Instruction/ maintenance manual of the product RX-DP10VBK JVC
Go to page of 83
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
G-1 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
G-2 Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
1 T able of Contents Introduction ................................................ 2 Features ...................................................................................... 2 Precautions ........................................................
2 Intr oduction W e would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference.
3 Par ts Identification Front Panel Display W indow = L DIGIT AL AUT O ANALOG STEREO TUNED LINEAR PCM DSP DIGIT AL 3D-PHONIC PROLOGIC ONE TOUCH OPERA TION SLEEP SPEAKERS P ARAMETRIC EQ MIDNIGHT VOLUME.
4 Display W indow 1 ANALOG indicator (24) • Lights up when an analog input (source) is selected. 2 DIGIT AL A UTO indicator (24) • Lights up when auto digital input (DIGIT AL A UTO) is selected. 3 Surround/DSP mode indicators • Indicate the current Surround/DSP mode setting.
5 Remote Contr ol 5 ANALOG/DIGIT AL INPUT b utton (23) 6 SOUND button (49, 52, 64) 7 LEVEL +/ – buttons (49, 64) 8 TEST button (49, 64) 9 SURR OUND ON/OFF button (48, 64) p LINE DIRECT button (25) q.
6 AM LOOP ANTENNA AM EXT AM LOOP FM 75 COAXIAL ANTENNA AM EXT FM 75 C O A X IA L AM LOOP ANTENNA AM EXT FM 75 C O A X IA L AM LOOP Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply .
7 AM Antenna Connections Connecting the Speakers Y ou can connect the follo wing speakers: • T wo pairs of front speakers to produce normal stereo sound. • One pair of surround speakers to enjoy the surround ef fect. • One pair of surround back speak er s to enjo y 7.
8 Basic connecting procedur e 1 Cut, twist and remov e the insulation at the end of each speaker signal cable (not supplied). 2 T urn the knob counter clockwise.
9 RIGHT LEFT AUDIO PHONO CD CDR DVD DVD TA PE MD OUT (REC) IN (PLA Y) OUT (REC) FRONT CENTER L R IN (PLA Y) SUB WOOFER SURR (REAR) Connecting Audio/Video Components Y ou can connect the follo wing audio/video components to this receiv er . Refer also to the manuals supplied with your components.
10 CD player CD player To audio output CD recorder To audio input To audio output CD recorder Note: Y ou can connect either a cassette deck or an MD recorder to the T APE/MD jac ks. When connecting an MD recorder to the T APE/MD jacks , change the source name to “MD , ” which will be shown on the displa y when selected as the source.
11 S - V ID E O V ID E O V I D E O A U D IO LR AV C O M PU LINK PUSH -OPEN Video component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack.
12 VIDEO RIGHT LEFT DVD TV SOUND DBS OUT (REC) IN (PLA Y) VCR1 CENTER L R L R VCR2 MONITOR OUT S-VIDEO VIDEO Y P B /C B P R /C R 1(DVD) Y P B /C B P R /C R 2 Y P B /C B P R /C R MONITOR OUT PREOUT MON.
13 DVD player • When you connect the D VD player with stereo output jacks: Note: If your D VD play er has the component video output jacks, y ou can connect it to either the COMPONENT 1 (D VD) or the COMPONENT 2 jacks.
14 DVD DIGITAL IN DIGITAL 3 (TV) DIGITAL 4 (CDR) DIGITAL 5 (MD) DIGITAL 2 (CD) DIGITAL 1 (DVD) DBS Digital Connections This receiv er is equipped with fi ve DIGIT AL IN terminals—one digital coaxial terminal and four digital optical terminals—and one DIGIT AL OUT terminal.
15 Setting Up the RF Rod Antenna The remote control supplied for this recei ver can transmit both RF (Radio Frequency) signal as well as IR (infrared) signal.
16 3. Connect the plug of the transmitter to the IR OUT jack of the recei ver and attach the transmitter . Horizontally: 60˚ V ertically: 60˚ 15° 45° 30° 30° Signal-emitting angle of the transmitter Connecting the Power Cord Before plugging the receiv er into an A C outlet, make sure that all connections hav e been made.
