Instruction/ maintenance manual of the product BR-DV600E JVC
Go to page of 24
This instruction book is made from 100% recycled paper. INSTRUCTIONS VIDEO CASSETTE RECORDER BR-DV600U SL96179 For Customer Use: Enter below the Serial No. which is located on the bottom of cabinet. Retain this information for future reference. Model No.
2 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
3 CAUTION ATTENTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE D’ELECTROCUTION NE PAS OUVRIR INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
4 CONTENTS 1 INTRODUCTION 1-1 Major Features ............................................. 5 1-2 Maintenance ................................................ 5 1-3 Precautions .................................................. 6 2 CONTROLS, CONNECTORS AND DISPLAYS 2-1 Front Panel .
6 1-3 Precautions Handling 5 Do not block the ventilation openings. 5 Do not place anything heavy on the unit. 5 Do not put any foreign materials into the cassette loading slot. 5 Operate the unit in a horizontal (flat) position only . 5 Avoid violent shocks to the unit.
8 2-2 Rear Panel 2 CONTROLS, CONNECTORS AND DISPLA YS DC 12V PGZ01945 TIMER TIME CODE SPARE COMPONENT VIDEO SYNC IN REC OFF PLAY DV IN/OUT REMOTE AUDIO 2 1 SERIAL CH 1/3 OUT OUT IN IN B-Y IN Y/C LINE .
11 3-1 Video system connections 3 CONNECTIONS Connecting a monitor The on-screen display can be viewed on a monitor con- nected to the [VIDEO MONITOR OUT] connector . Connecting video equipment Connect the video device to the appropriate connector (4 types are available).
12 DC 12V PGZ01945 TIMER TIME CODE SPARE COMPONENT VIDEO SYNC IN REC OFF PLAY DV IN/OUT REMOTE AUDIO 2 1 SERIAL CH 1/3 OUT OUT IN IN B-Y IN Y/C LINE OUT OUT MONITOR CH 2/4 MONITOR OUT R-Y Y 3-2 Audio system connections 3 CONNECTIONS Audio output from a VCR, etc.
14 EDITING CONTROL UNIT RM-G800 EDIT MODE ENTRY MENU CANCEL GOTO IN OUT ENTRY SHI FT PREVIEW REVIEW AUTO EDIT ALL STOP GPI MANUAL TAKE COUNTER TC HOLD TC CTL UB PRESET ASSEM VIDEO/Hi-Fi AUD-1 AUD-2 IN.
16 Recorder BR-DV600 BR-DV600 BR-S800 SR-S365 (U MODEL) SR-S388 (E MODEL) BR-DV600 Player BR-DV600 BR-DV600 BR-DV600 BR-DV600 BR-S800/BR-S500 (+ SA-N50)* 5 Edit adjust setting The No. 353 <EDIT ADJUST> menu switch must be adjusted according to the configuration of the editing system being used.
18 4 MENU SWITCHES 4-2 Menu switch details For switch setting procedures, refer to “ Menu switch setting procedure ” . q : Factory setting (00): The number in the bracket shows the set value on the counter display . 002 OPERA TION LOCK Details: Switches the operation lock ON/OFF .
20 4 MENU SWITCHES 4-2 Menu switch details 502 CHARACTER V .POSITION Details: Moves the display position of the tape counter on screen, etc. vertically .
22 Built-in clock setting Time data is recorded in the sub code area of the tape during recording. In the Play mode, this data is read out and can be shown on the on-screen display or the counter display . 5 PREP ARA TION 5 Setting procedure The names of the operation buttons are shown above the buttons.
24 PHONES MIC REMOTE LOCAL EJECT OPERATE REC LEVEL CH-2/4 CH-1/3 SHIFT SET SELECT SHIFT MENU HOLD AUDIO MONITOR OUTPUT COUNTER SHIFT A. DUB ADVANCE PRESET L CTL TC UB CH-1/2 CH-3/4 R MIX MIX REW STOP .
26 8 EXTERNAL TIMER-ST ART FUNCTION DC 12V PGZ01945 TIMER TIME CODE SPARE COMPONENT VIDEO SYNC IN REC OFF PLAY DV IN/OUT REMOTE AUDIO 2 1 SERIAL CH 1/3 OUT OUT IN IN B-Y IN Y/C LINE OUT OUT MONITOR CH 2/4 MONITOR OUT R-Y Y REC: Timer recording OFF: Timer function OFF PLA Y: Timer playback Commercially available timer, etc.
28 9 TIME CODE Set the menu switches. ( See page 20.) 5 Set the No. 414 <TCG SELECT> menu switch to “ PRESET ” . 5 Set the No. 415 <TCG MODE> menu switch. Setting is not necessary for user bits. REC RUN: The time code is counted only during recording.
30 10 SUPER SCENE FINDER FUNCTION Preparation Connect the 9-pin D-sub connector of the installed SA-K46 RS-232C interface board to a personal computer , etc. with an RS-232C cable. Use a reverse type cable. For RS-232C interface settings, refer to “ RS-232C specifications ” on page 32.
32 11-2 RS-232C specifications 9PIN D-Sub 1 23 4 5 6 9 Pin NO. Signals Operations Direction of signals 2 RXD Receive data VTR p PC 3 TXD Transmit data VTR [ PC 4 DTR Data terminal ready VTR [ PC 5 GND Signal ground 6 DSR Data set ready VTR p PC Note: PC means a controller such as a personal computer.
34 11 RS-232C INTERF ACE Commands Description B6 R-SHUTTLE Shuttle reverse play . The search speed is specified by sending the speed code data after this command (see the table above). C4 FULL EE ON Full EE mode ON C5 FULL EE OFF Full EE mode OFF CA REC Record.
36 11 RS-232C INTERF ACE Contents of ST A TUS SENSE When the ST ATUS SENSE (D7H) command is sent, the following data (5 bytes) is returned. First byte Bit No. Status When the bit is 1 7 Always 1 6 Always 0 5 SHORT FF/REW D uring short FF or short REW 4 REC INHIBIT Recording is inhibited.
38 11 RS-232C INTERF ACE Menu switch setting command ED MEMORY SW PRESET Use this command to change the VCR ’ s menu switches. Transmit the data (3 bytes) corresponding to the menu switch to be changed, following this command. (e.g.) Set No. 108 <VIDEO INPUT SELECT> menu switch to “ COMPONENT ” .
40 12 TROUBLESHOOTING 12-1 Warning indicators If the unit malfunctions during operation, the built-in self-diagnostics system identifies the problem and displays a warning message on the monitor and/or the counter display . Also, the [AUTO OFF] indicator may be shown on the LCD.
42 12-2 Other problems Action • Set the [REMOTE] switch to “ LOCAL ” . • Set the No. 002 <OPERA TION LOCK> menu switch to “ OFF ” . • Connect the monitor to the [MONIT OR OUT] connector . • Set the No. 500 <ON SCREEN> menu switch to “ ON ” .
44 Precautions for Use of Head Cleaning Tape Adhere to the following precautions when using the head cleaning tape. 1. The tape runs for 10 seconds at a time in the PLAY mode. (The tape stops automatically.) Press the PLAY button after the cleaning tape is fully loaded.
An important point after buying a device JVC BR-DV600E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought JVC BR-DV600E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data JVC BR-DV600E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, JVC BR-DV600E you will learn all the available features of the product, as well as information on its operation. The information that you get JVC BR-DV600E will certainly help you make a decision on the purchase.
If you already are a holder of JVC BR-DV600E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime JVC BR-DV600E.
However, one of the most important roles played by the user manual is to help in solving problems with JVC BR-DV600E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device JVC BR-DV600E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
