Instruction/ maintenance manual of the product HR-J682EK JVC
Go to page of 64
H R-J680EK H R-J682EK VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0474-001A PAL VCR SAT REVIEW SAT PR.
safety first 2 Safety P r ecautions The rating plate and the safety caution are on the rear of the unit. WARNI NG: DANGEROUS V OL T AGE INSI DE WARNI NG: T O PR EVENT FIR E OR SHOCK HAZA RD, DO NO T EXPOSE THI S UNIT T O RAIN OR MOISTURE.
safety first 3 The ST ANDBY/ON o button does not completely shut off mains power from the unit, but switches operating current on and off. “ y ” shows electrical power standby and “ z ” shows ON . Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder.
safety first 4 Some Do ’ s And Don ’ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Contents Diagrams of Equipment ................................ 6 Equipment K ey ............................................. 7 W elcome to JVC ............................................ 8 Three-Step Quick Start ............................... 10 Basic F eatures .
diagr ams of equipment 6 front p anel disp l a y rear p anel VCR SAT REVIEW SAT PR VCR SAT REVIEW 1 2 3 4 5 6 7 ENTREE ANT. IN ENTREE/DECODEUR IN/DECODER AV2 ENTREE/SORTIE IN/OUT SORTIE RF OUT ANTENNE.
equipment key 7 Diagr am K ey 5 AV1 (L-1) IN/OUT Connector enables A V connection to TV or second VCR; input r ecordable when L-1 selected. 6 AUDIO OUT (L/R) Connectors enable connection of audio cassette recorder , TV or second V CR for dubbing. 7 RF .
wel come t o jv c 8 before y ou s t art Please read the SAFETY FIR ST on pages 2–4 it tells you about some safety points Refer to the diagrams on pages 6–7 when reading through these instructions .
wel come t o jv c 9 GETTING EVERYTHING READY (continued) connect cables Connect the cables as indicated in the diagram ( below ), using the TV Aerial Cable , the RF Cable and the 21-pin SC AR T Cable ( not provided ). sc art and rf SCART is a recommended option because its use impro ves the quality of the picture.
three-step q uick st art 10 before y ou s t art Check that the V CR is turned off and no cassette is inserted Load the batteries into the Remote Contr ol Refer to the Remote Control diagram on pages 6.
three step quick st art 11 before y ou s tar t Check that the V CR is turned off and no cassette is inserted Load the batteries into the Remote Contr ol Refer to the Remote Control diagram on pages 6.
three-step q uick st art 12 Check the R esults When Auto Setup or Preset Do wnload finishes, you will see one of the three following examples on the VCR display panel: The Preset P ositions and the Clock have been set successfully Go straight to Step 3 (20:00 used as example only).
Basic F eatur es Playback ..................................................... 14 Playback F eatures ...................................... 16 R ecording ................................................... 18 VIDEO Plus+ ® Timer Programming ........
basic fea t ures 14 before y ou s t art T urn the TV on T une the TV to your Video Channel or to its A V mode ntsc t apes If an NTSC tape is played, ‘NTSC a PA L ’ appears on screen for about 5 seconds Some TVs will shrink the picture and place black bars at the top and bottom of the screen.
basic fea t ures 15 R ewind and F ast Forwar d re wind Press the < button on the Remote Control. f a st forward Press the > button on the Remote Control. SQPB This VCR is equipped with SQPB (S-VHS QUASI PLAYBACK) that lets you watch tapes recorded in the S-VHS format and the SP mode, with regular VHS resolution.
basic fea t ures 16 Playback F eatures Pause During Playback Press the | button on the VCR or the Remote Control. • If the paused picture on the TV screen jumps vertically, press the PR button on the Remote Control until the picture is steady. • Press .
basic fea t ures 17 T V P R + T V P R – T V – T V + TV 0000 STOP FIN MENU OK TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 12 3 4 6 5 7 8 9 0 DATE START DEBUT PR 2 4 1 3 E N T E R / E N T R E E EXPRESS Slow Motion This VCR will play your cassette forwards or backwards in slow motion.
