Instruction/ maintenance manual of the product 253666-024US Intel
Go to page of 760
In tel® 64 and IA-32 Ar chitectur es So ftw ar e De v eloper’ s Manual Vo l u m e 2 A : Instruction Se t R e f er ence, A-M NO TE: The In tel 64 and IA-32 Architectu re s S of tw are D eve lo pe r .
ii Vol. 2A INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNE CTION WITH I NTEL PRODUCTS . NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPE L OR OTHERWISE, TO ANY INTELLECTUAL PROP ERTY RIGHTS IS GRANT- E D B Y T H I S D O C U M E N T .
Vol. 2A iii CONT ENTS PAG E CHAP TER 1 ABOUT THIS MANUAL 1.1 IA-32 PROCES SORS COVERED IN THIS MAN UAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2 OVERVIEW OF VOLUME 2A AN D 2B: INSTRUCTION SET REFERENCE . . . . .
CONTE NTS iv Vol. 2A PAG E 3.1.1.5 Description Col umn in the Instruction Summary Ta ble . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 3.1.1.6 Description Secti on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vol. 2A v CONTE NTS PAG E CLFLUSH—Flu sh Cache Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 -108 CLI — Clear Int errupt Flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTE NTS vi Vol. 2A PAG E Double-Precision F loating-Point Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-231 CVTSS2SI—Convert Sca lar Single-Precision Floatin g-Point Value to Doubleword Integ er . . . . . . . . . .
Vol. 2A vii CONTE NTS PAG E FLD—Load Floa ting Point Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 41 FLD1/FLDL2T/FLDL2E/FLDPI/FLDLG2/FLDLN2/FLD Z— Load Constant . . . . . . . . . . . 3-344 FLDCW—Load x87 FPU Cont rol Word .
CONTE NTS viii Vol. 2A PAG E JMP—Jump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-508 LAHF—Load S tatus Flags into AH Regi ster . . . . . . . . . . . . .
Vol. 2A ix CONTE NTS PAG E MOVNTDQ—Store Do uble Quadword Using Non-Te mporal Hint . . . . . . . . . . . . . . . . . 3-649 MOVNTI—Store Do ubleword Using Non-Te mporal Hint . . . . . . . . . . . . . . . . . . . . . . . . . 3-652 MOVNTPD—Store Packed Dou ble-Precision Floating-Poin t Values Using Non-Temporal Hi nt .
CONTE NTS x Vol. 2A PAG E PAVGB/PAVGW— Average Packed Integers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61 PCMPEQB/PCMPEQW/PC MPEQD— Compare Packed Data for E qual . . . . . . . . . . . . . . . . 4-64 PCMPGTB/PCMPGTW/PCMPGTD—Compare Packed S igned Integers for Greater Than .
Vol. 2A xi CONTE NTS PAG E PUSH—Push Word, Dou bleword or Quadword Onto the Stack . . . . . . . . . . . . . . . . . . . 4-217 PUSHA/PUSHAD—Push All Gener al-Purpose Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 4-222 PUSHF/PUSHFD—Pus h EFLAGS Register on to the Stack .
CONTE NTS xii Vol. 2A PAG E SYSCALL—Fa st System Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-367 SYSENTER—Fast S ystem Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vol. 2A xiii CONTE NTS PAG E CHAPTER 6 SAFER MODE EXTENSIONS REF ERENCE 6.1 OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 6.2 SMX FUNCTI ONALITY .
CONTE NTS xiv Vol. 2A PAG E A.5.2.3 Escape Opcodes with DA as Fi rst Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-25 A.5.2.4 Escape Opcodes with DB as First B yte . . . . . . . . . . . . . . . . . . . . . . . . .
Vol. 2A xv CONTE NTS PAG E FIGUR ES Figure 1-1. Bit and Byte Or der . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Figure 1-2. Syntax for CPUID, CR , and MSR Data Presenta tion.
CONTE NTS xvi Vol. 2A PAG E TABLES Table 2-1. 16-Bit Addressing Fo rms with the ModR/M Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Table 2-2. 32-Bit Addressing Fo rms with the ModR/M Byte . . . . . . . . . . . . . . . . . . .
Vol. 2A xvii CONTE NTS PAG E Table 3-38. FP TAN Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-365 Table 3-39. FS CALE Results . . . . . . . . . . . . . . . . . . . . .
CONTE NTS xviii Vol. 2A PAG E Table A-1. Superscripts Utilized in Op code Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7 Table A-2. One-byte Opcode Map: (00H — F7H) *. . . . . . . . . . . . . . . . . . . .
Vol. 2A xix CONTE NTS PAG E Table B-23. Format and Enco ding of SSE Cacheability & Memory Ordering Instruc tions . . . . . . B-67 Table B-24. Enco ding of Granularity of D ata Field (gg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTE NTS xx Vol. 2A PAG E.
