Instruction/ maintenance manual of the product 719T WMH Jet Tools
Go to page of 20
Operating Instructions and Parts Manual Tilting Table Hollow Chisel Mortiser Model: 719T WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No.
2 This manual has been prepared for the owner and operators of a POWE RMATIC 719T Tilting Ta ble Hollow Chisel Mortiser. Its purpose, aside from ma chi ne operation, is to promote safety using accepte d operating and maintenance procedures.
3 Table of Contents Warranty and Service ........................................................................................................... ......................... 2 Table of Contents ........................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the m a chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 blahblahblah 21. Make your workshop child proof with padlocks , master switches or by removing starter keys. 22. Give your work undivided attention. Looking a roun d, carrying on a conversation and “horse -play” are careless acts that can result in seriou s injury.
6 Introduction This manual is provided by POWE RMATIC covering the safe operation and mai ntenance procedures for a Model 719T Tilting Table Hollow Ch isel Mortiser. Th is manual contain s instructions on installation, safety precautions, general operating procedures, ma intenance instructions and parts breakdown.
7 Unpacking Remove mortiser and stand from the shipping ca rtons. Check for damage and ensure all part s are intact. Any damage should be reported immediately to your distributor and shippin g agent. Read the manu al thoroughly to familiarize y ourself with the correct assembly a nd maintenance procedures and proper safety precautions.
8 Assembly Do not connect the machine to power source until c ompletely assembled. Read and understand the entire manual. Securing Machine to Stand The mortiser should be secured to the stand with four M8 x 45 hex cap screws and M8 lock washers (pro vided) using the holes in the base.
9 Installing Chisel and Bit Referring to Figure 3 : 1. Loosen the lock screw . 2. Insert the chisel bushing into the head with the hole facing forward to line up with the lock screw . Screw in the lock screw just enough so the screw extends into th e hole of the bushing , holding it in place.
10 Electrical Power Connection Do not operate this machine in damp locations. A separate electrical circui t should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
11 Adjustments 90 ° Chisel to Worktable Calibration Referring to Figure 7: Place a square (E) so it rests a gainst the worktable (B) and chisel (A). If the chisel to table angle is 90 ° , no calibration is necessary. If calibration is required: 1. Loosen the bolt (C) that allows the tilting base to pivot.
12 6. Reinstall the chisel bus hing (F) and se cure it loosely with the lock screw (E). 7. Reinstall the chisel and bit (refer to the Installing Chisel and Bit section ) . Depth Stop Rod Adjustment Referring to Figure 9: A depth stop rod (A) is provided to li mit the depth of the chisel.
13 Chisel Parallel to Workpiece Referring to Figure 11: The chisel can be adjusted parallel to the workpiece as follows: 1. With the left handwheel (A), move the t able back far enough to insert the wo rkpiece (B) between the chisel (D) and fence . 2.
14 Do not have the chisel slot against the blind end of the mortise, as the chips will not be able to clear the chisel. This can cause ov erheating and possible breakage of chisel or bit. When cutting deep mortises, make the cut in several stages of approximately 1" each, to allow chips to clear.
15 three turns of the cutter in a carpenter' s brace chuck should be en ough to sharpen th e chisel, as shown in Figure 16. Use a small, triangular, smooth file to reliev e the inner corners of the chi sel (Figure 17). Remove any burrs from the outsi de of the chisel with a fine oilstone.
16 719T Mortiser Parts List Index No. Part No. Description Size Qty ................. 2474002T ................. 719T Mortiser Assy (Items 1 thru 120) .............. ................................ ................. 1 1 ............... 719T-101 .....
17 Index No. Part No. Description Size Qty 57 ............. 6294180 ................... C-Clip ................................................................... ................................................. 2 58 ............. 6294181 ...........
18 Index No. Part No. Description Size Qty 114 ........... TS-1491021 ............. Hex Ca p Screw .................................................... M10 x 20 ................. ................. 4 115 ........... 719T-1115 ................ Tilt ing Bracket .
19 719T Mortiser Stand Parts List Index No. Part No. Description Size Qty ................. 6294235T ................. Stand Assembly (Items 1 thru 8).......................... ............................ ..................... 1 1 ............... 719T-201 .
20 Optional Accessories Index No. Part No. Description ................. 6294232 ................... Chuck Extension Adapto r Kit (Items 1 thru 3)...... .................................. ................. 1 ............... 6294210 ...................
An important point after buying a device Jet Tools 719T WMH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet Tools 719T WMH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet Tools 719T WMH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet Tools 719T WMH you will learn all the available features of the product, as well as information on its operation. The information that you get Jet Tools 719T WMH will certainly help you make a decision on the purchase.
If you already are a holder of Jet Tools 719T WMH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet Tools 719T WMH.
However, one of the most important roles played by the user manual is to help in solving problems with Jet Tools 719T WMH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet Tools 719T WMH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
