Instruction/ maintenance manual of the product LST0420-001B JVC
Go to page of 32
DOME CAMERA TK-C215V4 TK-C215V12 INSTR UCTIONS (A) For Customer Use: Enter below the Se rial No. which is located on the body . Retain this inf ormation for future referen ce. Model No . TK-C215V4/TK-C215V12 Serial No. * TK-C215V4 is used in the above illustration.
2 Intr oduction Safety Precautions CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
3 I 䢇 The unit is to be powered by a DC 12 V or an AC 24 V po wer supply . 䢇 The unit is to be powered by a UL Listed DC 12 V or an AC 24 V po wer supply .
4 Intr oduction These are general IMPORT ANT SAFEGU ARDS and certain items may not apply to all appliances. 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to.
5 Intr oduction Safety P recautions ......................................... 2 Contents ......................................................... 5 Characteristics ............................................... 6 Operating Precautions ..............
6 Intr oduction Thank you f or purchasing this product. (These instructions are for: TK-C215V4U/TK-C215V12U.) Before beginning to oper ate this unit, please read the instruction manual carefully in order to make sure that the best possible perf or mance is obtained.
7 䢇 T o sav e energy , when it is not being used turn the system’ s power off. 䢇 This camera has been designed f or indoor use. It cannot be used outdoors. 䢇 Do not install or use the camera in the follo wing places. ● In a place exposed to rain or moisture .
8 Intr oduction Camera A Mounting hole (elliptica l) x 4 Use these when mounting the camera to the electrical box. ( A pg. 22) B Mounting h ole (rou nd) x 4 Use these when mounting the camera to the ceiling or wall. ( A pg. 18, 20) C Outer Case Use this in the follo wing cases: ● When mounting the camera directly to the ceiling or on the wall.
9 Camera (Interior) The dome cov er , inner dome and outer case are removed. Procedures for remo val. ( A pg. 18 A Embedding the camera to the ceiling B , Step 3. to Step 5. ) K Strap A plate to connect the camera unit and the dome cov er . L Fastening Screw (x 3) When embedding the camera in the ceiling, turn this screw to secure the camera.
10 Intr oduction Set the video setting switches on the camer a unit before mounting it. T o set the switches, use a fine-tipped scre wdr iver . A [RESET/SPO T] RESET/SPO T button When this button is pressed, the v alue of the white balance or phase adjusted manually is reset to the default v alue.
11 4. [WHT .BAL.] A TW/MANU AL selection switch. For selecting whether to adjust the white balance automatically or manually . When the setting is changed from manual to A TW , the settin g values in the manual mode will be reset. The camera s witches to the same mode as with pressing the [RESET] button.
12 Intr oduction Set the video setting switches on the camer a unit before mounting it. T o set the switches , use a fine-tipped screwdriver . A [IRIS LEVEL] Iris level adjustment For adjusting the le vel of the automatic aper ture control lens. This adjustment only needs to be made when required.
13 2. [SELECT] WHT .BAL./PHASE setting switch. WHT .B AL.: The F [R/B, +/ - ] b uttons are used as [R/B] adjustment buttons . PHASE: The F [R/B, +/ - ] b uttons are used as [+/ - ] adjustment buttons . (Default setting: WHT .BAL.) 3. [SYNC] Synchr onization system selection swit ch.
14 Installati on and connection The maximum connection distance varies with the type of cable used. Please refer carefully to the table f or each cable during conn ection. * Be sure to turn off th e power of de vices before connecting cables. Video signal cables Connect the coaxial cables (BNC) to the video signal output connector (BNC).
15 Electrical Spe cifications of Alarm In put T erminals (TK-C215V12 only) ● T o prevent penetr ation of noise in the internal circuitry , apply a non-voltage contact signal to the ALARM input terminal. N ev er apply a voltage . ● Apply an alarm signal for at least 200 ms.
16 Installati on and connection NO TE: ● T ur n OFF the power supply to all equipment to be used before making connections . ● Read the Instruct ion Manual f or each piece of equipment to be used before making connections. NO TE: ● P ower consumption of TK-C215V4/TK- C215V12 are different from one another .
17 Getting Started CA UTION: ● When mounting the camera to the ceiling, ensure to wear saf ety glasses to protect the eye from any f alling object. ● Attachment of a embedded cover in the ceiling (recess brack et) may be mandatory in cer tain regions.
