Instruction/ maintenance manual of the product AT 3702-J John Deere
Go to page of 32
Air Hammer Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE AIR HAMMER AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
2 Air Hammer Operator's Manual Congratulations on the purchase of your new air hammer! You can be assured you air hammer was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance.
Air Hammer Operator's Manual 3 T able of Content INTRODUCTION .................................................................................................... 2 TABLE OF CONTENTS ...............................................................
4 Air Hammer Operator's Manual READ OPERATING INSTRUCTIONS Always become familiar with all the instructions and warnings before operating any pneumatic tool. RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your pneumatic tool or in this manual, be alert to the potential for personal injury.
Air Hammer Operator's Manual 5 ALWAYS WEAR APPROVED EYE PROTECTION Impact resistant eye protection should meet or exceed the standards as set forth in the United States ANSI Z87.1, Occupational and Educational Eye and Face Protection. Look for the marking Z87.
6 Air Hammer Operator's Manual AVOID PROLONGED EXPOSURE TO VIBRATION Pneumatic tools can vibrate during use. Prolonged exposure to vibration or very repetitive hand and arm movements, can cause injury. Stop using any tool if discomfort, tingling feeling or pain occurs.
Air Hammer Operator's Manual 7 Always use clean dry air. Excessive moisture and dirt will greatly reduce the life of any air motor. We recommend the installation of an in-line filter-regulator-lubricator as close to the tool as possible. A 3/8" air hose is required up to a length of 8 ft.
8 Air Hammer Operator's Manual Maintenance Operation LUBRICATION: An automatic in-line filter-regulator-lubricator is recommended as it increases tool life and keeps the tool in sustained operation. The in-line lubricator should be regularly checked and filled with John Deere AT-4003 air tool oil.
Air Hammer Operator's Manual 9 T roubleshooting Specifications Loss of Power 1. Low air pressure 2. Improper lubrication or dirt build up 3. Worn motor parts, or other problems 1. Check air supply. For rated performance, 90 PSI air pressure is required at the tool, with tool operating 2.
10 Air Hammer Operator's Manual Limited Warranty John Deere Two-Year Limited Warranty. John Deere Air Hammer, Models covered in this manual, are warranted by John Deere to the original user against defects in workmanship or materials under normal use for two years after date of purchase.
Air Hammer Operator's Manual 11 Product Suitability. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary from those in neighboring areas.
12 Air Hammer Operator's Manual Félicitations de l'achat de votre nouveau la marteau pneumatiquet! Vous pouvez être assuré que votre nouveau la marteau pneumatique a été construit avec le plus haut niveau de précision et de fiabilité.
Air Hammer Operator's Manual 13 T able Des Matieres INTRODUCTION .................................................................................................... 12 TABLE DES MATIERESRE ........................................................
14 Air Hammer Operator's Manual Sécurité RECONNAÎTRE LES SYMBOLES DE MISE EN GARDE Voici le symbole de mise en garde. Lorsqu'il apparaît sur la outil pneumatique ou dans la présente publication, c'est pour prévenir d'un risque potentiel de blessure.
Air Hammer Operator's Manual 15 PORTEZ TOUJOURS DES LUNETTES DE PROTEC- TION HOMOLOGUÉES Les lunettes de protection antichoc doivent être au moins conformes à la norme ANSI Z87.1 relative à la protection des yeux et du visage sur les lieux de travail et d’appren- tissage.
16 Air Hammer Operator's Manual ÉVITEZ UNE EXPOSITION PROLONGÉE AUX VIBRATIONS Les outils pneumatiques peuvent vibrer en cours de fonctionnement. Une exposition prolongée aux vibrations ou des mouvements très répétitifs de la main et du bras peuvent provoquer des blessures.
Air Hammer Operator's Manual 17 L’outil est conçu pour fonctionner à une pression de 620 kPa. Son fonctionnement à une pression inférieure rend l’outil moins performant, alors que son fon.
18 Air Hammer Operator's Manual Fonctionnement Entretien GRAISSAGE: Il est recommandé d’installer un filtre régulateur graisseur sur la conduite d’alimentation d’air pour prolonger la durée de vie de l’outil et assurer un bon fonctionnement continu de celuici.