17 Multi-Room Operations Before operating this receiver any further , be familiar with this Multi-room function. This function enables you to listen to different sources in two different places (we call these two places “main room” and “sub-room”) by using this receiver .
18 Basic Operating Procedur e for Main Room On the unit: 1. Press (ST ANDBY/ON). The ST ANDBY lamp goes of f, and the MAIN R OOM ON/OFF lamp lights up. The front door mov es down so that the source selecting b uttons appear , and the buttons and controls on the unit work for the main room operations.
19 MASTER V OLUME Down Up Basic Operating Procedur e for Sub-Room On the unit: 1. Press (ST ANDBY/ON). The ST ANDBY lamp goes of f, and the MAIN R OOM ON/OFF lamp lights up. The front door mov es down so that the source selecting b uttons appear , and the buttons and controls on the unit work for the main room operations.
20 Main Room Operations This section explains only the operations commonly used when you play any sound source in the main room. See pages 27 to 30 for the sub-room operations. • Before performing main room operations, it is recommended to finish the basic settings on pages 33 to 40.
21 DV D : Selects the D VD player . D VD MUL TI : Selects the D VD player for viewing the digital video disc using the analog discrete output mode (5.1CH reproduction). T o enjoy the D VD MUL TI playback, see page 53. VCR 1 : Selects the video component connected to the VCR 1 jacks.
22 The signal indicators light up to indicate the incoming signals. L :• When digital input is selected: Lights up when the left channel signal comes in. • When analog input is selected: Alw a ys lights up. R :• When digital input is selected: Lights up when the right channel signal comes in.
23 Activating the Main Room Front Speakers When shipped from the factory , both pairs of the front speakers hav e been set to be used in the main room.
24 Attenuating the Input Signal When the input le vel of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal lev el to prevent sound distortion. • Y ou have to mak e this setting for each source.
25 Changing the Display Brightness Y ou can dim the displa y . Press DIMMER. • Each time you press the b utton, the brightness lev el of the display changes as follo ws: Note: Even though the dimmer is in use , the display brightens f or a while when you oper ate the receiver (except when changing the source).
26 Notes: • Once you change the source name, it is applied both f or the main room source and sub-room source. • Without changing the source name, you can still use the connected components. Howe ver , there ma y be some inconvenience. – “T APE” or “TV” will appear on the displa y when you select the MD recorder or DBS tuner .
27 Sub-Room Operations This section explains only the operations used when you play a sound source in the sub-room. See pages 20 to 26 for the main room operations. • Before performing sub-room operations, it is recommended to finish the basic settings on pages 33 to 40.
28 T o turn off the po wer (into standby mode), press (ST ANDBY/ON) again. The ST ANDBY lamp lights up, and the front door automatically closes. (The MAIN R OOM ON/OFF and/or SUB R OOM ON/OFF lamp goes of f.) • A small amount of po wer is consumed in standby mode.
29 Selecting the Sub-Room Source to Play Press one of the sour ce selecting buttons. DV D : Selects the D VD player . VCR 1 : Selects the video component connected to the VCR 1 jacks. VCR 2 : Selects the video component connected to the VCR 2 jacks. TV/DBS : Selects the DBS tuner .
30 Activating the Sub-Room Front Speakers This section is NO T applicable to those who connect the sub- room fr ont speakers to the SUB R OOM PREOUT jacks using another amplif ier (see page 17). Bef ore you start, r emember ... • When shipped from the factory , both pairs of the front speakers hav e been set to be used in the main room.
31 Indicates the functions Y OU CAN ALSO USE when the receiv er is ready for the sub-room operations. Receiving Radio Br oadcasts Y ou can browse through all the stations or use the preset function to go immediately to a par ticular station. T uning into Stations Manually On the unit: 1.
32 Using Preset T uning Once a station is assigned to a channel number , the station can be quickly tuned in. Y ou can preset up to 30 FM and 15 AM stations. T o stor e the preset stations Bef ore you start, r emember ... • There is a time limit in doing the follo wing steps.
33 Basic Settings Some of the following settings are required after connecting and positioning your speakers, while others will make operations easier . When performing the basic settings, it is recommended to use the remote control so that you can show the on- screen display menu on the TV .
