Instruction/ maintenance manual of the product JP-24BF Jackson
Go to page of 59
TECHNICAL MANUAL INSTALLATION MANUAL FOR EXPORT UNITS SERVICE MANUAL FOR DOMESTIC UNITS FOR JACKSON MODELS: JP-24 JP-24F JP-24B JP-24BF An Company HOT WATER SANITIZING UNDERCOUNTER DISHMACHINES March 6, 2006 P/N 7610-002-49-79 (Revision D) Jackson MSC, Inc.
.
i REVISION REVISION DATE MADE BY APPLICABLE ECN DETAILS A 07-15-2002 MAW 6527 Release manual for service use. B 06-04-2003 MAW 6673, 6681 6637 Updated per ecns. C 02-11-2004 MAW 6836 Updated per ecns. D 03-06-2006 MAW 7421, 7231 6964, 7095 Change thermostat from 05930-121-71-29 to 05930-510-03-79.
ii NOMENCLATURE FOR THE MODELS COVERED IN THIS MANUAL JP-24B JP-24 = Undercounter, high temperature, hot water sanitizing, no booster tank. JP-24F = Undercounter, high temperature, hot water sanitizing, no booster tank, with top and side panels. JP-24B = Undercounter, high temperature, hot water sanitizing, with a booster tank.
SECTION DESCRIPTION PAGE I. SPECIFICATION INFORMATION Specifications JP-24/JP-24F 2 Specifications JP-24B/JP-24BF 3 Dimensions 4 II. INSTALLATION/OPERATION INSTRUCTIONS Installation Instructions 6 Electrical Installation Instructions 7 Operation Instructions 8 Detergent Control 9 Cycle Counter Retrofit Kit Instructions 10 III .
1 SECTION 1: SPECIFICATION INFORMATION.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 1: SPECIFICATION INFORMATION SPECIFICATIONS of the JP-24/JP-24F 2 PERFORMANCE/CAPABILITIES OPERATING CAPACITY (RACK.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 1: SPECIFICATION INFORMATION SPECIFICATIONS of the JP-24B/JP-24BF 3 PERFORMANCE/CAPABILITIES OPERATING CAPACITY (RA.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 1: SPECIFICATION INFORMATION JP-24 DIMENSIONS 4 LEGEND A - Water Inlet 1/2” ID Female Pipe Thread, 2 1/2” AFF B.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS 5.
VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indi - cator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container.
ELECTRICAL POWER CONNECTION: Electrical and grounding connections must comply with the applicable portions of the National Electrical Code ANSI/NFPA 70 (latest edition) and/or other electrical codes. Disconnect electrical power supply and place a tag at the disconnect switch to indicate that you are working on the circuit.
PREPARATION: Before proceeding with the start-up of the unit, verify the following: 1. The strainer is in place and is clean. 2. That the wash and rinse arms are screwed securely into place and that their endcaps are tight. The wash and rinse arms should rotate freely.
Detergent usage and water hardness are two factors that contribute greatly to how efficiently your dishmachine will operate. Using detergent in the proper amount can become, in time, a source of substantial savings.
1. Locate the template on the front of the plastic control panel in the approximate location as shown in the diagram below. 2. Use a 3/32" diameter drill bit to drill the four mounting holes through the plastic control panel. 3. Mount the template to the front of the control panel using the screws and locknuts provided.
SECTION 3: PREVENTATIVE MAINTENANCE 11.
The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator. However, this does not mean that some items will not wear out in time. Jackson highly recommends that any maintenance and repairs not specifically discussed in this manual should be performed by QUALIFIED SERVICE PERSONNEL ONLY.
SECTION 4: TROUBLESHOOTING 13.
WARNING: Inspection, testing and repair of electrical equipment should be performed only by qualified service personnel. Certain procedures in this section require electrical tests or measurements while power is applied to the machine. Exercise extreme caution at all times.
WARNING: Inspection, testing and repair of electrical equipment should be performed only by qualified service personnel. Certain procedures in this section require electrical tests or measurements while power is applied to the machine. Exercise extreme caution at all times.
