Instruction/ maintenance manual of the product GR-SX867UM JVC
Go to page of 52
LYT0502-001A EN C O M P A C T V H S C A M C O R D E R INSTRUCTIONS G R - S X 8 6 7 U M ENGLISH CONTENTS SAFETY PRECAUTIONS 2 – 5 QUICK OPERA TION GUIDE 6 MAJOR FEA TURES 7 PROVIDED ACCESSORIES 7 GETTING ST ARTED 8 – 15 RECORDING 16 – 30 Basic Recording .
2 EN Using This Instruction Manual • All major sections and subsections are listed in the T able Of Contents on the cover . • Notes appear after most subsections. Be sure to read these as well. • Basic and advanced features/operation are separated for easier reference.
EN 3 When the equipment is installed in a cabinet or on a shelf, make sure that is has sufficient space on all sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear). Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper , or cloth etc.
4 EN ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250.
EN 5 USE 1. Accessories T o avoid personal injury: • Do not place this product on an unstable cart, stand, tripod, bracket or table. It may fall, causing serious injury to a child or adult, and serious damage to the product. • Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.
6 EN A B 3 1 2 3 2 1 Using the battery pack Hook its end to the camcorder and push the battery pack in until it locks in place . (Charging procedure, Z pg. 8) T o remove the battery pack Slide BA TTERY RELEASE and pull out the battery pack. QUICK OPERA TION GUIDE 1 Set the Power Switch to “PLA Y”.
EN 7 MAJOR FEA TURES Cassettes marked and can be used with this camcorder . NOTES about Automatic Demonstration Automatic Demonstration takes place when “DEMO MODE” is set to “ON” (factory-preset). n A vailable when the Power Switch is set to “AUT O” or “PRO.
8 EN GETTING ST ARTED Power This camcorder’s 3-way power supply system lets you choose the most appropriate source of power . Do not use provided power supply units with other equipment. CHARGING THE BA TTERY P ACK 1 Make sure you unplug the camcorder ’ s DC cord from the AC Power Adapter/Charger .
EN 9 A B A TTENTION: Before detaching the power source, make sure that the camcorder ’ s power is turned off. Failure to do so can result in a camcorder malfunction. USING THE BA TTERY P ACK Hook its end to the camcorder and push the battery pack in until it locks in place .
10 EN Clock (Lithium) Battery Insertion/Removal This battery is necessary for clock operation and to perform date/time settings. 1 Switch off the unit’ s power and remove the power supply unit (battery pack, AC Power Adapter/Battery Charger , etc.).
EN 11 4 R I T D J D 4 B E N I A L E R A C T T T I M E C . L E P O T K T E / U I T T I M R M I L I D O N E M A M D E N E N E G O . . O O E 0 O F F N 6 F F F G F LIS H Y M D T E E O A I X A N Y M I R T E T H DA T E / T I M P E M 2 8 0 J : 0 U 2 2 0 N 8 0 4 R I T D J D 4 B E N I A L E R A C T T T I M E C .
12 EN Recording Mode Setting Set depending on your preference. 1 Set the Power Switch to “AUT O” or “PRO.”. Press SP/ EP for more than 1 second. “SP” (Standard Play) provides higher picture and sound quality and is better for dubbing, while “EP” (Extended Play) is more economical, providing three times the recording time.
EN 13 4 D T S T 4 N . E – A R E Z L V P E X O E H E T T O S U M M L R A E E N C T N R G O TH O O O T N F F 3 F F 0 O O E N F X F IT S – VHS E T T T 4 E A R L P E E E TU M L R A E N C N R G O TH O T F 3 F 0 Normal Screen Select Wheel MENU Button Power Switch Menu Screen Setting Menu Display: when a VHS cassette is loaded.
14 EN Recording Playback NOTES about S-VHS and S-VHS ET n JVC EHG (Extra High Grade) tapes are recommended for superior results. Use S-VHS tape for storing recordings for an extended period or for recording important scenes, as it enables higher-quality recording and playback.
EN 15 1 3 3 2 2 180 ° 180 ° 2 3 1 4 PAUSE Power Zoom Lever Recording Start/Stop Button Set to “CAMERA” (“AUTO” or “PRO.”). Grip Adjustment 1 Separate the V elcro strip.
16 EN 25 MI N 120MIN 3MIN 2MIN MIN 119MIN 1MIN 0MIN NOTE: Y ou should already have performed the procedures listed below . If not, do so before continuing. ● Power ( Z pg. 8) ● Recording Mode Setting ( Z pg. 12) ● Load A Cassette ( Z pg. 10) ● Grip Adjustment ( Z pg.
EN 17 NOTES: ● The cassette holder cannot be opened unless a power supply is attached. ● There may be a delay after you slide EJECT until the cassette holder opens. Do not use force. ● The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary according to the type of tape used.
18 EN 1X Zoom in (T : T elephoto) Zoom out (W: Wide angle) Power Zoom Lever Zoom indicator bar FEA TURE: Zooming PURPOSE: T o produce the zoom in/out effect, or an instantaneous change in image magnification. Digital circuitry extends the maximum magnification offered by optical zoom.
