Instruction/ maintenance manual of the product LT2218A Jonsered
Go to page of 32
Operator's Manual L T2218A.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 PRODUCT SPECIFICA TIONS Gasoline Capacity 1.5 Gallons (5,68 L) and type: Unleaded Regular Oil T ype (API-SG-SL): SAE 30 (above 32°F/0°C) SAE 5W -30 (below 32°F/0°C) Oil Capacity: W/Filter: 56 0z. W/O Filter: 48 oz. Spark Plug: Champion RC12YC (Gap: .
5 UNAS SEMBLED P ARTS Steering Wheel Steering Wheel (1) W asher Seat (1) Seat Steering Boot Steering Extension Shaft Steering Wheel Adapter K ey(s) Slope Sheet (1) Oil Drain T ube F or Future Use (1) .
6 AS SEMBL Y TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier . Stan dard wrench sizes are listed. (1) 3/4" wrench Pliers (2) 7/16" wrenches Tire pressure gauge (1.
7 AS SEMBL Y Fig. 3 BOL T FL A T WASHER SEA T P AN PA D T APE SL OT TA B ADJUSTMENT HANDLE Fig. 4 TO CHECK BA TTERY (See Fig. 4) • Lift seat to raised position. NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps.
8 AS SEMBL Y ✓ CHECKLIST BEFORE YOU OPERA TE Y OUR NEW TRAC TOR, WE WISH TO ASSURE THA T YOU RECEIVE THE BEST PER- FORMANCE AND SA TISF ACTION FROM THIS QUALITY PRODUCT . PLEASE REVIEW THE FOLL OWING CHECKLIST : ✓ All assembly instructions have been com plet ed.
9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
10 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
11 OPERA TION 00155 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op- erating your tractor or per form ing any adjustments or repairs.
12 Fig. 10 OPERA TION TO ADJUST MOWER CUTTING HEIGHT (See Fig. 10) The position of the attachment lift lever (A) determines the cutting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4".
13 OPERA TION TO OPERA TE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills.
14 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time.
15 OPERA TION MOWING TIPS • Tire chains cannot be used when the mower hous ing is attached to tractor . • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.
16 MAINTENANCE LUBRICA TION CHART 01964 ➀ FRONT WHEEL BEARING ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ SPINDLE ZERK ➀ SPINDLE ZERK ➀ GENERAL PURPOSE GREASE ➁ REFER TO MAINTENANCE “ENGINE” SECTION IMPORT ANT : DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HA VE SPECIAL NYLON BEARINGS.
17 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
18 MAINTENANCE TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. T o prevent pos - si ble damage to seals, do not use high pressure water or steam to clean transmission.
19 MAINTENANCE CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine dam age from overheating. Clean with a wire brush or compressed air to re move dirt and stubborn dried gum fibers. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage.
20 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key .
21 SERVICE AND ADJUSTMENTS M C D A E F B • A TT ACH FRONT LINK (E) - Work from left side of trac- tor . Insert rod end of link assembly through front hole in tractor front suspension bracket (F). • Insert end of link (E) into hole in front mower bracket (H) and secure with washer and retainer spring (J).
22 FRONT - TO-BACK ADJUSTMENT (See Figs. 28 & 29) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
23 SERVICE AND ADJUSTMENTS TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 30) MOWER DRIVE BEL T REMOV AL • P ark tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.
24 SERVICE AND ADJUSTMENTS Fig. 32 0 0663 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO REMOVE WHEEL FOR REP AIRS (See Fig. 32) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).
25 SERVICE AND ADJUSTMENTS Fig. 34 Fig. 35 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
28 TROUBLESHOOTING POINTS Engine continues to run 1. F aulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department.
29 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
30 SERVICE NOTES.
31 SERVICE NOTES.
532 42 71-56 02.12.09 BAD Printed in the U.S.A. Jonsered Motor AB, S-433 81 P artille, Sweden..
An important point after buying a device Jonsered LT2218A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jonsered LT2218A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jonsered LT2218A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jonsered LT2218A you will learn all the available features of the product, as well as information on its operation. The information that you get Jonsered LT2218A will certainly help you make a decision on the purchase.
If you already are a holder of Jonsered LT2218A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jonsered LT2218A.
However, one of the most important roles played by the user manual is to help in solving problems with Jonsered LT2218A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jonsered LT2218A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