16 SECTION 5: SERVICE PROCEDURES.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT 17 These dishmachines are equipped with electrical solenoid valves to allow for automatic fill and rinse.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT (CONTINUED) 18 4. When replacing the coil, ensure that when removing the coil wire cover that care is taken not to damage the wires inside.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT (CONTINUED) 19 13. Slowly remove the valve bonnet. Note: The spring for the plunger is located directly under the bonnet and may come free if you are not careful.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT (CONTINUED) 20 19. Using the small flathead screwdriver, lift out the screen retainer. Verify that the holes in it are free of clogs and debris.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES VACUUM BREAKER REPAIR PARTS KIT 21 These dishmachines are equipped with vacuum breakers to serve as back-flow prevention devices. ASSE requirements specify what type of back-flow prevention is nec - essary on dishmachines.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES VACUUM BREAKER REPAIR PARTS KIT (CONTINUED) 22 6. Your repair kit comes with a new plunger. Examine the old one and ensure that the mating surface is not damaged or cut.
REPLACING THE PUMP MOTOR The following list of tools will be needed to complete this procedure. 5/6” nutdriver, phillips screwdriver, 7/16” socket and ratchet, and 7/16” wrench. 1. Disconnect the electrical power to the dishwasher at the main circuit breaker box when servicing.
REPLACING THE DRAIN VALVE The following list of tools will be needed to complete this procedure. 5/16” nutdriver, flat screwdriver, phillips screwdriver, and 7/16” socket and ratchet. 1. Disconnect the electrical power to the dishwasher at the main circuit breaker box when servicing.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE REGULATING THERMOSTAT REPLACEMENT 25 Many dishmachines comes with integral booster tanks to ensure proper temperature of the final rinse. Jackson has predominantly used two manufacturers of thermostats, EGO and Stemco.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE REGULATING THERMOSTAT REPLACEMENT 26 Remove the thermostat bracket mounting nuts with the 3/8” nutdriver. 5. Attach the jumper wires to the wires that you removed from the old thermostat.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE REGULATING THERMOSTAT REPLACEMENT 27 6. Slide the new imperial brass fitting from your kit onto the new thermostat. 7. Insert the new thermostat/brass fitting combination into the well and tighten down the brass fitting by hand.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 5: SERVICE PROCEDURES RINSE REGULATING THERMOSTAT REPLACEMENT 28 11. Attach the ring ends of the jumpers to the cups/screws removed from the thermostat and attach them.
SECTION 6: PARTS SECTION 29.
ITEM QTY DESCRIPTION Mfg. No. 11 Gauge, 0-100 PSI w/Green Zone 06680-011-86-42 21 Fitting, 1/4” BARB x 1/4” FNPT Swivel 04730-011-95-42 31 Hose, 5/16” x 12" 05700-011-86-45 41 Fitting, 1/4.
ITEM QTY DESCRIPTION Mfg. No. 11 Electrical Control Panel Weldment 05700-011-41-79 21 Bushing, Snap 05975-210-03-00 31 Contactor, Motor 05945-002-74-20 48 Screw, 10-32 x 3/8” Phillips Truss Round He.
ITEM QTY DESCRIPTION Mfg. No. 11 Electrical Control Panel Weldment 05700-011-41-79 21 Bushing, Snap 05975-210-03-00 31 Contactor, Motor 05945-002-74-20 49 Screw, 10-32 x 3/8” Phillips Truss Round He.
ITEM QTY DESCRIPTION Mfg. No. 11 Bushing, Snap 05975-210-03-00 21 Track, Terminal 6 7/8" 05700-021-62-91 32 End Clamp 05940-111-60-30 42 Contactor, Mini 05945-111-60-07 59 Screw, 10-32 x 3/8” P.
ITEM QTY DESCRIPTION Mfg. No. 11 Gauge, 0-100 PSI with Green Zone 06680-011-86-42 21 Thermometer, 96” Wash 06685-111-68-49 31 Thermometer, 48” Rinse 06685-111-68-48 41 Control Panel, Remote JP-24 .
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION ELECTRICAL PANEL ASSEMBLY (EXTERNAL OPTION & AMTRAK OPTION) 35 13 12, 7 FRONT VIEW EXTERNAL OP.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION ELECTRICAL PANEL ASSEMBLY (EXTERNAL OPTION & AMTRAK OPTION) (CONTINUED) 36 ITEM QTY DESCRIPTION Mfg.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION KICK PLATE ASSEMBLY 37 Kickplate Weldment 05700-041-86-40 Control Panel Assembly 05700-011-40-93 C.
