cov er and base.
26 Installation and Co nnection Use the piping hole to mount the camera. Mounting the camera usin g the piping hole at the bottom surface of the base 1. Setting the switches ( A Pg. 17) 2. Removing the camera unit from the base. ( A Pg. 17 , step 1) 3.
27 Mounting the camera usin g the piping hole at the side surface of the base If the camera cannot be mounted directly to the ceiling, mount it to the pipe using the piping hole at the side surface of the base. 1. Setting the switches ( A Pg. 17) 2. Dismantle the camera unit from the base and mount the fall prevention wire ( A Pg.
28 Installation and Co nnection As a general characteristic unique to CCDs, white-spots may appear on the screen with age. In order to reduce this phenomenon, this unit is equipped with a white-spot correction feature. Switch on the camera pow er supply and wait f o r at least 30 minutes.
29 Other s 䡵 Camera Signal system: U type : Based on NTSC standard E type : Based on P AL standard Scanning frequencies U type : 15.734 kHz (Horizontal), 59.
30 Other s 䡵 General P ower supply : AC 24 V H 50 Hz/60 Hz DC 12 V P ower consumption U type : 4.2 W : 23 W (When using KA- ZH215) E type : 340 mA : 1 A(When using KA-ZH215) Ambient temperature : - .
31 F ocus char t TK-C215VP4_JP.book Page 31 Wednesda y, September 20, 2006 5:48 PM.
© 2006 Victor Company of J apan, Limited LST0509-001A TK-C215VP4 DOME CAMERA TK-C215VP4_JP.book Page 32 Wednesda y, September 20, 2006 5:48 PM.
An important point after buying a device JVC TK-C215VP12 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC TK-C215VP12 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC TK-C215VP12 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC TK-C215VP12 you will learn all the available features of the product, as well as information on its operation. The information that you get JVC TK-C215VP12 will certainly help you make a decision on the purchase.
If you already are a holder of JVC TK-C215VP12, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC TK-C215VP12.
However, one of the most important roles played by the user manual is to help in solving problems with JVC TK-C215VP12. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC TK-C215VP12 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
