Instruction/ maintenance manual of the product HR-J655EK JVC
Go to page of 48
H R-J655EK VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0052-001B PAL T V P R O G + T V P R O G – T V – T V + TV 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN.
2 SAFETY FIRST IMPORT ANT n Please read the various precautions on p. 2 – 3 of this instruction manual before installing or operating the recorder . n It should be noted that it may be unlawful to r.
3 This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment.
4 QUICK SET UP GUIDE T V P R O G + T V P R O G – T V – T V + TV 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 123 4.
5 AV1 IN/OUT AV2 IN R L AUDIO ANT. IN RF OUT OUT A V CONNECTION T o Connect T o A TV with 21-pin A V input connector (SCAR T) . . . 1– Connect the aerial, recorder and TV as per “RF CONNECTION”.
6 123 456 7 89 0 2 4 1 3 ? QUICK SET UP GUIDE (cont.) STEP 3 AUTO SET UP SET THE TUNER CHANNELS, CLOCK, GUIDE PROGRAM NUMBERS AND VIDEO CHANNEL* The Auto Set Up function sets the tuner channels, clock.
7 IMPORT ANT n In certain reception conditions, station names may not be stored correctly , and auto Guide Program Number Set may not work properly . If the Guide Program numbers are not set properly , when you timer-record a TV programme using V ideo Plus+, the recorder will record a TV programme of a different station.
8 BASIC OPERA TIONS Playback The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
9 123 456 7 89 0 2 4 1 3 ? Still Picture/Frame-By-Frame Playback P AUSE DURING PLA YBACK 1 Press P AUSE . If there is vertical jitter , use the TV PROG buttons to correct the picture. ACTIV A TE FRAME-BY -FRAME PLA YBACK 2 Press P AUSE . Each time P AUSE is pressed the tape will advance one frame.
10 TV signals being received by the recorder ’ s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder . BASIC OPERA TIONS (cont.) Recording T urn on the TV and select the VIDEO channel (or AV mode).
11 Record One Pr ogramme While W atching Another 123 456 7 89 0 2 4 1 3 ? Elapsed Recording Time Indication Y ou can check the exact time of a recording. T ape Remaining Time DISPLA Y REMAINING TIME 1 Press DISPLA Y (or – –:– – ) until the time remaining on the tape appears.
12 ACCESS VIDEO PLUS+ SCREEN 1 Press PROG . The front display panel looks like this: ENTER PLUSCODE NUMBER 2 Press the NUMBER keys to enter the PlusCode number of the programme you wish to record. ● If you make a mistake, press and input the correct number .
13 SET T APE SPEED 4 Press SP/LP ( ) to set the tape speed. SET PDC MODE 5 Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON.
14 123 456 7 89 0 2 4 1 3 ? OK WEEKLY 7 9 DAILY 6 Express Timer Pr ogramming BASIC OPERA TIONS (cont.) If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer -record the programme.
15 ENTER PRESET POSITION 6 Press TV PROG +/– to enter the preset position corresponding to the broadcasting station you wish to record. SET T APE SPEED 7 Press SP/LP ( ) to set the tape speed. SET PDC MODE 8 Press PDC to select "ON" or "OFF".
16 BASIC OPERA TIONS (cont.) Check, Cancel And Replace Programmes DISENGAGE TIMER MODE 1 Press ‰ , then press . ACCESS PROGRAMME CHECK SCREEN/DISPLA Y 2 Press . ACCESS PROGRAMME SCREEN/ DISPLA Y 3 Press again to check more information. Each time you press , the next programme's information appears.
17 Index Search Y our recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode.
18 ADV ANCED OPERA TIONS (cont.) Playback/ Recording According T o T ape Charac- teristics The B.E.S.T . (Biconditional Equalised Signal T racking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures.
19 Recording ST AR T RECORDING 1 Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder . DURING B.E.S.T . B.E.S.T . COMPLETE ● The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.
20 123 456 7 89 0 2 4 1 3 ? TV PROG Manual T racking Y our video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some cir cumstances it may be necessary to make manual tracking adjustments.
21 Soundtrack Selection Y our video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.
22 This facility allows you to record automatically a satellite programme which is timer -programmed on your external satellite receiver . Connect a satellite receiver to the recorder's A V2 IN c.
23 A TTENTION ● Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.
24 123 456 7 89 0 2 4 1 3 ? ADV ANCED OPERA TIONS (cont.) Edit T o Or Fr om Another V ideo Recorder Y ou can use your video recorder as the source player or as the recording deck. MAKE CONNECTIONS 1 Connect the player’s 21-pin SCAR T connector to the recorder’s 21-pin SCAR T connector as illustrated on the below .
25 123 456 7 89 0 2 4 1 3 ? Y ou can use a camcorder as the sour ce player and your video recorder as the recorder . Edit Fr om A Camcorder MAKE CONNECTIONS 1 Connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's rear panel A V2 IN or AV1 IN/OUT connector via the optional cable adapter .
26 T urn on the TV and select the VIDEO channel (or A V mode). ADV ANCED OPERA TIONS (cont.) On-Screen Display NOTES: ● When you use this recorder as the player for editing, be sure to set "O.
27 Auto Timer When the Auto T imer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on. ACCESS MAIN MENU SCREEN 1 Press MENU . ACCESS MODE SET SCREEN 2 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or .
28 Repeat Playback Y our video recorder can automatically play back the whole tape 50 times repeatedly . ST AR T PLA YBACK 1 Press PLAY . ACTIV A TE REPEA T PLA YBACK 2 Press PLA Y and hold for over 5 seconds, then release. ● The Play indicator ( ) on the display panel blinks slowly .
