Instruction/ maintenance manual of the product AT-3303-J John Deere
Go to page of 32
4-Inch Angle Grinder Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE ANGLE GRINDER AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
2 4-Inch Angle Grinder Operator's Manual Congratulations on the purchase of your new John Deere 4-Inch Angle Grinder! You can be assured your angle grinder was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance.
4-Inch Angle Grinder Operator's Manual 3 T able of Content INTRODUCTION .................................................................................................... 2 TABLE OF CONTENTS .....................................................
4 4-Inch Angle Grinder Operator's Manual READ OPERATING INSTRUCTIONS Always become familiar with all the instructions and warnings before operating any pneumatic tool. RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your pneumatic tool or in this manual, be alert to the potential for personal injury.
4-Inch Angle Grinder Operator's Manual 5 ALWAYS WEAR APPROVED EYE PROTECTION Impact resistant eye protection should meet or exceed the standards as set forth in the United States ANSI Z87.1, Occupational and Educational Eye and Face Protection. Look for the marking Z87.
6 4-Inch Angle Grinder Operator's Manual AVOID PROLONGED EXPOSURE TO VIBRATION Pneumatic tools can vibrate during use. Prolonged exposure to vibration or very repetitive hand and arm movements, can cause injury. Stop using any tool if discomfort, tingling feeling or pain occurs.
4-Inch Angle Grinder Operator's Manual 7 Always use clean dry air. Excessive moisture and dirt will greatly reduce the life of any air motor. We recommend the installation of an in-line filter-regulator-lubricator as close to the tool as possible.
8 4-Inch Angle Grinder Operator's Manual Maintenance LUBRICATION: An automatic in-line filter-regulator-lubricator is recommended as it increases tool life and keeps the tool in sustained operation. The in-line lubricator should be regularly checked and filled with John Deere A T-4003 air tool oil.
4-Inch Angle Grinder Operator's Manual 9 T roubleshooting Specifications Loss of Power 1. Low air pressure 2. Improper lubrication or dirt build up 3.
10 4-Inch Angle Grinder Operator's Manual Limited Warranty John Deere Two-Year Limited Warranty. John Deere Grinder, Models covered in this manual, are warranted by John Deere to the original user against defects in workmanship or materials under normal use for two years after date of purchase.
4-Inch Angle Grinder Operator's Manual 11 Product Suitability. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary from those in neighboring areas.
12 4-Inch Angle Grinder Operator's Manual Félicitations de l'achat de votre nouveau la meuleuse d’angle! Vous pouvez être assuré que votre nouveau la meuleuse d’angle été construit avec le plus haut niveau de précision et de fiabilité.
4-Inch Angle Grinder Operator's Manual 13 T able Des Matieres INTRODUCTION .................................................................................................... 12 TABLE DES MATIERESRE ..............................................
14 4-Inch Angle Grinder Operator's Manual Sécurité RECONNAÎTRE LES SYMBOLES DE MISE EN GARDE Voici le symbole de mise en garde. Lorsqu'il apparaît sur la outil pneumatique ou dans la présente publication, c'est pour prévenir d'un risque potentiel de blessure.
4-Inch Angle Grinder Operator's Manual 15 PORTEZ TOUJOURS DES LUNETTES DE PROTEC- TION HOMOLOGUÉES Les lunettes de protection antichoc doivent être au moins conformes à la norme ANSI Z87.1 relative à la protection des yeux et du visage sur les lieux de travail et d’appren- tissage.
16 4-Inch Angle Grinder Operator's Manual ÉVITEZ UNE EXPOSITION PROLONGÉE AUX VIBRATIONS Les outils pneumatiques peuvent vibrer en cours de fonctionnement. Une exposition prolongée aux vibrations ou des mouvements très répétitifs de la main et du bras peuvent provoquer des blessures.
4-Inch Angle Grinder Operator's Manual 17 L’outil est conçu pour fonctionner à une pression de 620 kPa. Son fonctionnement à une pression inférieure rend l’outil moins performant, alors q.
18 4-Inch Angle Grinder Operator's Manual Fonctionnement Entretien GRAISSAGE: Il est recommandé d’installer un filtre régulateur graisseur sur la conduite d’alimentation d’air pour prolonger la durée de vie de l’outil et assurer un bon fonctionnement continu de celuici.
