Instruction/ maintenance manual of the product XA4300 Jensen
Go to page of 15
® Amplifier Installation and Operation Installation Assistance M – F 8:00 am to 6:00 pm EST @ 1.800.323.0221 365 / 24 / 7 @ www .jensenaudio .com Introduction Thank you f or purchasing a Jensen amplifier . The XA series amplifiers off er e xtreme value and perf or mance.
2 XA4200, XA4300 ® Contents Features ......................................... 3 Installation ..................................... 3 Before Y ou Begin ......................................... 3 Disconnect Battery ...................................
® XA4200, XA4300 3 Installation Disconnect Battery Before you begin, always disconnect the battery negative terminal. Befor e Y ou Begin Before you begin, you will need tools, supplies and adapters. It is best to make sure you have everything you need before you start.
4 XA4200, XA4300 ® Routing Wires Location and Mounting Th e XA amplifier ’ s compact design allows greater flexibility in mounting. It can be mounted under a seat or in the trunk. When selecting a location, remember that amplifiers generate heat. Select a location where air can circulate around the amplifier .
® XA4200, XA4300 5 Wiring Power Remote T erminal (REM) P ower T erminal (+12V) Connect directly to the vehicle battery+ terminal with 8 gauge wire (minimum). Gr ound T erminal (GND) Connect to a good chassis ground. The ground connection should be to clean, unpainted metal to provide a good electrical connection.
6 XA4200, XA4300 ® Inputs, RCA Output, Remote Level Contr ol Input Wiring Low Level Input (RCA Input) Low level (RCA) input is preferred for best performance. Most trunk/hatchback installations will require a 15-20 foot RCA cable. While pick- up trucks and under-seat mounting will require a 6-10 foot RCA cable.
® XA4200, XA4300 7 Remote Level Contr ol – Rear Speaker s (XA4300) Remote level control allows the input level to be adjusted for the rear speakers from an alternate location.
8 XA4200, XA4300 ® 2 Subwoofers/Bridged Mono (XA4200) 4 Speakers Speaker Wiring Options 2 Speakers + Bridged Subwoofer X-OVER LPF HPF FULL X-OVER LPF HPF FULL FRONT REAR 2 Ω minimum 2 Ω minimum R.
® XA4200, XA4300 9 4 Speakers + 2 Subwoofers Important When running a subwoof er and two full-range speak ers together (T ri- mode operation), high and lo w pass filters must be used. F ailure to install these filters ma y damage y our amp and/or speakers .
10 XA4200, XA4300 ® Adjust the crossover to accommodate your chosen installation method. • LPF – (low pass filter) Select this filter when the amplifier will be driving woofers or subwoofers. • FULL – Crossover is not active, amplifier is in “ full range ” mode.
® XA4200, XA4300 11 When the input selector is set to 4 CH , the amplifier will operate as a standard 4 channel amp with all RCA inputs connected. 4 Channel 2CH 4CH 3CH LR RR INPUT OUTPUT LF RF REAR HI-LEVEL FRONT HI-LEVEL INPUT OUTPUT When the input selector is set to 3 CH , the amplifier is configured f or stereo/mono operation.
12 XA4200, XA4300 ® T est P o wer Wiring 1. T ur n on the receiver b ut do not tur n up the volume . The amplifier power light should come on. If not, check the REM and +12V wires. 2. T ur n up the receiver v olume slightly . All speakers should operate.
® XA4200, XA4300 13 T r oubleshooting Problem Possible Cause Corrective Action Amplifier does not operate (power LED not on) when vehicle and radio are on Radio volume needs to be turned up too high .
14 XA4200, XA4300 ® Specifications XA Series 4-Channel Amplifiers F requency Response ....................................................................................... 20 Hz-20 kHz ± 0.5 dB Signal to Noise Ratio @ Rated P ower ................
® XA4200, XA4300 15 ©2001 Recoton A udio Corporation Recoton Mobile Electronics A Division of Recoton Audio Corporation A RECO TON ® COMP ANY 1090 Emma Oaks T rail Lak e Mar y , Flor ida 32746 ® Limited One Y ear W arranty– USA and Canada Length of Warranty .
An important point after buying a device Jensen XA4300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jensen XA4300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jensen XA4300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jensen XA4300 you will learn all the available features of the product, as well as information on its operation. The information that you get Jensen XA4300 will certainly help you make a decision on the purchase.
If you already are a holder of Jensen XA4300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jensen XA4300.
However, one of the most important roles played by the user manual is to help in solving problems with Jensen XA4300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jensen XA4300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
