Instruction/ maintenance manual of the product T-270 Interfire Audio
Go to page of 20
MONO CHANNEL / 2 CHANNEL / 4 CHANNEL AUTOMOTIVE AMPLIFIER INSTRUCTION MANUAL T-1000M T-270 / T -2100 / T-2130 T-460 / T -480 By.
.
1 free installation. Congratulations on your Purchase • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' T echnology MOSFET PWM Power Supply . • Bridgeable & TRI-Mode Operation.
• NEVER operate the amplifier without the proper power and ground wire, 10 gauge minimum. • NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery . This fuse is to protect the car not the electronics.
INSTALLA TION 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting.
POWER CONNECTIONS CONNECTIONS INPUT CONNECTIONS It is important to have good quality power and ground connections. Remember , to complete an electrical circuit, the ground connection is just as important as the positive power connection.
5 FIG.2 MONO CHANNEL SYSTEM WIRING DIAGRAM AUTO - ANTENNA LEAD CH1 CH2 CAR STEREO HEAD UNIT B + GND REM LINE IN LINE OUT REMOCON GAIN BASS L.P.F PHASE 6V 0.
6 2 CHANNEL SYSTEM WIRING DIAGRAM FIG.2 B + GND REM AUTO - ANTENNA LEAD CH1 CH2 CAR STEREO HEAD UNIT LINE IN LINE OUT REMOCON L.P.F L.P.F H.P.F H.P.F 6V 0.
7 FIG.2 B + GND REM 4 CHANNEL SYSTEM WIRING DIAGRAM CH3 CH4 CH2 CH1 AUTO - ANTENNA LEAD CAR STEREO HEAD UNIT LINE IN LINE IN GAIN GAIN BASS BASS CROSSOVER CROSSOVER 6V 0.2V 0dB 12dB 50Hz 500Hz CH1 CH2 CH3 CH4 50Hz 500Hz 0dB 12dB 6V 0.2V CH 1/2 CH 3/4 FLAT L.
ON PROTECT POWER B + GND REM FUSE SPEAKER This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4 or 8 ohms. Tri channel power is referred to stereo and mono at the same time.
ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER 2 CH SPEAKER WIRING DIAGRAM 2 - 4 Ohm 1 CH 2 CH 1 SPEAKER BRIDG ED 2 SPEAKER STER EO 3 SPEAKER TRI MODE 4 - 8 Ohm 1CH ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER FIG.
4 CH SPEAKER WIRING DIAGRAM 2 S PEAKER BRIDGED 2 S PEAKER + 1 SUBWOOFER 4 S PEAKER STEREO 6 S PEAKER HEX MODE 10 SPEAKER CONNECTIONS SPEAKER BRIDGED CH1 CH3 CH2 CH4 ON PROTECT POWER B + GND REM FUSE S.
11 ADJUSTMENTS 1.Set to the "H.P .F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency 2.
FRONT/REAR P ANEL 12 2CHANNEL ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER 30A TUNN T-270 By LINE IN LINE OUT L.P.F L.P.F H.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz FLAT 80Hz 1.2KHz CROSSOVER CH1 CH2 CH1 CH2 BASS GAIN ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER 25A 25A T-2100 By TUNN LINE IN LINE OUT REMOCON L.
FRONT/REAR P ANEL 13 4CHANNEL MONO CHANNEL LINE IN LINE IN GAIN GAIN BASS BASS CROSSOVER CROSSOVER 6V 0.2V 0dB 12dB 50Hz 500Hz CH1 CH2 CH3 CH4 50Hz 500Hz 0dB 12dB 6V 0.
14 This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e.
NOTE : Specifications & design subject to change without notice for improvements. SPECIFICATI ON SPECIFICATI ON 100W x 2 160W x 2 50Hz-250Hz 900 Watts YES >100 <0.1% HP/FULL/LP 270 15 T-2 70 Output Power Rating RMS Channel Total Max Power 4 Ohm at 14.
NOTE : Specifications & design subject to change without notice for improvements. SPECIFICATI ON SPECIFICATI ON 330W x 1 510W x 1 50Hz-250Hz 1200 Watts YES >150 <0.1% N / A 330 N / A 16 T-1 000M Output Power Rating RMS Channel Total Max Power 4 Ohm at 14.
Please call TUNN Customer Service at 1- 877-90-AUDIO to obtain an RA # (Return Authorization number). All warranty returns applied to products. (TUNN will not be WARRANTY WARRANT Y LIMIT ATIONS The following is NOT covered under TUNN warranty program: NOTICE: Products shipped without a valid RA # will be refused and shipped back.
10110 Santa Fe Springs Road Santa Fe Springs, CA 90670 1-562-926-2600.
An important point after buying a device Interfire Audio T-270 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Interfire Audio T-270 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Interfire Audio T-270 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Interfire Audio T-270 you will learn all the available features of the product, as well as information on its operation. The information that you get Interfire Audio T-270 will certainly help you make a decision on the purchase.
If you already are a holder of Interfire Audio T-270, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Interfire Audio T-270.
However, one of the most important roles played by the user manual is to help in solving problems with Interfire Audio T-270. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Interfire Audio T-270 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