4-Inch Angle Grinder Operator's Manual 19 Dépannage Spécifications Meules ------------------------------------------- 4" (10 cm) type 27 Dimensions des meules --------------------- 4 po x 1/4 po x 5/8 po Taille de l’arbre -------------------------------- 3/8 po - 24 Vitesse libre ------------------------------------ 11.
20 4-Inch Angle Grinder Operator's Manual Garantie limitée Garantie limitée deux John Deere. Les modèles de meuleuse John Deere, traités dans ce manuel sont garantis par John Deere contre tou.
4-Inch Angle Grinder Operator's Manual 21 Appropriation du produit. De nombreuses juridictions possèdent des codes et une législation concernant la vente, la construction, l’installation et/ou l’utilisation particulière de produits pouvant différer de celles en vigueur dans les régions voisines.
22 4-Inch Angle Grinder Operator's Manual Introduccion ¡Felicitaciones por la compra de su nueva la esmeriladora de ángulo! Puede estar seguro que su la esmeriladora de ángulo fue construida con el nivel más alto de precisión y exactitud.
4-Inch Angle Grinder Operator's Manual 23 T abla de Materias INTRODUCCION .................................................................................................... 22 TABLA DE MATERIAS ..................................................
24 4-Inch Angle Grinder Operator's Manual Seguridad Estos párrafos están rodeados por una “CASILLA DE ALERTA DE SEGURIDAD”. Esta casilla se usa para designar y enfatizar las Advertencias de Seguridad que deben seguirse al operar esta herramienta.
4-Inch Angle Grinder Operator's Manual 25 SIEMPRE USE PROTECCIÓN PARA LOS OJOS APROBADA La protección para los ojos, resistente al impacto, tiene que cumplir o exceder los estándares estableci- dos en ANSI Z87.1 de Estados Unidos sobre la Protección de los Ojos y de la Cara en el Trabajo y la Educación.
26 4-Inch Angle Grinder Operator's Manual EVITE LA EXPOSICIÓN PROLONGADA A LA VIBRACIÓN Las herramientas neumáticas pueden vibrar durante el uso. La exposición prolongada a la vibración o los movimientos de las manos o de los brazos muy repetidos pueden producir lesiones.
4-Inch Angle Grinder Operator's Manual 27 Instalación La herramienta ha sido diseñada para operar a 620 kPa, por lo tanto, la presión más baja (por debajo de 620 kPa) reducirá su rendimiento.
28 4-Inch Angle Grinder Operator's Manual Mantenimiento LUBRICACION Se recomienda usar un filtro-regulador-lubricador en línea para prolongar la duración de la herramienta y mantenerla funcionando correctamente. El lubricador en línea se debe revisar regularmente y se debe llenar con aceite para herramientas de aire John Deere AT-4003.
4-Inch Angle Grinder Operator's Manual 29 Localizacion de Fallas Solucion Síntoma Causa(s) Posible(s) Pérdida de energía 1. Revise el abastecimiento de aire. Se necesita la presión de aire de 620 kPa en la herramienta cuando está operando, para lograr el rendimiento de capacidad nominal.
30 4-Inch Angle Grinder Operator's Manual Garantía Limitada Garantía Limitada de John Deere por Dos Año. Esmeriladora de Matrices John Deere, y los Modelos tratados en este manual están garan.
4-Inch Angle Grinder Operator's Manual 31 Uso adecuado del producto . Muchas jurisdicciones tienen códigos o reglamentos que regulan las ventas, fabricación, instalación y/o uso del producto para ciertos usos específicos, los cuales pueden variar en áreas circunvecinas.
32 4-Inch Angle Grinder Operator's Manual #37-0651-090403 © Copyright 2003. John Deere Manufactured for Deere & Company Moline, Illinois 61265 4-Inch Angle Grinder.
An important point after buying a device John Deere AT-3303-J (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought John Deere AT-3303-J yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data John Deere AT-3303-J - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, John Deere AT-3303-J you will learn all the available features of the product, as well as information on its operation. The information that you get John Deere AT-3303-J will certainly help you make a decision on the purchase.
If you already are a holder of John Deere AT-3303-J, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime John Deere AT-3303-J.
However, one of the most important roles played by the user manual is to help in solving problems with John Deere AT-3303-J. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device John Deere AT-3303-J along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
