Instruction/ maintenance manual of the product 4409706 iRobot
Go to page of 16
Mirra global.ir obot.com Pool Cleaning Robot Model 530 Owner’ s Manual.
2 iRobot Mirra 500 Series Owner’ s Manual IMPORT ANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL THE INSTRUCTIONS CAUTION: Do not plug the power supply into a grounded outlet or do not switch the pool cleaner “ON” if it is not fully immersed in water .
global.irobot.com 3 1) Handle 2) Cable 3) Outlet T op 4) Filter Access 5) Filter Lock Lever 6) Wheels 7) Unit Body 8) Intake Valves 9) Rolling Brush Dear Mirra Owner , Thank you for choosing a new generation iRobot Mirra pool cleaning robot. Y ou’r e joining a very special community of people - 7.
4 iRobot Mirra 500 Series Owner’ s Manual T able of Contents Getting Started ................................................................ 5 Maintenance and Adjustment ......................................... 6-7 Cleaning the Filter/ Changing the Rolling Brush .
global.irobot.com 5 1 2 4 3 56 7 Getting Started 12 cm (4.7 inch) 3.6m/11.8ft 15min. Soak wheels for 15 minutes.
6 iRobot Mirra 500 Series Owner’ s Manual Maintenance and Adjustment A B C D 15min. ST ART INT AKE V AL VES ADJUSTMENT Adjust filter valve to get best suction on ground. Adjust filter valve to get best clearance on ground. PV A WHEELS SOAKING Soak wheels after extended period of storage.
global.irobot.com 7 Maintenance and Adjustment Continued A1 A2 A3 A4 B2 B3 B1 B4 FLO A T INST ALLA TION Robot should turn 90 degrees on the first turn of a new cleaning cycle. Remove filter canister to access float block holder Adjust amount of float blocks to achieve desired turning behaviors.
8 iRobot Mirra 500 Series Owner’ s Manual Cleaning the Filter Changing the Rolling Brush It is recommended to clean the filter after each working-c ycle.
global.irobot.com 9 Accessing and Cleaning the Pr opeller DISCONNECT THE ROBO T FROM THE POWER-SUPPL Y BEFORE PERFORMING THIS ACTION 2 7 Propeller Clean here 6 1 5 10 9 4 3 8 Pump motor Clean the propeller if experiencing poor suction.
10 iRobot Mirra 500 Series Owner’ s Manual 4 1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and atleast 12 cm / 4 Inch above the surface. The transformer will supply low voltage to the cleaner . 2. Uncoil the cable.
global.irobot.com 11 Operating Y our Pool Cleaner - Plugging the Cable cable plug power supply socket cable plug power supply socket slot key slot key Push and rotate right to lock Rotate left and pull to unlock Cable plug (A) Socket (B) Plug T ype T o plug the cable (Fig A) into the socket on the power supply (Fig.
12 iRobot Mirra 500 Series Owner’ s Manual a. Power LED The blue LED flashes when the power supply is in standby mode and lights continuously when the pool cleaner is operating. b. “CLEAN” button The button switches between “ON” and “ST ANDBY”.
global.irobot.com 13 T roubleshooting Guide PLEASE CHECK THE FOLLOWING BEFORE CALLING YOUR SERVICE CENTER Before troubleshooting, the pool cleaner must be disconnected from the power supply and the power supply must be unplugged from the electrical outlet to prevent damage to the unit and possible personal injury.
14 iRobot Mirra 500 Series Owner’ s Manual Grounding The power supply must be connected to a grounded 3 conductor socket. The main power supply must be connected via a GFCI (ground fault circuit interrupter) or RCD (residual current device) having a rated residual opera ting current not greater than 30mA.
global.irobot.com 15 T roubleshooting Guide Declaration of Conformity T est Standards EN60335-1 Household and similar electrical appliances-Safety Part 1: General requirements EN60335-2-41 Household a.
© 2008-2014 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730 USA | All rights r eserved. iRobot is a registered trademark of iRobot Corporation. Mirra is a trademark of iRobot Corporation.
An important point after buying a device iRobot 4409706 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought iRobot 4409706 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data iRobot 4409706 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, iRobot 4409706 you will learn all the available features of the product, as well as information on its operation. The information that you get iRobot 4409706 will certainly help you make a decision on the purchase.
If you already are a holder of iRobot 4409706, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime iRobot 4409706.
However, one of the most important roles played by the user manual is to help in solving problems with iRobot 4409706. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device iRobot 4409706 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
