Instruction/ maintenance manual of the product 170 IPSO
Go to page of 18
Refer to Inst allation manual for full instr uctions. 4-08-45R4 June 201 1 On-Pr emise Laundr y Planning Handbook 120 and 170 P ound T umbler s T hr ough Serial No .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT © Published by pe rmission of the copyrig ht owner . All rights reserved. No part of the cont ents of this book may be reproduced or transmitted in any form or by any means without the expressed writte n consent of the publisher .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 2 4-08-45 T umbler s – 120 and 170 Introduction Model Identification Includes models with the follow ing control suffixes : T.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 3 TMB1298N 1 Serial Plate TMB1298N 120 POUND TUMBLER 1 1 170 POUND TUMBLER Conversion T able Multiply By T o Obt ain Multiply By T o Obt ain Btu 0.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 an d 170 4 4-08-45 S pecifications and Dimensions N/A = Not Applicable Specifica tions 120 Pound 170 Pound Noise level measured during operation at operator position of 3.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 5 120 Pound T umbler Dimensions and Exhaust Outlet Locations Refer to Position and Level the T umbler to temporarily reduce th e he ights of these models.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 an d 170 6 4-08-45 170 Pound T umbler Dimensions and Exhaust Outlet Locations Refer to Position and Level the T umbler to temporarily reduce the heights of these models.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 7 Electric and Gas Connection Locations for Gas Models NOTE: These figures ar e approximate dimensions only . TMB1301N A C C A B D B D 120L/N 170L/N Models Electrical Co nnection Gas Connection ABCD D i a m e t e r Non-CE 120L/N 27.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 an d 170 8 4-08-45 Electric and Steam C onnection Locations for Steam Models TMB1461N A1 B1 120S 170S A2 B2 D E F A1 B1 B2 A2 D E F C C Models Ste am I nl et Diameter A1 A2 F 120S 3/4 in.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 9 Inst allation Pre-Inst allation Inspection Upon delivery , visually insp ect the crate, carton and parts for any visible shipping damage.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 an d 170 10 4-08-45 T umbler Enclosure Figure 1 TMB2020N NOTE: Shaded areas indic ate adjacent structure. 1 0.5 in. (13 mm) re commended between machines for remo val or installation.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 11 Exhaust Requirement s Layout Whenever possible, install tumblers along an outside wall where duct length can be kept to a minimum, and make-up air can be easily accessed.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 an d 170 12 4-08-45 NOTE: Exhaust ducts must be constructed of sheet metal or other noncombustible material. Such ducts must be equivalent in str ength and corrosion resistance to ducts made of galvanized sheet steel not less than 0.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 13 Figure 2 NOTE: Do not install wire mesh or scr een in exhaust duct opening to avoid lint build-up or impacting proper discharge of air fr om tumblers.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 an d 170 14 4-08-45 Manifold V e nting While it is preferable to ex haust tumblers individually to the outdoors, a main collect or duct may be u sed if it is sized according to Figur e 4 and Figur e 5 .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 15 Figure 4 TMB2019N 1 NOTE: Where th e exhaust duct pierces a combustible wall or ce iling, the opening MUST be sized per local codes.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 an d 170 16 4-08-45 Figure 5 TMB2018N 1 NOTE: Where th e exhaust duct pierces a combustible wall or ce iling, the opening MUST be sized per local codes.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – 120 a nd 170 4-08-45 17 Electrical Requirement s Refer to T abl e 5 . NOTE: Minimum wire sizes ar e obtained from Canadian Electrical C ode and are in tended for use as a guideline only .
An important point after buying a device IPSO 170 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought IPSO 170 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data IPSO 170 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, IPSO 170 you will learn all the available features of the product, as well as information on its operation. The information that you get IPSO 170 will certainly help you make a decision on the purchase.
If you already are a holder of IPSO 170, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime IPSO 170.
However, one of the most important roles played by the user manual is to help in solving problems with IPSO 170. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device IPSO 170 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