ITEM QTY DESCRIPTION Mfg. No. 11 Y-Strainer, 1/2" 04730-217-01-10 23 Adapter, 1/2" Ftg. x Male 04730-011-59-53 31 Tee, 1/2” C x 1/2” C x 1/4” Female 04730-411-25-01 41 Ball Valve, Test.
ITEM QTY DESCRIPTION Mfg. No. 11 Y-Strainer, 1/2" 04730-217-01-10 23 Adapter, 1/2" Ftg. x Male 04730-011-59-53 31 Tee, 1/2 x 1/2 x 1/4 04730-411-25-01 41 Ball Valve, Test Cock 1/4" 04810-011-72-67 51 Valve, Solenoid 1/2" 220 volt 04810-100-09-18 61 Union, 1/2" C to C 04730-412-05-01 72 Elbow, 1/2" C to Ftg.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION RINSE STIFFENER/RINSE HUB WELDMENT 40 Rinse Hub Weldment 05700-021-38-31 Rinse Tube Stiffener 0570.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A 41 SECTION 6: PARTS SECTION RINSE SOLENOID VALVE & VACUUM BREAKER REPAIR PARTS KITS/WATER PRESSURE REGULATOR KIT OPTION.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION DRAIN VALVE ASSEMBLY 42 3 1 3 4 5 6 12 7 8 9 10 11 18 13 14 15 16 17 ITEM QTY DESCRIPTION Mfg.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION DRAIN PLUMBING ASSEMBLY 43 ITEM QTY DESCRIPTION Mfg.
ITEM QTY DESCRIPTION Mfg. No. 1 1 Motor, Wash, 115/230 V, 60 HZ, Complete 06105-131-50-93 Motor, Only 06105-021-44-03 1 1 Motor, Wash, 115/230 V, 50 HZ, Complete 06105-002-14-93 Motor, Only 06105-003-.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A 45 SECTION 6: PARTS SECTION RINSE TANK & COMPONENTS/STRIP HEATER KIT 40 °F Rise 70 °F Rise Model Volts Hz Phase Rinse Heater (8.
ITEM QTY DESCRIPTION Mfg. No. 11 Door Handle, S/S 05340-011-60-25 21 Seal Channel, Inner Door, Left 05700-031-32-89 31 Kit, Outer Door with Tricnuts 06401-003-19-59 41 Right Hinge Assembly Weldment 05.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION MISCELLANEOUS DOOR SUB-ASSEMBLIES 47 Door Spring 05340-011-44-58 Hinge Retaining Plate 05700-011-4.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION RINSE ARM & WASH ARM ASSEMBLIES 48 Washer, Rinse Arm 05330-011-42-10 O-ring (Not Shown) 05330-.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION FRAME & PANEL COMPONENTS/MISCELLANEOUS PARTS 49 Back Panel 05700-031-44-33 Guide, Left Rack 05.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 6: PARTS SECTION CYCLE COUNTER RETROFIT KIT 50 Instructions for Adding Cycle Counter to JP - 24 Undercounter Dish Machi ne 1. Locate the template on the front of the plastic control panel in the approximate location as shown in the diagram below.
51 SECTION 7: ELECTRICAL SCHEMATICS.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 7: ELECTRICAL SCHEMATICS JP-24/JP-24F 208-230 VOLT - 50/60 HERTZ - SINGLE PHASE 52.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 7: ELECTRICAL SCHEMATICS JP-24B/JP-24BF 208-230 VOLT - 50/60 HERTZ - SINGLE PHASE 53.
JP-24 Technical Manual 7610-002-49-79 Rev. D Issued: 03-06-2006 Revised: N/A SECTION 7: ELECTRICAL SCHEMATICS JP-24B/JP-24BF 460 VOLT - 60 HERTZ - THREE PHASE 54.
An important point after buying a device Jackson JP-24BF (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jackson JP-24BF yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jackson JP-24BF - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jackson JP-24BF you will learn all the available features of the product, as well as information on its operation. The information that you get Jackson JP-24BF will certainly help you make a decision on the purchase.
If you already are a holder of Jackson JP-24BF, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jackson JP-24BF.
However, one of the most important roles played by the user manual is to help in solving problems with Jackson JP-24BF. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jackson JP-24BF along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center