EN 19 5S PAUSE FEA TURE: Quick Review PURPOSE: T o check the end of the last recording. OPERA TION: 1) Set the Power Switch to “CAMERA” (“AUT O” or “PRO.”). 2) Press 2 and release quickly during the Record– Standby mode. n T ape is rewound for approx.
20 EN DANGER n The video light can become extremely hot. Do not touch it either while in operation or soon after turning it off, otherwise serious injury may result. n Do not place the camcorder into the carrying case immediately after using the video light, since it remains extremely hot for some time.
EN 21 Fade/Wipe Effects These effects let you make pro-style scene transitions. Fade- or wipe-in works at recording start, and fade- or wipe-out works at recording end or when you enter Record–Standby mode. 1 Set the Power Switch to “PRO.”. 2 Press EFFECT repeatedly until the desired mode’ s name and indication appear .
22 EN Program AE With Special Effects 1 Set the Power Switch to “PRO.”. 2 Press P .AE repeatedly until the desired mode’ s name and indication appear . They are displayed for approx. 2 seconds, then the name disappears so that only the indication remains.
EN 23 Using Menus For Detailed Adjustment This camcorder is equipped with an easy-to-use, on-screen menu system that simplifies many of the more detailed camcorder settings. 1 Set the Power Switch to “PRO.”. 2 Menu access depends on the function you select.
24 EN RECORDING Advanced Features (cont.) Menu Screen A vailable Using The Select Wheel : Factory-preset Menu Screen A vailable Using The MENU Button This Menu Screen cannot be accessed while recording. MENU SCREEN EXPLANA TIONS Refer to “Focusing” ( Z pg.
EN 25 Menu Screen A vailable Using The MENU Button (cont.) : Factory-preset ON Records in S-VHS on a VHS or S-VHS cassette ( Z pg. 13). OFF Records in VHS on a VHS or S-VHS cassette ( Z pg. 13). Allows you to set the tape length depending on the tape used ( Z pg.
26 EN RECORDING Advanced Features (cont.) D E C 25. 99 DEC 25. 99 AM 10 : 25 : 00 AM 10 : 25 : 00 DEC 25. 99 (DATE) (TIME) (DATE&TIME) AUTO DATE No indication (OFF) 1 Set the Power Switch to “PRO.”. 2 Press the Select Wheel to display the Menu Screen.
EN 27 1 1 5 S S O 1 3 1 5 F 5 0 F M M S S I I N N IN T . T I M E O 1 1 1 5 F / / F 4 2 S S S S REC T I M E Select Wheel Recording Start/Stop Button REC TIME Menu Display Recording time indicator Interval time indicator INT . TIME Menu MENU Button INT .
28 EN Exposure Control This feature automatically adjusts the iris for the best available picture quality , but you can override it and make the adjustment manually . Manual exposure adjustment is recommended in the following situations: • When shooting using reverse lighting or when the background is too bright.
EN 29 Focus detection zone Focusing AUTO FOCUS The camcorder ’ s Full Range AF system offers continuous shooting ability from close-up to infinity . However , correct focus may not be obtainable in the situations listed below (in these cases use manual focusing): • When two subjects overlap in the same scene.
30 EN Power Switch White Balance Adjustment A term that refers to the correctness of color reproduction under various lighting. If the white balance is correct, all other colors will be accurately reproduced. The white balance is usually adjusted automatically .
EN 31 1 Load a tape ( Z pg. 10). 2 Set the Power Switch to “PLA Y”. T o start playback, press 4 / 6 . • T o stop playback, press 5 . • Press 2 to rewind, or 3 to fast-forward the tape during Stop mode. NOTES: ● The camcorder shuts off automatically after about 5 minutes in Stop mode.
32 EN Set to “PLA Y”. P .AE Button EFFECT Button P .ST ABILIZER Button PLA YBACK Features COUNTER R/M Button Rewind ( 2 ) Button Fast-Forward ( 3 ) Button Play/Pause ( 4 / 6 ) Button Stop ( 5 ) Button T racking: Eliminates noise bars that appear on-screen during playback.
EN 33 PLA YBACK Using The Cassette Adapter Compact video cassette VCR Reels Compartment door Recording safety hole Sliding latch Cassette Adapter (VHS Playpak) Use this to play back an S-VHS-C/VHS-C video cassette recorded with this camcorder on a VHS VCR.
34 EN PLA YBACK Connections These are some basic types of connections. When making connections, refer also to your VCR and TV instruction manuals. Audio cable (optional) T o Audio Output TV VCR (Recording deck) Connector cover* T o TV or VCR T o AUDIO IN * When connecting the cables, open this cover .
EN 35 Basic Connections 1 Make sure all units are turned off. 2 Connect the camcorder to a TV or VCR as shown in the illustration ( Z pg. 34). If using a VCR . . . go to step 3 . If not . . . go to step 4 . 3 Connect the VCR output to the TV input, referring to your VCR’ s instruction manual.
