Instruction/ maintenance manual of the product PCS2 AMX
Go to page of 18
instruction manual Control System Accessories PCS and PCS2 P ower Current Sensors.
AMX Limited W arranty and Disc laimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Co.
T a ble of Contents i PCS and PCS2 P ower Current Sensor s T able of Contents Product Information ........ ................ ................. ................ .............. .............. ............ 1 Specifications ................................
ii PCS and PCS2 P ower Current Sensors T able of Contents.
Product Information 1 PCS and PCS2 P ower Current Sensor s Pr oduct Inf ormation The Po wer Current Sensors (PCS) and Dual Po w er Current Sensors (PCS2) provide po wer current status for AMX equipment. Exam ples of such equipment are video projectors, moni tors, audio recei vers, and VCRs.
Product Information 2 PCS and PCS2 P ower Current Sensors.
Installation 3 PCS and PCS2 P ower Current Sensor s Installation The PCS requires +12 VDC (+11 VDC to +17 VDC @ 20 mA minim um) for operation; the PCS2 is simply plu gged into a 120 V A C three-hole wall outlet t o obtain power . PCS and PCS2 Installation 1.
Installation 4 PCS and PCS2 P ower Current Sensors Preparing cap tive wires Y ou will need a wire stripper and flat-blade scre wdriv er to prepare and c onnect the capti ve wires.
Installation 5 PCS and PCS2 P ower Current Sensor s PCS2 to AXC-INP8 Connect the PCS2 output por ts to the AXC-INP8 input ports, as illust rated in FIG. 2. Follo w the illustration for Input 1 thr ough Input 8. Set the jumpers of the associated inputs on the AXC- INP8 to Switch mode.
Installation 6 PCS and PCS2 P ower Current Sensors PCS to T elevision Contr ollers FIG. 5 illustrates th e connections required for th e PCS to television controllers. PCS2 to T elevision C ontrollers FIG. 6 illustrates th e connections between the PCS2 to television controllers.
Calibration 7 PCS and PCS2 P ower Current Sensor s Calibration The PCS and PCS2 work by setting a threshold. The ST ANDBY threshold is set be-tween the current draw of the O FF state and that of the ST ANDBY st ate. The ON threshold is then set between the current draw of the ST ANDBY state and the ON state.
Calibration 8 PCS and PCS2 P ower Current Sensors If the unit has both ST ANDBY and ON states, follow these steps: 1. T urn the ST ANDBY and ON potentiom eters (PO Ts) clockwise until they stop. 2. Plug the PCS into an outlet and plug the unit (the device you are monitoring) into the PCS.
Calibration 9 PCS and PCS2 P ower Current Sensor s PCS2 Calibration When extreme accurac y is required for calibration, allow the PCS2 to warm up for a minimum of 15 minutes before calibration. The following procedures are used for both circuit 1 and circuit 2.
Calibration 10 PCS and PCS2 P ower Current Sensors.
Operation and Programming 11 PCS and PCS2 P ower Current Sensor s Operation and Pr ogramming PCS Operation When properly calibrated, the PCS senses current le ve ls from sources that have one or two le vels of power consumption.
Operation and Programming 12 PCS and PCS2 P ower Current Sensors ! A one- or two-second delay . ! V erification of status changes. During transitions between states, the PCS may ta ke 1 to 2 seconds to stabilize and its output indication may be incorrect.
Operation and Programming 13 PCS and PCS2 P ower Current Sensor s.
AMX reserves the right to alter specif ications with out noti ce at any t ime. brussels • dallas • los ang eles • mexico city • philad elphia • shanghai • singapor e • tampa • toronto* • yo rk 3000 research drive, richardson, TX 75082 USA • 469.
An important point after buying a device AMX PCS2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AMX PCS2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AMX PCS2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AMX PCS2 you will learn all the available features of the product, as well as information on its operation. The information that you get AMX PCS2 will certainly help you make a decision on the purchase.
If you already are a holder of AMX PCS2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AMX PCS2.
However, one of the most important roles played by the user manual is to help in solving problems with AMX PCS2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AMX PCS2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