34 Operation through On-Scr een Display Menus T o do the basic settings for this receiv er, use the remote control so that you can utilize the on-screen display menus in order to finish important settings easily while viewing these menus.
35 Menu Operating Procedur e Ex. When setting the speaker distance On the TV scr een 1. Press SETUP MENU . 2. Press fi or % (DO WN or UP) repeatedly to select the desir ed submen u. • In this e xample, select “SPEAKER DIST ANCE” submenu. 3. Press SET .
36 Setting the Speaker Distance —SPEAKER DIST ANCE ( 2 ) The distance from your listening point to the speakers is another important element to obtain the best possible surround sound of the Surround and DSP modes. Y ou need to set the distance from your listening point to the speakers.
37 Setting the Bass Sounds—SUBWOOFER ( 3 ) On this submenu, you can adjust subwoofer and bass sounds precisely according to your preference. 7 Setting the crossover frequency: When you use a subwoofer , you can select the cutoff frequency for the small speakers used.
38 Setting the Dynamic Range —DYNAMIC RANGE ( 4 ) Using the Midnight mode, you can enjoy a po werful sound at night e ven at a low v olume level. 7 Setting the Midnight mode: Select one of the follo wing: 1: Select this when you want to reduce the dynamic range a little.
39 Note: When shipped from the f actor y , the DIGIT AL IN ter minals can be used as the digital input f or the following components: • DIGIT AL 1 (coaxial): For D VD pla yer • DIGIT AL 2 (optical.
40 Memorizing the V olume Level for Each Source—ONE TOUCH OPE(ration) ( w ) This unit memorizes many settings separately for each source. (See page 26.) In addition, you can store the volume le vel for each source together with the other memorized settings.
41 Sound Adjustments When performing the sound adjustments, it is recommended to use the r emote control so that you can show the on-screen display menu on the TV . • When using the buttons on the unit, you can perform the same settings referring to the indications shown on the main unit’ s display .
42 The buttons that can be used on the men us are shown on the screen. Y ou can perfor m menu oper ation with these usable b uttons. IMPORT ANT: Check to see if the f ollowing bef ore or while using the buttons and controls. For the main room operations: The MAIN ROOM ON/OFF lamp on the unit is lit.
43 Menu Operating Procedur e Ex. When adjusting a DSP parameter On the TV scr een 1. Press ADJUST MENU . 2. Press fi or % (DO WN or UP) repeatedly to select the desir ed submen u. • In this e xample, select “DSP P ARAMETER” submenu. 3. Press SET .
44 Adjusting the Speaker Channel Output Levels—LEVEL ( 1 ) On this submenu, you can adjust the speaker channel output le vels. While outputting the test tone, select a speaker channel and adjust its output le vel. Once adjustment is done on this submenu, it is stored for each source when you change the source or when you turn of f the receiv er .
45 7 Adjustment procedure on this submenu 1 Press fi or % (DO WN or UP) to select the channel— FR ONT , CENTER, SURROUND, or SURR OUND BA CK, then press SET . The adjustment screen of the selected item appears. 2 Press fi or % (DO WN or UP) to select an item you want to adjust on the selected adjustment screen.
46 Using the Sur r ound Modes This unit activates a variety of Surround Modes automatically according to the stored basic settings and adjustments performed on the Setup and Adjustment Menus (see pages 33 to 45).
47 Dolby Surround (Dolby Pro Logic) ** Used to reproduce sound tracks of the software encoded with Dolby Surround ( DOLBY SURROUND ). Dolby Surround encoding format r ecords the left front channel, right front channel, center channel, and surround channel signals (total 4 channels) into 2 channels.
48 Activating the Surr ound Modes Perform the basic settings and adjustments using the Setup and Adjustment Menus first (see pa ges 33 to 45). Activa ting the THX Surround and con ventional Surround mode for a sour ce automatically recalls the memorized settings and adjustments done on the above menus.
49 Adjusting the Surr ound Sounds T emporarily Activa ting the THX Surround and con ventional Surround mode for a sour ce automatically recalls the memorized settings and adjustments done on the Setup and Adjustment Menus.
50 Using the DSP Modes This unit provides a variety of DSP (Digital Signal Processor) Modes. • The following operations are only possible when the receiver is ready for the main room operations, and are used only for the main room sources.