basic fea t ures 18 before y ou s t art T urn the TV on T une the TV to your Video Channel or to its A V mode Choose a blank cassette which has the record safety tab still in place R ecord Safety T ab L oad the cassette into the V CR (see page 14) T V P R + T V P R – T V – T V + TV 0000 STOP FIN MENU OK TV/VCR DAILY/QTDN.
basic fea t ures 19 T V P R + T V P R – T V – T V + TV 0000 STOP FIN MENU OK TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 12 3 4 6 5 7 8 9 0 DATE START DEBUT PR .
basic fea t ures 20 R ecording R esume F unction If there is a power cut during recording (or Instant Timer Recording or timer recording), the recording will resume automatically when power is restored to the VCR unless the VCR’s memory backup has expired.
basic fea t ures 21 before y ou s tar t Make sure that the VC R’ s clock is set correctly Insert a cassette with the safety tab in place T urn on the TV and select the V ideo channel or the A V Mode T V P R + T V P R – T V – T V + TV 0000 STOP FIN MENU OK TV/VCR DAILY/QTDN.
basic fea t ures 22 T V P R + T V P R – T V – T V + TV 0000 STOP FIN MENU OK TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 12 3 4 6 5 7 8 9 0 DATE START DEBUT PR 2 4 1 3 E N T E R / E N T R E E EXPRESS Check the R esults Press O .
basic fea t ures 23 R eturn to Normal Screen Press p or O . PROGRAM COMPLETED appears on the TV screen for about 5seconds, then the normal TV screen appears. If the timer programme is overlapped with another one that was already set, PROGRAM OVERLAPPE D appears on the TV screen.
basic fea t ures 24 before y ou s t art Make sure that the VC R’ s clock is set correctly Insert a cassette with the safety tab in place T urn on the TV and select the V ideo channel or the A V Mode.
basic fea t ures 25 T V P R + T V P R – T V – T V + TV 0000 STOP FIN MENU OK TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 12 3 4 6 5 7 8 9 0 DATE START DEBUT PR .
basic fea t ures 26 Screen A Screen B Check, Cancel & Change Pr ogrammes Press c , then press o to disengage the timer mode. revie w the progr ammes Press C . The TV screen will display a list of the programmes set for timer recording (screen A). Pressing C again will cycle through each of the entries in the VCR’s memory (screen B).
basic fea t ures 27 When Pr ogr ammes Overlap Each Other If PROGRAM OVERLAPPE D appears, you have another programme overlapping the programme you have just made. confirm ov erl apping programmes The Program Check screen appears and conflicting programmes will start blinking.
basic fea t ures 28.
Adv anced F eatur es Picture Quality ........................................... 30 The B.E.S.T . Picture System ...................... 31 Sound Modes ............................................ 32 Finding S pecific Scenes ...........................
ad v anced fea tures 30 Pictur e Quality Manual T r acking Your VCR is equipped with automatic tracking control. This will be adequate for most tapes and will automatically adjust the tracking to suit.
ad v anced fea tures 31 about b.e.s.t. Works in SP and LP modes Does not work with Auto Satellite Prog Recording Works befor e T imer Recording B.E.S.T . data is lost when tape is ejected Pressing the T button on VC R does not start Instant Timer Recording while B.
ad v anced fea tures 32 before y ou s t art Set On Screen Display (O.S.D.) to ON ( Z pg. 44) Sound Modes NIC AM Stereo and Bilingual Br oadcasts This VCR is equipped with a digital stereo sound decoder ( NICAM ) which makes the reception of stereo and bilingual broadcasts possible.
ad v anced fea tures 33 Finding S pecific Scenes Skip Sear ch During playback, press 3 up to 4 times. Each press of the 3 button will cause the VCR to go into fast-motion playback for a period of 30 seconds. Normal playback resumes automatically. • To return to normal playback during a Skip Search, press .
ad v anced fea tures 34 T -V Link F unctions When you connect the V CR and your TV via both the RF cable and the fully- wired 21-pin SCART cable ( Z pg. 9), the following functions ar e available. Y ou can use these functions only with a TV offering T -V Link, etc.
