Instruction/ maintenance manual of the product 19200 Jasco
Go to page of 9
GE Model 19200 www.jascoproducts.com Wireless Portable Chime Installation Instructions for Wireless Portable Door Chime Kit Required Tools: Small flat blade screwdriver , drill, drill bit, and phillips screwdriver.
Battery Release Tab 2. Install 4 C-cell batteries (we recommend Alkaline Batteries) 3. Remove back of wireless push button and install the 12-volt battery (included) as shown below. Chime Tune Setting All wireless chimes may have more than one push button.
and 9=off.) 3. Select the desired chime sound from the table below. Chime Sound Table Position 7 8 9 Westminster ON OFF OFF Ding Dong OFF ON OFF Knock OFF OFF ON Bronze Chime ON ON OFF Cuckoo Clock ON OFF ON Foghorn OFF ON ON Gong ON ON ON ON: Add a jumper to a location OFF: Remove jumper from a location.
Each component has jumpers for setting the house security code: The chime and pushbutton must be set to the same house security code for the combination to operate together. Note : The push button has 3 additional jum pers that are used to set the chime tune that will play.
3. Locate the House Security Code door and screw located on the back of the AC Chime. Remove the screw and take off the door. 4. Locate the chime and pushbu tton jumpers shown below. Push Button Jumpers Chime Jumpers in battery compartment 5. Jumpers 1-6 are used to select 1 of 64 possible home security codes.
b. Replacing the back cover 1. Push buttons are typically mounted at the same height as the door knob or handle (between 36" and 44" above the floor). 2. Before mounting, choose a mounting location that is not farther than 150 feet from the chim e unit location.
Not farther than 150 feet 3. Place the push button where you w ould like to mount it and with the chime as close to its final position as possi ble and test operati on. If it works, mount the button. If it does not work, see TROUBLESHOOTING. 4. Use back cover of push button as a template to mark two screw holes.
7. Press front housin g onto back cover. 8. Test operation. If the chime does not work, see TROUBLESHOOTING. Operation 1. Slide power switch to “High” or “Low” to power the chime. 2. Gently press transmitter button to sound chime. Troubleshooting Chime doesn't work: 1.
For technical support contact Jasco Pr oducts Company at 1-800-654-8483 or www.jascoproducts.com Made in China is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 311 N.W. 122nd Street, Oklahoma City, OK 73114.
An important point after buying a device Jasco 19200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jasco 19200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jasco 19200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jasco 19200 you will learn all the available features of the product, as well as information on its operation. The information that you get Jasco 19200 will certainly help you make a decision on the purchase.
If you already are a holder of Jasco 19200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jasco 19200.
However, one of the most important roles played by the user manual is to help in solving problems with Jasco 19200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jasco 19200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