51 ALL Channel Stereo mode (ALL CH STEREO) This mode can reproduce a larger stereo sound f ield using all the connected (and activ ated) speakers. This mode cannot be used without connecting the surround speak ers. • The CENTER CHANNEL submenu settings and the DSP P ARAMETER submenu settings cannot be applied to All Channel Stereo mode.
52 * When multichannel signals come in, y ou cannot select “STEREO FILM” and “MONO FILM. ” Notes: • When the surround speakers are deactivated, the 3D-PHONIC processing is applied to the DSP modes (the 3D-PHONIC indicator also lights up).
53 Using the DVD MUL TI Playback Mode This receiver provides the DVD MUL TI playback mode for reproducing the analog discrete output mode of the DVD player .
54 COMPU LINK – 4 (SYNCHRO) COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC audio components through this receiver .
55 Automatic Power On/Off (Standby): only possible with the COMPU LINK-3 and COMPU LINK--4 connection A utomatic Po wer On: • When y ou turn on the recei ver by pressing (ST ANDBY/ ON) on the unit, .
56 TEXT COMPU LINK Remote Contr ol System The TEXT COMPU LINK remote control system has been developed to deal with the disc information recorded in the CD T ext* and MDs. Using this information in the discs, you can operate the CD player or MD recorder with the TEXT COMPU LINK remote control system through the receiver .
57 OPERA TIONS: T o use this remote control system, you need to connect the main room TV to the MONITOR OUT jack (see page 12), and the sub- room TV to the SUB R OOM MONIT OR OUT jack (see page 17) and set the TV’ s input mode to the proper position to which the receiv er is connected.
58 Search for a disc by its disc title: 1. Press TEXT DISPLA Y while “CD” is selected as the source. The Disc Information screen appears on the TV . 2. Press % / fi to move to “SEARCH, ” then press SET . The DISC SEARCH screen appears. 3. Press % / fi to move to “DISC TITLE, ” then press SET .
59 Entering the Disc Information For the CD Player with the disc memory function: Y ou can use the disc memor y function through this receiver . The disc information (its performer , disc title, and music genre) of normal audio CDs will be stored into the memory built in the CD player .
60 For the MD recorder: Y ou can write the disc infor mation (disc title and song titles) into the disc. Y ou can only wr ite the song title f or the song currently selected.
61 A V COMPU LINK Remote Contr ol System This receiver is equipped with the A V COMPU LINK-III. The A V COMPU LINK remote control system allows you to operate JVC video components (TV , VCR, and DVD player) through the receiver .
62 CONNECTIONS 3: V ideo Cable Connection This receiv er is equipped with three types of the video jacks — S-video, composite video, or component video, and the signals coming into this recei ver through one type of video jacks can output only through the terminal of the same type.
63 One-T ouch DVD Play Simply by starting playback on the D VD player , you can enjoy the D VD playback without setting other switches manually . When you press PLA Y on the remote control supplied fo.
64 Operating JVC’ s Audio/V ideo Components Y ou can operate JVC’s audio and video components with this receiver’ s remote control, since control signals for JVC components are preset in the remote control. Operating Audio Components T uner Y ou can al ways perform the following operations: FM : T unes into the last selected FM station.
65 CD player After pressing CD, you can perform the following operations on the CD player: PLA Y : Starts playing. 4 : Returns to the beginning of the current (or previous) trac k. ¢ : Skips to the beginning of the next trac k. ST OP : Stops playing.
66 Operating V ideo Components IMPORT ANT : T o operate JVC’ s video components using this remote control: • Y ou need to connect JVC video components through the A V COMPU LINK jacks (see page 61) in addition to the connections using cables with RCA pin plugs (see pages 11 to 13).
67 Operating Other Manufactur ers’ Equipment Y ou can use this remote contr ol supplied for this unit for operating the other manufactur ers’ components, either by changing the preset signal codes or by using the learning function (see page 71).
68 T o change the transmittable signals for operating a CA TV conver ter and DBS tuner 1. Set the TV operation mode selector to “CA TV/DBS. ” 2. Press and hold TV/CA TV/DBS (ST ANDBY/ON). 3. Press TV/DBS. 4. Enter manufacturer’ s code using buttons 1–9, and 0.