36 EN USING THE REMOTE CONTROL UNIT Installing The Batteries The remote control uses two ”AAA (R03)” size batteries. See “General Battery Precautions” ( Z pg. 46). 1 Open the battery compartment cover as illustrated. 2 Insert two ”AAA (R03)” size batteries in the correct direction.
EN 37 1 1 M / I 2 N S START/STOP REC. TIME INT. TIME FEA TURE: Animation and Time-Lapse PURPOSE: The remote control lets you set/release Interval T ime and Recording T ime without using the Menu Screen. OPERA TION: Animation 1) Set Instead of performing steps 1 through 3 on pg.
38 EN USING THE REMOTE CONTROL UNIT (cont.) w M – 0 : 12 : 34 PLAY STOP INSERT REW START/STOP PAUSE Insert editing indicator Display COUNTER R/M Button T ape Counter RM-V715U (provided) Remote senso.
EN 39 M – 0 : 05 : e 2 4 0 PLAY STOP REW START/STOP PAUSE A.DUB Audio Dubbing Y ou can record a new soundtrack on a prerecorded tape (normal audio only). The sound is recorded from the built- in microphone. Perform steps 1, 2 and 3 of the Insert Editing procedure ( Z pg.
40 EN TROUBLESHOOTING If, after following the steps in the chart below , the problem still exists, please consult your JVC dealer . The camcorder is a microcomputer -controlled device. External noise and interference (from a TV , a radio, etc.) might prevent it from functioning properly .
EN 41 SYMPTOM POSSIBLE CAUSE(S) OTHER During recording, the indications do not appear . The tape will not eject. Some functions are not available. V ertical white lines appear when shooting a very bright object. The picture is blurred in the Quick Review or Retake mode.
42 EN INDEX Controls, Connectors And Indicators T Y 1 i o q u p e r w 2 W Q 3 5 4 6 & ( * y E R R t 7 8 0 @ $ % 9 ! # ^ ).
EN 43 Controls 1 Diopter Adjustment Control ................. Z pg. 15 2 Lens Cover Open/Close Ring ................ Z pg. 16 3 V ideo Light Switch [LIGHT OFF/AUT O/ON] ...................... Z pg. 20 4 5-Second Recording Button [5 SEC. REC] .........
44 EN INDEX Indications 1 R 4 D 2 E 4 5 1 E 0 C 4 M / C M I 2 C I E N S O 2 N P T N 5 W S G . I – R 9 L V P A 9 I H A T G S U U H S L A S T R E A M – E T E C I 1 T . O 1 N : S 4 T + M 5 4 0 W : 0 2 B 18 1X 7 8 9 0 ! @ # & ^ % $ 5 3 4 2 1 * 6 a b 1 T ape Remaining T ime .
EN 45 Indications During Playback TB C M – 0 : S 1 – 2 E : T 3 – 4 1 S : P 23 : 4 4 A 5 T 2 7 4 1 3 5 6 8 1 • : Cassette Indicator Displayed when a tape is loaded. • w : Insert Editing Indicator .................. Z pg. 38 Displayed during Insert Editing.
46 EN CAUTIONS Plug adapter When using the AC Power Adapter/Charger in areas other than the USA n The provided AC Power Adapter/Char ger features automatic voltage selection in the AC range from 1 10 V to 240 V .
EN 47 3. DO NOT leave the unit . . . ... in places of over 50°C (122°F). ... in places where humidity is extremely low . (below 35%) or extremely high (above 80%). ... in direct sunlight. ... in a closed car in summer . ... near a heater . 4. T o protect the unit, DO NOT .
48 EN TERMS A AC Power Adapter/Charger ......................... pg. 8, 9 Animation Recording .............................. pg. 27, 37 Audio Dubbing ............................................. pg. 39 Auto Date Record ...............................
EN 49 N ND Effect Mode ............................................ pg. 22 Nega/Posi Mode ........................................... pg. 22 P Picture Stabilizer ........................................... pg. 18 Power Switch Position ................
50 EN USER MAINTENANCE After Use 1 T urn off the camcorder . 2 Slide EJECT to open the cassette holder , then remove the cassette. 3 Press PUSH to close and lock the cassette holder . 4 Slide BA TTERY RELEASE to remove the battery pack. 5 T urn the LENS COVER Open/Close Ring to close the lens cover .
EN 51 AC Power Adapter/Charger AA-V16U Power requirement : AC 1 10 V to 240 V ` , 50 Hz/60 Hz Power consumption : 23 W Output Charge : DC 8.5 V , 1.3 A VTR : DC 6.
COPYRIGHT© 2000 VICTOR COMPANY OF JAPAN, LTD. UM Printed in Japan 0100MKV * UN * YP VICTOR COMP ANY OF JAPAN, LIMITED EN G R-SX867UM.
An important point after buying a device JVC GR-SX867UM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC GR-SX867UM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC GR-SX867UM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC GR-SX867UM you will learn all the available features of the product, as well as information on its operation. The information that you get JVC GR-SX867UM will certainly help you make a decision on the purchase.
If you already are a holder of JVC GR-SX867UM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC GR-SX867UM.
However, one of the most important roles played by the user manual is to help in solving problems with JVC GR-SX867UM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC GR-SX867UM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