29 AV1 IN/OUT AV2 IN R L AUDIO ANT. IN RF OUT OUT I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I Connection T o A Stereo System These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.
30 SUBSIDIAR Y SETTINGS V ideo Channel Set V ideo Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. With A V Connection ACCESS VIDEO CHANNEL SET MODE 1 Press and hold down STOP on the recorder until the display panel shows the following.
31 Before performing the following procedure, make sure that: n the mains power cord is plugged into the mains outlet. n the video recorder is turned off and there is no cassette inserted in the recorder . n the connected TV is turned on. n batteries have been installed in the remote control.
32 123 456 7 89 0 2 4 1 3 ? SUBSIDIAR Y SETTINGS (cont.) T uner Set IMPORT ANT Perform the following steps only if — — Auto Channel Set has not been set correctly by Auto Set Up function ( Z pg. 6). — you have moved to a different area or if a new station starts broadcasting in your area.
33 VIEW CONFIRMA TION SCREEN 4 After "SCAN COMPLETED" is displayed on the screen for about 5 seconds, a Confirmation screen looking like the one on the right appears. The stations your recorder located appear on a Confirmation screen — preset positions (PR), channels (CH) and station names (ID – Z pg.
34 SUBSIDIAR Y SETTINGS (cont.) Storing Channels Manually T o s tore channels that were not stored during Auto Set Up ( Z pg. 6) or Auto Channel Set ( Z pg. 32). ACCESS MAIN MENU 1 Press MENU . ACCESS CONFIRMA TION SCREEN 2 Press %fi to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or .
35 Perform steps 1 and 2 of "Storing Channels Manually" on page 3 4 to access the Confirmation screen before continuing. Change Station Preset Position SELECT ITEM 1 Press % fi until the item you want to move begins blinking. Then press OK and the station name (ID) and its channel (CH) number begin blinking.
36 SUBSIDIAR Y SETTINGS (cont.) % SELECT ST A TION NAME CHARACTER 1 Press until the first letter of the station name begins blinking. ENTER NEW CHARACTER 2 Press %fi to cycle through the characters (A–Z, 0–9, –, * , +, (space) ) and stop when the desired character is indicated, then press to enter .
37 TV Station And ID List ST ATION NAME ID* Anglia TV ANGL ARD ARD ARTE AR TE BBC Group BBC BBC1 BBC1 BBC2 BBC2 Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 BR1 Bayern3 BR3 BR T1 BRT1 BR T2 BRT2.
38 SUBSIDIAR Y SETTINGS (cont.) TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV . BBC1 BBC2 ITV CH4 CH5 London & South-East Bluebell Hill .
39 Just Clock The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set "ON" or "OFF" at the Clock Set screen (the default setting is "ON").
40 V ideo Plus+ Setup SUBSIDIAR Y SETTINGS (cont.) IMPORT ANT Normally , Auto Set Up ( Z pg. 6) or Auto Channel Set ( Z pg. 32 ) sets the Guide Program Numbers automatically . Y ou need to set the Guide Program Numbers manually only in the following cases.
41 PLA YBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
42 SUBSIDIARY INFORMA TION (cont.) Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair .
43 CORRECTIVE ACTION Re-perform the clock and/or timer settings. Press ‰ and confirm that “ ‰ “ is displayed on the display panel. T imer programming can’ t be performed while a timer recording is in progress. W ait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape.
44 FRONT VIEW SUBSIDIARY INFORMA TION (cont.) DISPLAY REC LINK COUNTER RESET TV PROG TV PROG TIMER STANDBY/ON SP/LP PUSH JOG 1 2 3 # & ^ % $ ! 8 0 9 4 5 6 7 * @ 1 ST ANDBY/ON Button turns recorder on/off (loading a cassette also turns power on). 2 TIMER Button engages timer standby mode.
45 AV1 IN/OUT AV2 IN R L AUDIO ANT. IN RF OUT OUT 1 6 5 4 3 2 4 ANT . IN Connector enables connection of aerial. Z pg. 5 5 A V2 IN Connector enables connection of satellite receiver or second recorder; input recordable when "L-2" selected. Z pg.
46 SUBSIDIARY INFORMA TION (cont.) REMOTE CONTROL Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button. Z "Operating JVC TVs" on page 47. 1 TV Button enables remote control of your JVC TV .
47 ) WEEKLY Button enables timer recording of weekly serials. Z pg. 13, 15 q AUX Button selects recorder's auxiliary input mode. Z pg. 24 w ‰ Button engages timer -standby mode. Z pg. 13, 15 e DA TE +/– Button inputs date of programme for timer recording.
HR-J655EK COPYRIGHT © 1998 VICTOR COMPANY OF JAPAN, LTD. EK Printed in Japan 0498HOV * UN * VP V ICTOR COM P ANY OF JAPAN, LIMITED GENERAL Power requirement : AC 220 – 240 V ` , 50/60 Hz Power consumption Power on : 24 W Power off : 5.
An important point after buying a device JVC HR-J655EK (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC HR-J655EK yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC HR-J655EK - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC HR-J655EK you will learn all the available features of the product, as well as information on its operation. The information that you get JVC HR-J655EK will certainly help you make a decision on the purchase.
If you already are a holder of JVC HR-J655EK, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC HR-J655EK.
However, one of the most important roles played by the user manual is to help in solving problems with JVC HR-J655EK. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC HR-J655EK along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
