Instruction/ maintenance manual of the product PB-150 Jet
Go to page of 28
Operating Instructions and Parts Manual Portable Horizontal Bandsaws Models PB-85 and PB-150 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No.
2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it se lls. If one of our tools nee ds service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service.
3 Table of Contents Warranty and Service .................................................................................... Error! Bookmark not defined. Table of Contents ..............................................................................
4 Warning 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the m a chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 blahblahblah 21. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 22. Give your work undivided attention. Loo king aroun d, carrying on a conversation and “ho rse-play” are careless acts that can result in serious inj ury.
6 Introduction This manual is provided by WMH Tool Grou p covering the safe operation and maintena nce procedures for a JET Model PB-85 or PB-1 50 Band Saw. This manual contains instructions on install ation, safety precautions, general o perating procedures, mainten ance instructions a nd parts breakd own.
7 Features and Terminology Model PB-85 is shown; featur es are similar for the PB-150..
8 Unpacking Open shipping container a nd check for shipping damage. Report any damage immediately to your distributor an d shipping agent. Do not discard any shipping material until the band saw is assembled and running p roperly. Compare the contents of your container with the following parts list to make sure all parts are intact.
9 Assembly The Band Saw should be disconnected from po w er during assembly. When transporting the PB-85 band saw, it can be lifted by the bow when the cutting arm is locked in the down position. See Figure 1. Make sure the bow has been lowered all th e way and the pin has been pushed in to secure the bow before transporting.
10 Grounding Instructions This machine must be properly grounded while in use to protect the operator from electric sh ock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to redu ce the risk of electri c shock.
11 The green colored rigid ear, lug or tab, extending from the adapt er mu st be connected to a permanent ground such as a pro perly grounded outlet box, as shown in Fig ure 5. Extension cords If an extension cord i s necessary, make sure the cord rating is suitable for the ampe rage listed on the machine’s m otor plate.
12 Miter Cuts The band saw’s bow can be swiveled f or miter cuts (up to 45° on the Model PB-85; up to 60° on the Model PB-150). Loosen the handle (A, Figure 9) and pivot the bow to the desired angle on the scale (B, Figure 9). Adjustable stops (C, Figure 9 ) for square and 45° enable a quick setup.
13 Blade Replacement 1. Disconnect machine from powe r source. 2. Raise the bow to vertical position. 3. Loosen the handle (A, Figure 10) and l ower the blade guide and front cover (Figure 12) as far as possible. 4. Remove the back bl ade cover by unscrewing the knobs.
14 Operation The PB-85 and PB-150 Band Saws have been designed fo r dry cutting of metals only. Also, do not cut magne sium as this may present a fire h azard. Support long workpieces with roller stands. The start/stop switch contains a safety feature.
15 5. Rotate the speed dial to the desired setting. (The dial can also be rotated while the blade is running.) Refer to the cha rt in Figure 17 for recommende d blade speed and downfeed rate settings. 6. Press the blade run button on the hand grip to start the saw blade.
16 Troubleshooting Trouble Probable Cause Remedy No incoming power. Check plug connection. Blown electrical panel fuses. Replace fuses. Thermal overload has tripp ed. Release run button and wait several minutes for overload to reset itself. Motor will not start, or stops sudde nly.
17 Replacement Parts Replacement parts are listed on the following page s. To order parts or reach our se rvice department, call 1-800-274-6848 between 7:30 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine availabl e when you cal l will allow us to serve you quickly and accurately.
18 Model PB-85 Bow Assembl y (see parts list on page s 20-21).
19 Model PB-85 Base Assembly (see parts list on page s 20-21).
20 Parts List: Model PB-85 Index No. Part No. Description Size Qty 1 ............... PB85-001 ................. Body Frame.......................................................... .................. .................. 1 2 ............... TS-1540041 .
21 67 ............. PB85-067 ................. Gear-C ................................................................. ................ .................... 1 68 ............. BB-6202LLU ............ Bearing ..........................................
22 Model PB-150 Bow Assembly (see parts list on page s 24-26).
23 Model PB-150 Base Assembly (see parts list on page s 24-26).
24 Parts List: Model PB-150 Index No. Part No. Description Size Qty 1 ............... PB150-001 ............... Body Frame.......................................................... ................... ................. 1 2 ............... TS-1540041 .
25 46-11 ........ PB150-046-11 .......... G ear Box Cover ................................................... ........................... ......... 1 47 ............. PB150-047 ............... Phillips Pan Head Machine Screw ....................... M5 x 5L .
26 124 ........... TS-2284202 ............. Phillips Pan Head Machine Screw ....................... 4 x 20L ........................ 2 126 ........... PB150-126 ............... Switch Assembly .................................................. .......
27 Electrical Connections: Model PB-85.
28 Electrical Connections: Model PB-150.
An important point after buying a device Jet PB-150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jet PB-150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jet PB-150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jet PB-150 you will learn all the available features of the product, as well as information on its operation. The information that you get Jet PB-150 will certainly help you make a decision on the purchase.
If you already are a holder of Jet PB-150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jet PB-150.
However, one of the most important roles played by the user manual is to help in solving problems with Jet PB-150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jet PB-150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
