Instruction/ maintenance manual of the product LT-20DA6SK JVC
Go to page of 47
INSTRUCTIONS ENGLISH L T -20DA6SK INTEGRA TED DIGIT AL WIDE LCD P ANEL TV D igital ideo roadcasting V B DV B Trade Mark of the DVB Digital V ideo Broadcasting Project (1991 to 1996) Number: 3795.
- 1 - i For users in the UK: If you have any problems setting up your new TV, please call the Helpline on 0870330 5000 For users in the Republic of Ireland: If you have any problems setting up your new TV, please call the Helpline on 1890 - 582500 Contents Other Features .
- 2 - For your safety This equipment has been designed and manufactured to meet international safety stan- dards but, like any electrical equipment, care must be taken if you are to obtain the best re- sults and safety is to be assured. So, please read the points below for your own safety.
- 3 - table-cloths, curtains etc. Overheating will cause damage and shorten the life of the equip- ment. DONT allow electrical equipment to be exposed to dripping or splashing or objects filled with liquids, such as vases, to be placed on the equipment.
- 4 - WARNING Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down. The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up and down.
- 5 - Where to install WARNING When you install the TV on the wall, only use a JVC wall mounting unit which is designed for this TV . Make sure the TV is inst alled on the wall by a skilled installer . Locate the TV away from direct sunlight and strong lights, soft, indirect lighting is recom- mended for comfortable viewing.
- 6 - Import ant Information Please take note EXCLUSION CLAUSE JVC shall under no circumstances be liable for loss and/or damage to the product caused by: fire; earthquake; accidental dama.
- 7 - Control Panel Buttons With certain combinations of connectors and leads the back cover may not be easily fitted. If the cover is left off, this in no way infringes safety requirements.
- 8 - Using the stand This TV comes with a Table Top Stand already attached. This stand can be used to adjust the direction of the TV screen 10° backward and 5° forward . Tilt the TV up and down: While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down.
- 9 - Remote Control Buttons 3 79 $9 / I = (S tand B.
- 10 - Features It is a remote controlled Integrated Digital colour television and PC monitor . 100 programmes from VHF , UHF bands or cable channels can be preset. It can tune cable channels. Controlling the TV is very easy by its menu driven system.
- 11 - Getting Started Follow Step 1 to 7 to set up your TV : Step 1: Checking the accessories supplied Remote control unit x 1 AA/R6 battery x 2 AC adapter x 1 Power cord x 1 Step 2: Inserting batteries Remove the battery cover located on the back of the remote control by gently pulling upwards from the indicated part.
- 12 - 100 mm mount based on VESA regulation is equipped. The handle and the stand can be left by loosing the screws with a screwdriver when mount- ing the TV on a wall. Spread a soft cloth on a flat table and then place the TV on the cloth with the screen facing downwards when you leave the handle and the stand.
- 13 - IMPORTANT: Only use the adaptor supplied with this TV. The TV set is designed to operate on 24 V DC. For this, an adaptor is used which gives 24 V DC voltage. Connect this adaptor to a system that supplies 100-240 V AC, 50 Hz. Step 5: Using the cable holder A cable holder which is used to keep the connection cables tidy is supplied.
- 14 - Step 6: Switching the TV ON/OFF To switch the TV on Your TV will switch on by two steps: 1- Connect the power supply cord to the sys- tem. Then the TV switches itself to stand- by mode and the power lamp becomes red located on the front of the TV .
- 15 - First of all choose the Language which the menus of the analogue part of the TV will ap- pear. As soon as you change the language, the menu items will be displayed in the se- lected language. By pressing the or button, come to the Country item and select the country.
- 16 - When you press the following buttons ( / I , , TV / DTV, ZOOM, , , AV, MENU , SUBTITLE, GUIDE, , BACK, / , number buttons) during recording, a mes- sage appears asking if you want to stop recording or not. Press OK button to stop recording or BLUE button to continue re- cording.
- 17 - Example: PR6 press 6, PR12 press 1 and 2. Press directly the programme number to reselect single digit programmes. Hint: The channel list numbers are assigned by the broadcasters. Because not all channels are broadcast free-to-air and stored by the receiver, the channel list numbers do not run continuously.
- 18 - ELECTRONIC PROGRAMME GUIDE (EPG) Another way of selecting a channel is with the electronic programme guide, or EPG. Like the Channel List, the EPG screen dis- plays a list of the stored channels along with information on what programmes are being broadcast.
- 19 - DISPLA YING THE SUBTITLES With Digital terrestrial broadcasting (DVB-T), some programmes are broadcast with sub- titles. Subtitles can be displayed when watching these programmes. Press the SUBTITLE button when watching Digital terrestrial broadcasting (DVB-T).
- 20 - from the TV to the VCR to automatically start and end the recording. It is not necessary to set the timer on the VCR. When your VCR is not T -V LINK compatible, you also need to set the VCR timer settings to match the TV timer settings. The recording may not start and stop at ex- actly the right times for some programmes.
- 21 - Mode: Use the / buttons to choose the timer mode (Once/Daily/Weekly), and then press the O K button. 4. Prepare your VCR for recording When recording on a T -V LINK compatible VCR: 1. Insert the videotape for recording into the VCR and set the recording mode.
- 22 - Configuration Set the basic setting when watching Digital terrestrial broadcasting (DVB-T). Choose configuration and press the OK but- ton. CONFIGURATION appears. When the BACK button is pressed, the previ- ous screen is returned to. When MENU but- ton is pressed, the menu disappears .
- 23 - The actual version may be different to the Receiver Upgrade version displayed above. 2. Press the / buttons and choose Automatic Download, and press the or buttons to choose Enable and Disable.
