Instruction/ maintenance manual of the product MDM40001 Anaheim
Go to page of 11
#L010068 #L010068 USER'S GUIDE MODEL MDM40001 MICROSTEP DRIVER ANAHEIM AUTOMATION 910 E. Orangefair Lane Anaheim, CA 92801 TEL (714) 992-6990 FAX (714) 992-0471 E-Mail: aamotion@aol.com COPYRIGHT Copyright 19 96 by Anaheim Automation. All rights reserved.
#L010068 #L010068 1 2 TABLE OF CONTENTS INTRODUCTION PAGE INTRODUCTION ......................................... 2 ORDERING INFORMATION ................................ 3 DESCRIPTION .......................................... 4 DRIVER TERMINAL DESCRIPTION P1 .
#L010068 #L010068 3 4 4 Amp Microstep Driver MDM40001 (This Manual) 6 Amp Microstep Driver MDM60001 10 Amp Microstep Driver MDM10001 40VDC Power Supply PSA40V4A 65VDC Power Supply PSA65V5A 80VDC Power.
#L010068 #L010068 5 6 PIN DESCRIPTIONS P2 TYPICAL HOOK-UPS FOR APPLICATION : Pin# Description 1 Reduction Adjust: Phase Current Reduction Input. A resistor between this pin and pin 2 (Connector P2, Current Adjust) will proportionately reduced the current in both windings (1 second after the last positive going edge of the step clock input).
#L010068 #L010068 7 8 SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS INPUT VOLTAGE +12 TO +48 VDC OUTPUT CURRENT 4 AMPS PEAK PLATE TEMPERATURE 70° C STORAGE TEMPERATURE 40° TO +125° C INPUT CURRENT (PINS .
#L010068 #L010068 9 10 DETERMINING OUTPUT CURRENT Reducing the output current in the MDM40001 can be accomplished by connecting an The output current for the motor used when mic rostepping is determined differently from automatical ly 1 second after the last positive going edge of the step clock input.
#L010068 #L010068 11 12 STEP MOTOR CONFIGURATIONS 4 Lead Motors Step motors can be configured as 4, 6, or 8 leads. Each configuration requires different currents. Shown below are different lea d configurations and the procedures to determine their output current.
#L010068 #L010068 13 14 CONNECTING THE STEP MOTOR Phase 1&3 of the Step Motor is connected between pins 7 and 8 on connector P2. Phase 2&4 of the Step Motor is connected between pins 5 and 6 on connector P2.
#L010068 #L010068 15 16 MICROSTEP SELECTION FULLSTEP OUTPUT SIGNAL The number of microsteps per step is selected by switches 1, 2, 3, and 4 of the DI P The MDM40001 has an active LOW open drain output at Connector P1, Pin 7 labeled switch. Table 5 shows the standard resolution values along with the associated inputs ON F/S OUT.
#L010068 #L010068 17 18 TIMING FAULT PROTECTION The Direction and Microstep Resolu tion Select inputs are synchronized with the positive The MDM40001 is internally protected against over temperature and short circuits. going edge of the Step Clock inpu t.
#L010068 #L010068 19 TORQUE/SPEED CURVES TORQUE/SPEED CURVES.
An important point after buying a device Anaheim MDM40001 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Anaheim MDM40001 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Anaheim MDM40001 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Anaheim MDM40001 you will learn all the available features of the product, as well as information on its operation. The information that you get Anaheim MDM40001 will certainly help you make a decision on the purchase.
If you already are a holder of Anaheim MDM40001, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Anaheim MDM40001.
However, one of the most important roles played by the user manual is to help in solving problems with Anaheim MDM40001. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Anaheim MDM40001 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
