Instruction/ maintenance manual of the product DAS-TAMP8-SIG AMX
Go to page of 16
Operation/Reference Guide Tango Distributed Audio Tango Amplifiers DAS-TAMP4-SIG DAS-TAMP8-SIG Initial Release: 3/28/2008.
AMX Limited Warranty and Disclaimer This Limited W arranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partn er which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity .
IMPORTANT SAFETY INSTRUCTIONS a T ango Amplifiers IMPORTANT SAFETY INSTRUCTIONS 1. Read instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth.
IMPORTANT SAFETY INSTRUCTIONS b Tango Amplifiers.
Table of Contents i Tango Amplifiers Table of Contents IMPORTANT SAFETY INSTRUCTIONS ................... ............................................. a Tango Amplifiers ........................... .....................................................
ii Tango Amplifiers Table of Contents.
Tango Amplifiers 1 T ango Amplifiers Tango Amplifiers Overview Where more than one pair of speakers is required in T ango Distributed Audio zones, the T ango Amplifier (FIG. 1) provides the extra po wer needed to driv e up to 12 additional speaker pair s or 24 channels per zone.
Tango Amplifiers 2 Tango Amplifiers Tango Amplifiers - Produc t Specifications (Cont.) F ront Panel Componen ts: Light Bar • Blue light bar indicates power status. S tatus LED • Blue LED lights when active Rear P anel Components: Power Switch & Receptacle The master power switch will remain in the ON position normally .
Rack Mounting 3 T ango Amplifiers Rack Mounting Overview T ango units occupy two rack spaces in a standard 19" equipment rack. Rack mountin g brackets and scre ws are located in th e accessories box supplied with the unit. 1. Attach the rack mounting brackets to each side of the T ango unit us ing four M4 screws (supplied) for each bracket.
Rack Mounting 4 Tango Amplifiers.
Wiring and Connections 5 T ango Amplifiers Wiring and Connections Overview - Speaker Wire Technology (SWT) Speaker W ire T echnology (SWT) allows both data and audio si gnals to tra vel over the same four conductor wire. This remarkable technology removes the need for control wire since the cont rol and audio signals are shared on the same wire.
Wiring and Connections 6 Tango Amplifiers Cabling Instructions This installation uses lo w v oltage cabling similar to telephone and al arm wiring, and as such does not commonly hav e very man y restricti ons on their installation. Howe ver rules may vary in dif ferent regions.
Wiring and Connections 7 T ango Amplifiers Connecting To a Tango Audio Controller Connect the T ango Amplifier to the T ango Audio C ontroller via the 4-pin connector labelled “ From Controller ” on the rear panel of the Amplif ier .
Wiring and Connections 8 Tango Amplifiers.
Wiring and Connections 9 Tango Amplifiers.
3/08 © 2008 AMX. All rights reserved. AMX and the AM X logo are register ed trademarks of AMX. AMX reserves the right to alter specifica tions without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.
An important point after buying a device AMX DAS-TAMP8-SIG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AMX DAS-TAMP8-SIG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AMX DAS-TAMP8-SIG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AMX DAS-TAMP8-SIG you will learn all the available features of the product, as well as information on its operation. The information that you get AMX DAS-TAMP8-SIG will certainly help you make a decision on the purchase.
If you already are a holder of AMX DAS-TAMP8-SIG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AMX DAS-TAMP8-SIG.
However, one of the most important roles played by the user manual is to help in solving problems with AMX DAS-TAMP8-SIG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AMX DAS-TAMP8-SIG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