Vol. 2A 1-1 CHAP TER 1 ABOUT THIS MANUAL The Intel ® 64 and IA-32 Architectures Software Developer’s Manual, Volumes 2A & 2B : Instruction Set Reference (order numbers 253666 and 253667 ) are part of a set that describes the architecture and programming environment of all Intel 64 and IA-32 architecture processors.
1-2 Vol. 2A ABOUT THIS M ANUAL • Intel ® Core™2 Duo processor • Intel ® C o r e™ 2 Q u a d p r oc e s s o r • Intel ® Xe on ® processor 3000, 3200 series • Intel ® Xe on ® processor .
Vol. 2A 1-3 ABOUT THIS MANUAL Chapter 1 — About This Manual. Gives an overview of all five volumes of the Intel ® 64 and IA-32 Architectures Software Developer’ s Manual . It also describes the notational conventions in these manuals and lists related Intel ® manuals and docu- mentation of interest to programmers and hardware designers.
1-4 Vol. 2A ABOUT THIS M ANUAL 1.3.1 Bit and Byte Order In illustrations of data structures in memory , smaller addresses appear toward the bottom of the figure; addresses increase tow ard the top. Bit positions are numbered from right to left. The numerical v alue of a set bit is equal to two raised to the power of the bit position.
Vol. 2A 1-5 ABOUT THIS MANUAL 1.3.2 R eserved Bits and Softw a r e Compatibility In many register and memory layout descriptions, certain bits are marked as reserved . When bits are marked as reserved, it is essential for compatibility with future processors that software treat these bits as having a future, though unknown, effect.
1-6 Vol. 2A ABOUT THIS M ANUAL 1.3.3 Instruction Oper ands When instructions are represented symbol ically , a subset of the IA -32 assembly language is used. In this subset, an instruction has the following format: label: mnemo nic argument1, argument2, arg ument3 where: • A label is an identifier which is followed by a colon.
Vol. 2A 1-7 ABOUT THIS MANUAL For example, a progr am can keep its code (instructions) and stack in separate segments. Code addresses would always refer to the code space, and stack addresses would always refer to the stack space.
1-8 Vol. 2A ABOUT THIS M ANUAL 1.4 R ELATED LITER ATURE Literature related to Intel 64 and IA -32 processors is listed on-line at: http://developer .intel.com/products/processor/manuals/index.htm Some of the documents listed at this web site can be viewed on-line; others can be ordered.
Vol. 2A 1-9 ABOUT THIS MANUAL literature types: applications notes, data sheets, manuals, papers, and specification updates. See also: • The data sheet for a particular Intel 64 or IA -32 processor • The specification update for a particular Intel 64 or IA-32 processor • Intel ® C++ Compiler documentation and online help http://www .
1-10 Vol. 2A ABOUT THIS M ANUAL • Intel 64 and IA-32 processor manuals (printed or PDF downloads): http://developer .intel.com/products/processor/manuals/index.h tm • Intel ® Multi-Core T echnology: http://developer .intel.com/multi-core/index.htm • Hyper- Threading T echnology (HT T echnolog y): http://developer .
Vol. 2A 2-1 CHAP TER 2 INSTRUCTION F ORMAT This chapter describes the instruction format for all Intel 64 and IA -32 processors. The instruction format for protected mode, real- address mode and virtual-8086 mode is described in Section 2.1. Increm ents provided for IA -32e mode and its sub- modes are described in Section 2.
2-2 Vol. 2A INSTRUCTION F ORMAT • F2H—REPNE/REPNZ (used only with string instructions; when u sed with the escape opcode 0FH, this prefix is treated as a mandatory prefix for some SIMD instruction.
Vol. 2A 2-3 INSTRUCTION F ORMAT opcodes with Intel 64 or IA-32 instructions is reserved; such use may cause unpre- dictable behavior . The operand-size override prefix allows a progr am to switch between 16- and 32-bit operand sizes. Either size can be the default; use of th e prefix selects the non-default size.
2-4 Vol. 2A INSTRUCTION F ORMAT 2.1.3 ModR/M and SIB Bytes Many instructions that refer to an oper and in memory have an addressing-form spec- ifier byte (called the ModR/M byte) followi ng the primary opcode.
Vol. 2A 2-5 INSTRUCTION F ORMAT location; the last eight (Mod = 11B) prov ide ways of specifying gener al-purpose, MMX technology and XMM registers. The Mod and R/M columns in T able 2-1 and T a ble 2-2 give the binary encodings of the Mod and R/M fields required to obtain the effective address listed in the first column.
2-6 Vol. 2A INSTRUCTION F ORMAT NO TES: 1. The default segm ent regi ster is SS f or the eff ective addr esses c ontaining a BP index, DS f or other eff ective addr esses. 2. The disp16 nomenclature denotes a 16-bit displace ment that f ollows the ModR/M byte and that is added t o the index.