69 After pressing D VD MENU (only for the main room operations), these buttons can be used for the D VD menu operations. Note: Ref er also to the manual supplied for y our D VD play er (and the instruction supplied for the discs). 5. T ry to operate your D VD player by pressing one of the above b uttons.
70 Manufacturer Codes JVC 00 * , 09 DENON 01, 02, 03 FISHER 04, 05 KENWOOD 10, 11, 12, 13, 14 MAGNAVOX 15, 16 MARANTZ 17 ONKYO 18, 19, 20, 21 PANASONIC 22, 23, 24 PHILIPS 25, 26, 27, 28, 29 PIONEER 30.
71 Storing the Remote Signals Manually Y ou can stor e the signals into the lear ning buttons by sending the signals you want to store from another remote control. This function is called “Learning Function. ” The learning buttons The highlighted buttons in the illustr a tion belo w are the learning buttons y ou can stor e signals into.
72 4. Press one of the learning b uttons, to which you want to assign a signal from the target r emote control. The LEARN indicator starts flashing. • If you ha ve pressed DV D or D VD MUL TI in step 3, you can store the signals into the follo wing buttons.
73 T o erase the stor ed signals After erasing the stored signals, preset signals are resumed and you can operate JVC’ s components again. 1. Set the LEARN/TRANSMIT (MAIN R OOM/SUB ROOM) selector to “LEARN. ” 2. Press and hold EXIT , then press one of the sour ce selecting buttons fr om which you want to erase the stored signals.
74 T r oubleshooting Use this char t to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC ser vice center . POSSIBLE CAUSE The power cord is not plugged in. The Multi-room function is not set correctly.
75 SOLUTION Connect an outdoor FM antenna or contact your dealer. (See page 6.) Select a new station. Check with your dealer to be sure you have the correct antenna. Check connections. (See page 6.) Move the antenna farther from automobile traffic. Connect it to the screw marked ( H ).
76 Specifications Amplifier Output Po wer At Stereo operation: Front channels: 120 W per channel, min. RMS, driv en into 8 Ω , 20 Hz to 20 kHz with no mor e than 0.02% total harmonic distortion. 120 W per channel, min. RMS, driv en into 4 Ω , 20 Hz to 20 kHz with no more than 0.
77 FM tuner (IHF) T uning Range: 87.5 MHz to 108.0 MHz Usable Sensiti vity: Monaural: 12.8 dBf (1.2 µV/75 Ω ) 50 dB Quieting Sensitivity: Monaural: 18.2 dBf (2.2 µV/75 Ω ) Stereo: 38.2 dBf (22.3 µV/75 Ω ) Signal-to-Noise Ratio (IHF-A weighted): Monaural: 78 dB at 85 dBf Stereo: 73 dB at 85 dBf T otal Harmonic Distortion: Monaural: 0.
BT -51002-5 (0301) QUALITY SER VICE HOW TO LOCA TE YOUR JVC SERVICE CENTER Dear Customer , In order to receive the most satisfaction from your purchase,please read the instruction booklet before operating the unit.In the event that repairs are necessary , please call 1 (800)537-5722 for your nearest authorized servicer or visit our website at www .
THIS LIMITED W ARRANTY IS V ALID ONL Y IN THE FIFTY (50) UNITED ST A TES, THE DISTRICT OF COLUMBIA AND IN COMMONWEAL TH OF PUERTO RICO. WHA T WE WILL DO: If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner .
VICTOR COMP ANY OF JAP AN , LIMITED EN 0701NHMMDWJEIN J V C RX-DP10VBK[J]cover_f 01.6.18, 7:02 PM 2.
An important point after buying a device JVC RX-DP10VBK (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC RX-DP10VBK yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC RX-DP10VBK - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC RX-DP10VBK you will learn all the available features of the product, as well as information on its operation. The information that you get JVC RX-DP10VBK will certainly help you make a decision on the purchase.
If you already are a holder of JVC RX-DP10VBK, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC RX-DP10VBK.
However, one of the most important roles played by the user manual is to help in solving problems with JVC RX-DP10VBK. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC RX-DP10VBK along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