18 Installati on and connection Embedding the camer a to the ceilin g * Make use of a ceiling material with a thickness between 9.5 mm to 22 mm. 䡵 Setup 1. Open a hole in the ceiling. ( R 120 mm , 4 3/4 inches) 2. Draw the fall pre vention wire mounted to the ceiling slab and the cable ou t from the ceiling in adv ance .
19 䡵 Connecting 1. Attach the fall prevention wire to th e camera, followed b y attaching it to the ceiling slab (Fall prevention wire is not included.) 2. Connect the video signal cab le . ( A pg. 14) Lower the co ver and connect the connectors . Upon connecting, cover the connectors using the protection cover .
20 Installati on and connection When mounting the camera directly to the ceiling or on th e wall When mounting to a wall, replace areas in dicated as “ceiling” in the procedures by “wall”. 䡵 Setup 1. Open a hole in the ceiling. ( R 30 mm , 1 1/8 inches) Make us e of the template sup plied to open a ho le.
21 4. Connect the video signal cab le . ( A pg. 14) Lower the protection co ver and connect the connectors. Upon connecting, restore the protection cov er to cover the connectors . 5. Connect the input po wer supply cab le . ( A pg. 16) 6. Connect the alarm cable.
22 Installati on and connection When mounting t h e camera to the electrical box NO TE: Before mounting the camer a to electrical boxes , please ref er to local building codes for bo x type to use for lo w-voltage wiring. 䡵 Connecting 1. Align j with the shootin g direction when mounting the cover to the electrical box.
23 Adjusting Im age Upon mounting the camera, adjust the images while checking the actual image. Mounting the test monitor Connect the [MONITOR] terminal of this camera to a test monitor to adjust the camera’s shooting direction, image and fo cus. * The power to the camera body must be ON when adjustments are performed.
24 Adjusting Im age Adjusting the field angle/focus/ brightness Upon deter mining the imaging direction, adjust the field angle, f ocus and iris lev el accordingly . The method of adjustment v ar ies with the camera in use. TK-C215V4 ( A pg. 24) TK-C215V12 ( A pg.
25 䡵 TK-C215V12 ● 2 types of angle of view ma y be selected for TK-C215V12. In general, set in a wa y such that the home position shoots a wide range and the alar m position a narrow range. ● Use the alarm input mode selection switch to set the actions when there is an alar m input.
26 Adjusting Im age 䡵 TK-C215V12 (continued) Registering alarm po sition For registering the angle of view during monitoring when there is an alar m input. 1. Check that the [ALARM POSITION] indicator light is turned o n. Registration of alarm position is enabled.
27 Other install ation and adjustment After setting is complete, mount the Inner dome. 1. Mount the inner dome . Mount the inner dome to th e claws (3 locations). CA UTION: ● Mount the inner dome such that it doe s not cov er the lens. ● When mounting the inner dom e, be careful not to mov e the lens position.
28 Other install ation and adjustment As a general characteristic unique to CCDs, white-spots may appear on the screen with age. In order to reduce this phenomenon, this unit is equipped with a white-spot correction feature. Switch on the camera pow er supply and wait for at least 30 minutes.
29 Other s 䡵 Camera Signal system : Based on NTSC standard Scanning frequencies : 15.734 kHz (Hor izontal), 59.94 Hz (V er tical) Image device: 1/4" IT CCD Effective picture elements: : 380,000.
30 Other s 䡵 External Dimens ions [Unit: mm (inches)] When cover is attached * Specifications and appearance of this unit and related products are subject to change for product improv ement without pr ior notice.
31 Focus chart TK-C215V4_V12_EN.boo k Page 31 Wedne sday, August 2, 2006 1:18 PM.
© 2006 Victor Company of Japan, Limited LST0420 -001B TK-C215V4/TK-C215V12 DOME CAMERA TK-C215V4_V12_EN.boo k Page 32 Wedne sday, August 2, 2006 1:18 PM.
An important point after buying a device JVC LST0420-001B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC LST0420-001B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC LST0420-001B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC LST0420-001B you will learn all the available features of the product, as well as information on its operation. The information that you get JVC LST0420-001B will certainly help you make a decision on the purchase.
If you already are a holder of JVC LST0420-001B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC LST0420-001B.
However, one of the most important roles played by the user manual is to help in solving problems with JVC LST0420-001B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC LST0420-001B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