ad v anced fea tures 35 Direct R ec You can start recording the programme that you are watching on your TV with simple operation. Press and hold T and press . on the Remote Control, or press T on the VCR. Follow the procedure below to use this function.
ad v anced fea tures 36 Satellite R eceiv er Contr ol Settings The following pr ocedure is requir ed if you receiv e satellite channels through a satellite receiv er .
ad v anced fea tures 37 Setting satellite receiv er’ s brand After installation, set the satellite receiver’s brand correctly and perform test; otherwise, the Satellite Controller cannot work correctly. turn on sa tellite receiv er Turn on the satellite receiver’s power.
ad v anced fea tures 38 Check R esult of T est If the satellite receiver’ s channel number has been changed to the same channel as you set ... Press the A and B buttons to move the highlight bar to CHANGED T O ... , then press O (or E ) to finish the Sat Control Set mode.
ad v anced fea tures 39 Auto Satellite P r ogr amme R ecording Auto R ecord fr om Satellite R eceiver This facility allows a programme timer-recorded using the satellite receiver to be recorded on the VCR. connect up Connect your satellite receiver, TV and VCR ( see diagram below ).
ad v anced fea tures 40 programme sa tellite receiv er Enter the details of the programme into your satellite receiver ( see receiver manual ) and put a tape in the VCR. get to the mode set screen Press m . Move the highlight bar to MODE SET using the A and B buttons and press O (or E ).
ad v anced fea tures 41 Editing L-2 SE LECT Setting Set L-2 SELECT to the appropriate mode depending on the type of unit connected to the rear panel AV2 (L-2) IN/DEC ODE R connector of this VCR. get to the mode set screen Press m . Move the highlight bar to MODE SE T using the A and B buttons and press O (or E ).
ad v anced fea tures 42 TV Set Video Channel or A V Mode Another VCR Y our VCR 21-pin SCART Cables (not pro vided) Y our V CR as the Player Y our V CR as the Recor der RF Cable (provided) Y our VCR An.
ad v anced fea tures 43 Editing from a Camcor der connect up Connect the Camcorder’s AUDIO/VIDEO OUT connecter to the VCR’s rear panel AV1 (L-1) IN/OUT or the A V2 (L-2) IN/DECODER connecter, via an optional cable adapter.
ad v anced fea t ures 44 Other F unctions On-Screen Display (O.S.D.) This function allows you to turn the on-screen information ON or OFF . get to the mode set screen Press m , move the highlight bar to MODE SET using the A and B buttons and press O (or E ).
ad v anced fea t ures 45 Po w er Save Mode You can reduce the power consumption while the VCR is turned off. get to the mode set screen Press m . Move the highlight bar to MODE SET using the A and B buttons and press O (or E ). select po wer sa ve mode Move the highlight bar to POWER SA VE using the A and B buttons.
ad v anced fea t ures 46 Auto Timer When the AUT O TIMER is set to ON , the timer is automatically engaged when the VCR power is turned off and automatically disengaged when the VCR is powered back on. get to the mode set screen Press m . Move the highlight bar to MODE SET using the A and B buttons and press O (or E ).
ad v anced fea t ures 47 ENTREE ANT. IN ENTREE/DECODEUR IN/DECODER AV2 ENTREE/SORTIE IN/OUT SORTIE RF OUT ANTENNE AV1 SORTIE OUT R L AUDIO CONTROLEUR SAT SAT CONTROL ( L-1 ) ( L-2 ) I I I I I I I I I .
ad v anced fea t ures 48 before y ou st art The power cord must be plugged in and connected to the VCR The V CR must be turned off and no cassette inserted The R emote Control must hav e batteries ins.
ad v anced fea tures 49 T uner S et The V CR needs to find, identify and memorise all av ailable stations in your area in order to record pr ogrammes correctly . Once done, pressing the A or B buttons enables you to jump to the available channels without going via any v acant channels.
ad v anced fea tures 50 Manual Channel Setup get to the confirma tion screen Press m . Move the highlight bar to MANUAL CH SET using the A and B buttons and press O (or E ). select position Use the M button on the Remote Control to move the highlight bar to a vacant position then press O .
