Instruction/ maintenance manual of the product DC-650CRC Jet Tools
Go to page of 20
Operating Instructions and Parts Manual Dust Collector Model: DC-650A/C/ARC/CRC DC-650ARC shown DC-650C shown WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No.
2 This manual has been pre pared for the owner and operato r s of the JET DC-650 Series Dust Collectors. I ts purpose, aside from machine operatio n, is to prom ote safety using accepted operatin g and maintenance procedures.
3 Table of Contents Warranty and Service ........................................................................................................... ................................ 2 Table of Contents .................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and un derstand the warnings posted on the machi ne and in this manual. Failure to co mply with all of these warnings may cause serious inju ry.
5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king arou nd, carrying on a conversation a nd “horse-play” are careless acts that can result in seriou s injury.
6 Introduction This manual is provided by JET covering the safe operation and maintenan ce procedures for models DC-650 Series Dust Collectors. This manual contains in structions on installation, safety pre cautions, general operating procedures, maintenance in structions and par ts breakdown.
7 Unpacking 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly.
8 Assembly The dust collector must be disconnected from the po wer source during assembly . Failure to comply may result in serious injury! Motor Housing and Support Canister 1. Place the impeller housing (A, Fig. 1) on the floor with the motor (B, Fig.
9 Filter Bag Installation – DC-650A/ARC 1. Thread an M6 hex nut onto the filter bag support rod, followed by an M6 fl at washer and M6 lock washer (A, Fig. 5). Thread the support rod (B, Fig. 5) into the motor/fan housin g and tighten nut against the housing.
10 Canister Installation – DC-650C/CRC 1. Place the canister filter so that it fits snugly over the housing and tighten the four knobs (A, Fig. 7). 2. Mount handle (B, Fig. 7) to the arm (C, Fig. 7) with a M8 flat washer (D, Fig. 7), M8 lock washer (E, Fig.
11 Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disco nnected from the power source, unplugged. Failu re to comply may result in serious injury! The DC-650 series dust collectors are rated at 115/230V, Prewired 115V .
12 Maintenance Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter Bag – DC-650A/ARC Wearing a particle mask/respirator for protection against fin e dust particles during cleaning is highly recommended.
13 Parts Replacement Parts Replacement parts are li sted in the Parts List on the following pages. To orde r parts or reach our service department, call 1-800-274-68 48 between 7:00 a.
14 Index No. Part No. Description Size Qty 35 ............. 331010 ..................... Shaft ....................................................................................................................... 1 36 ............. 331043 ..........
15 Parts Breakdown for DC-650C/ CRC Models for DC-650A/AR C Models.
16 Remote Control Breakdown for DC-650ARC/CRC Index No. Part No. Description Size Qty ................. DC650RC-100 ......... Rec eiver As sembly (Ite ms 1-11) ............................................................ ................ 1 1 .........
17 Wiring Diagrams DC-650A/C Models 115V 230V.
18 DC-650ARC/CRC Models.
19 Notes.
20 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m.
An important point after buying a device Jet Tools DC-650CRC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools DC-650CRC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools DC-650CRC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools DC-650CRC you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools DC-650CRC will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools DC-650CRC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools DC-650CRC.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools DC-650CRC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools DC-650CRC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