- 24 - Sometimes you may notice a drop in picture quality while watching your programme in the quarter-screen. This is not a fault. When the BACK button is pressed, the previ- ous screen is returned to. When the TV/DTV or MENU button is pressed, the menu dis- appears.
- 25 - Setting the favourite channels If only channels that you often watch are set as favourite channels, you can choose from just those channels by pressing / . After setting the favourite channels, check the Favourite Mode in Configuration (see page 22 ) is set to ON.
- 26 - When OK button is pressed, following message will appear on the right bottom side of the screen: Manual Search: This is for searching for digital channels on a single broadcast frequency.
- 27 - T o see the viewing contract information, press MENU , Select DIGIT AL and Press OK , then Select Common Interface and press OK . When no module is inserted, No CI Mod- ule appears. Refer to the module instruction manual for details of the settings.
- 28 - Setting Sharpness Using or button select Sharpness. Press button to increase sharpness level. Press button to decrease sharpness level. Setting Colour Using or button select Colour .
- 29 - Reset Press BLUE button to reset the picture modes to factory default settings. T o Store the Settings In the Picture Menu, all settings are stored automatically.
- 30 - Selecting Sound Mode Using or button select Sound Mode. Press or button to change Sound Mode. You can choose Mono , Stereo or Dual (I-II) mode, only if the selected channel sup- ports that mode. In case of bilingual broadcast (Dual Sound), you can select original or dubbed language using mode option.
- 31 - In EXT mode, Install menu appears like this: You can change only Colour system and VCR. Selecting Programme Using or button select Programme . T o select programme number , you can use / button or Digit Buttons.
- 32 - After stored, T -V LINK menu will appear . If you do not need to do T -V LINK, select Can- cel and press or OK button to exit the menu. Program Menu Press " MENU " button, now you are in main menu. In the main menu, select Program using or button.
- 33 - automatically on your TV, according to the transmission of programme systems in your area. First of all choose the Country by using or button. Then press the Red but- ton to start Autostore. After Autostore is finalized, a programme list will appear on the screen.
- 34 - this volume is set to the preceding value, and the second one is increasing or de- creasing the volume level. No-Signal Detection (TV mode) If no valid signal detected, it takes 5 minutes to switch to the Stand-By mode unless any signal detected or any Remote Control com- mand is accessed.
- 35 - The top and bottom of the picture are slightly cut off. 14:9 ZOOM: This zooms up the wide picture (14:9 aspect ratio) to the upper and lower limits of the screen. 16:9 ZOOM: This zooms up the wide picture (16:9 aspect ratio) to the full screen.
- 36 - Auto Position If you shift the picture horizontally or vertically to an unwanted position, use this item to put the picture into correct place automatically. Select Auto position item by using or buttons. Press OK button.
- 37 - Contrast, Bright-1, Colour and Sharpness are described at Picture menu on page 27 . Setting PIP Size Using or button select PIP Size. Press or button to change PIP size. Two different PIP sizes are available.
- 38 - To select a page of Teletext Press the appropriate digit buttons for the required T eletext page number . The selected page number is displayed at the top left corner of the screen. The Teletext page counter searches until the selected page number is located, so that the desired page is displayed on the screen.
- 39 - For Fastext and T optext The subject-heading for the information may have a particular colour . Press an appropriate RED , GREEN , YELLOW or BLUE button in order to reach the relevant page quickly . For TOPTEXT If Toptext transmission is present, colour coded buttons will appear in status row.
- 40 - supply you a corresponding decoder unit to allow the programmes to be unscrambled. For further information ask your dealer. See also the booklet supplied with your decoder. Connect a decoder with an aerial socket to the TV Connect the aerial cable.
- 41 - Peripheral Equipment Connections 3& $ 8',2,1 $17( 11 $ (;7 $ % & ' ( (;7 ) * + , '& ,1 3&,1387 (;7 (;7 $8',2287.
- 42 - Peripheral Equipment Connections DECODER FOR SATELLITE RECEIVER VIDEO HEADPHONE AUDIO Antenna Connections 2XWGRR U $Q WHQQ D&RQQ HFWLRQ V ENG-20710W-17MB16P-1895UK-(LT-20DA6SK)-50076128.
- 43 - PC Input T ypical Display Modes The display has a maximum resolution of 1360x768 , vertical sync. frequency range of 50-75 Hz and a horizontal sync. frequency range of 30-69 KHz. The following table is an illustration of some of the typical video display modes.
- 44 - PC Picture If no PC picture appears, check that the D- SUB cable is connected properly. Check that your PCs resolution set correctly. See pages 43 for supported modes.
- 45 - Specifications Broadcasting Systems P AL BG , DK, I, L, Lp Channels and Digital : 474 MHz - 858 MHz Frequencies Analogue : 46.25 MHz - 862.25 MHz Cable TV (S1-S20/ S21-S41) Input Signal Video: Analog 0,7 Vp-p 75 ohm positive Sync: TTL Level positive or negative, Seperate sync.
DV B ©2005 Victor Comp any of Japan, Limited 0205MKH-VT -VT 50076128.
An important point after buying a device JVC LT-20DA6SK (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC LT-20DA6SK yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC LT-20DA6SK - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC LT-20DA6SK you will learn all the available features of the product, as well as information on its operation. The information that you get JVC LT-20DA6SK will certainly help you make a decision on the purchase.
If you already are a holder of JVC LT-20DA6SK, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC LT-20DA6SK.
However, one of the most important roles played by the user manual is to help in solving problems with JVC LT-20DA6SK. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC LT-20DA6SK along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