Air Hammer Operator's Manual 19 Dépannage Spécifications Vite sse ------------------------------------------------- 2,000 cps/mn Taille des burins ------------------------------------- Tige de .
20 Air Hammer Operator's Manual Garantie limitée Garantie limitée deux John Deere. Les modèles le marteau pneumatiques John Deere, traités dans ce manuel sont garantis par John Deere contre t.
Air Hammer Operator's Manual 21 Appropriation du produit. De nombreuses juridictions possèdent des codes et une législation concernant la vente, la construction, l’installation et/ou l’utilisation particulière de produits pouvant différer de celles en vigueur dans les régions voisines.
22 Air Hammer Operator's Manual Introduccion ¡Felicitaciones por la compra de su nueva de martillo neumático! Puede estar seguro que su nueva de martillo neumático fue construida con el nivel más alto de precisión y exactitud.
Air Hammer Operator's Manual 23 T abla de Materias INTRODUCCION .................................................................................................... 22 TABLA DE MATERIAS ............................................................
24 Air Hammer Operator's Manual Seguridad Estos párrafos están rodeados por una “CASILLA DE ALERTA DE SEGURIDAD”. Esta casilla se usa para designar y enfatizar las Advertencias de Seguridad que deben seguirse al operar esta herramienta.
Air Hammer Operator's Manual 25 SIEMPRE USE PROTECCIÓN PARA LOS OJOS APROBADA La protección para los ojos, resistente al impacto, tiene que cumplir o exceder los estándares estableci- dos en ANSI Z87.1 de Estados Unidos sobre la Protección de los Ojos y de la Cara en el Trabajo y la Edu-cación.
26 Air Hammer Operator's Manual EVITE LA EXPOSICIÓN PROLONGADA A LA VIBRACIÓN Las herramientas neumáticas pueden vibrar durante el uso. La exposición prolongada a la vibración o los movimientos de las manos o de los brazos muy repetidos pueden producir lesiones.
Air Hammer Operator's Manual 27 Instalación La herramienta ha sido diseñada para operar a 620 kPa, por lo tanto, la presión más baja (por debajo de 620 kPa) reducirá su rendimiento y la pres.
28 Air Hammer Operator's Manual ANTES DE LA OPERACIÓN: Antes de que se conecte la herramienta al abastecimiento de aire, despeje la acumulación de polvo y de humedad de la manguera de aire. Antes de remover una herramienta para darle servicio o de cambiar accesorios, asegúrese que la tubería de aire esté cerrada y sin aire.
Air Hammer Operator's Manual 29 Localizacion de Fallas Solucion Síntoma Causa(s) Posible(s) Pérdida de energía 1. Revise el abastecimiento de aire. Se necesita la presión de aire de 620 kPa en la herramienta cuando está operando, para lograr el rendimiento de capacidad nominal.
30 Air Hammer Operator's Manual Garantía Limitada Garantía Limitada de John Deere por Dos Año. Martillo Neumático John Deere, y los Modelos tratados en este manual están garantizados por John Deere para el comprador original contra defectos en la fabricación o el material bajo uso normal por dos año a partir de la fecha de compra.
Air Hammer Operator's Manual 31 Uso adecuado del producto . Muchas jurisdicciones tienen códigos o reglamentos que regulan las ventas, fabricación, instalación y/o uso del producto para ciertos usos específicos, los cuales pueden variar en áreas circunvecinas.
32 Air Hammer Operator's Manual #37-0731-090403 © Copyright 2003, John Deere Manufactured for Deere & Company Moline, Illinois 61265 Long Barrel Air Hammer.
An important point after buying a device John Deere AT 3702-J (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought John Deere AT 3702-J yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data John Deere AT 3702-J - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, John Deere AT 3702-J you will learn all the available features of the product, as well as information on its operation. The information that you get John Deere AT 3702-J will certainly help you make a decision on the purchase.
If you already are a holder of John Deere AT 3702-J, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime John Deere AT 3702-J.
However, one of the most important roles played by the user manual is to help in solving problems with John Deere AT 3702-J. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device John Deere AT 3702-J along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