ad v anced fea tures 51 PR 01 02 03 04 05 06 07 CH 26 33 23 30 37 [ 10 ] a k : EDIT a [ x ]: DELETE [MENU]: EXIT ID BBC1 BBC2 ITV CH4 CH5 - - - - - - - - PR 08 09 10 11 12 13 14 CH ID - - - - - - - - - - - - - - - - - - - - - - - - - - - - Change S tation Name get to the confirma tion screen Press m .
ad v anced fea tures 52 Change Station P reset P osition get to the confirma tion screen Press m . Move the highlight bar to MANUAL CH SET using the A and B buttons and press O (or E ). select item Use the M button on the Remote Control until the item you want to move begins blinking then press O .
ad v anced fea tures 53 ST ATION NAME ID Grampian TV GRM P Hessen1 HR1 Hessen3 HR3 HR T HR T HTV HTV ITV Network ITV Kabelkanal KABL London LNDN MD R MD R MTV MT V Nord3 N3 NDR1 ND R1 NDR3 ND R3 NED1 .
ad v anced fea tures 54 Region T ransmitter BBC1 BBC2 ITV CH4 CH5 London & South-East Bluebell Hill 40 46 43 65 — Crystal Palace 26 33 23 30 37 D o v e r 5 05 66 65 3— Heathfield 49 52 64 67 .
ad v anced fea tures 55 Clock S et You should only need to perform this function if: • Auto Clock Set was not performed correctly by Auto Setup, Preset Download or Auto Channel Set • The VCR’s memory backup has expired • You want to change the Just Clock setting Setting the Clock get to the initial set screen Press m .
ad v anced fea tures 56 Guide P r ogr am Numbers Guide Progr am Numbers are used by the VIDEO Plus+ system to identify the correct preset to record. Y ou should only need to perform this function if: .
subsidiar y inf ormation 57 Question and Answ ers PLA YBACK Q: What happens if the end of the tape is reached during playback or search? A: The tape is automatically rewound to the beginning. Q: Can the VCR indefinitely remain in the still mode? A: No.
subsidiar y inf ormation 58 T roubleshooting SYMPT OM POSSIBL E C AUSE CORRECTIVE ACTION POWER 1. No power is applied to the V CR. 2. The clock is functioning properly , but the VCR cannot be pow ered. 3. The Remote Control won’t function. T APE TRANSPORT 1.
subsidiar y inf ormation 59 SYMPT OM POSSIBL E C AUSE CORRECTIVE ACTION RECORDING 1. Recor ding cannot be star ted. 2. TV broadcasts cannot be recor ded. 3. T ape-to-tape editing is not possible. 4. Camcorder recording is not possible. TIMER RECORDING 1.
subsidiar y inf ormation 60 SYMPT OM POSSIBL E C AUSE CORRECTIVE ACTION OTHER PROBLEMS 1. Whistling or howling is heard from the TV during camcorder recording. 2. When scanning channels, some of them are skipped o ver . 3. The preset cannot be changed.
list of terms 61 List of T erms N N N N N Next Function Memory .......................................... 46 NICAM Stereo and Bilingual Broadcasts ................ 32 NTSC Tapes .............................................................. 14 O O O O O On-Screen Display (O.
MEMO.
MEMO.
HR-J680/682EK COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD. EK Printed in Germany 0101 IYV * ID * JVE VICTOR COMP ANY OF JAPAN, LIMITED s p e c i f i c a t i o n s g e n e r a l Power r equirement : AC 220 V – 240 V Ó , 50 Hz/60 Hz Power consumption : on : 16 W , off : 4.
An important point after buying a device JVC HR-J682EK (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC HR-J682EK yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC HR-J682EK - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC HR-J682EK you will learn all the available features of the product, as well as information on its operation. The information that you get JVC HR-J682EK will certainly help you make a decision on the purchase.
If you already are a holder of JVC HR-J682EK, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC HR-J682EK.
However, one of the most important roles played by the user manual is to help in solving problems with JVC HR-J682EK. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC HR-J682EK along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