Vol. 2A 2-7 INSTRUCTION F ORMAT NOT ES: 1. The [--][--] nomenclature mean s a SIB follo ws the ModR/M byte. 2. Th e disp32 nomenclature denotes a 32-bit di spla cement tha t follo ws the ModR/M byte (or the SIB byte if one is presen t) and that is added t o the index.
2-8 Vol. 2A INSTRUCTION F ORMAT of the table indicate the register used as th e index (SIB byte bits 3, 4 and 5) and the scaling factor (determined by SI B byte bits 6 and 7). NO TES: 1. The [*] nomenclature means a disp 32 with no base if the MOD is 00B.
Vol. 2A 2-9 INSTRUCTION F ORMAT 2.2 IA-32E MODE IA-32e mode has two sub-modes. These are: • Compatibility Mode. Enables a 64-bit operating sy stem to run most legacy protected mode software unmodified. • 64-Bit Mode. Enables a 64-bit operating system to run applications written to access 64-bit address space.
2-10 Vol. 2A INSTRUCTION F ORMAT 2.2.1.1 Encoding Intel 64 and IA-32 instruction formats specify up to three registers by using 3-bit fields in the encodin g, depending on the format: • ModR/M: the .
Vol. 2A 2-11 INSTRUCTION F ORMAT T able 2-4. REX Pre fix Fields [BITS: 0100WRXB] Field Name Bit Position Definition - 7:4 0100 W 3 0 = Operand size de termin ed by CS.
2-12 Vol. 2A INSTRUCTION F ORMAT In the IA-32 architecture, byte registers (AH, A L, BH, BL, CH, CL, DH, and DL) are encoded in the ModR/M byte’s reg field, the r/m field or the opcode reg field as regis- ters 0 through 7.
Vol. 2A 2-13 INSTRUCTION F ORMAT 2.2.1.3 Displacemen t Addressing in 64-bit mod e uses existing 32-bit ModR/M and SIB encodings. The ModR/M and SIB displacement sizes do not change. They remain 8 bits or 32 bits and are sign-extended to 64 bits. 2.2.1.
2-14 Vol. 2A INSTRUCTION F ORMAT size of the memory offset follows the addre ss-size default (64 bits in 64-bit mode). See T able 2-6. 2.2.1.5 Immediates In 64-bit mode, the typical size of immedi ate operands remains 32 bits. When the operand size is 64 bits, the processor sign-extends all immediates to 64 bits prior to their use.
Vol. 2A 2-15 INSTRUCTION F ORMAT The ModR/M encoding for RIP-relative addressing does not depend on using prefix. Specifically , the r/m bit field encoding of 10 1B (used to select RIP-relative addressing) is not affected by the REX pref ix. For example, selecting R13 (REX.
2-16 Vol. 2A INSTRUCTION F ORMAT.
Vol. 2A 3-1 CHAP TER 3 INSTRUCTION SE T R EF ERENCE, A-M This chapter describes the instruction set for the Intel 64 and IA -32 architectures (A-M) in IA-32e, protected, Virtual-8086, and real modes of operation. The set includes general-purpose, x87 FPU, MMX, S SE/SSE2/SSE3/S SSE3, and system instructions.
3-2 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M 3.1.1.1 Opcode Column in the Ins truction Summary T able The “Opcode” column in the table abov e sh ows the object code produced for each form of the instruction. When possible, codes are given as hexadecimal bytes in the same order in which they appear in memory .
Vol. 2A 3-3 INSTRUCTION SE T REF ERENCE, A-M 3.1.1.2 Instruction Column in the Opc ode Summary T able The “Instruction” column gives the syntax of the instruction statement as it would appear in an ASM386 progr am.
3-4 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M • ptr16:16, ptr16:32 and ptr16:64 — A far pointer , typically to a code segment different from that of the instruction. The notation 16:16 indicates that the value of the pointer has two parts. The value to th e left of the colon is a 16-bit selector or value destined for the code segment register .
Vol. 2A 3-5 INSTRUCTION SE T REF ERENCE, A-M • r/m32 — A doubleword gener al-purpose register or memory operand used for instructions whose operand-size attribute is 32 bits. The doubleword general- purpose registers are: EAX, ECX, EDX, EBX, ESP , EBP , ESI, EDI.
3-6 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M • Sreg — A segment register . The segment register bit assignments are ES = 0, CS = 1, SS = 2, DS = 3, FS = 4, and GS = 5. • m32fp, m64fp, m80fp — A single-precision, double-precision, and double extended-precision (respectively) floating-point operand in memory .
Vol. 2A 3-7 INSTRUCTION SE T REF ERENCE, A-M • N.P. — Indicates the REX prefix does not affect the legacy instruction in 64-bit mode. • N.I. — Indicates the opcode is treated as a new instruction in 64-bit mode. • N.S. — Indicates an instruction syntax that requires an address override prefix in 64-bit mode and is not supported.
3-8 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M address contained in register SI relative to the SI register’s default segment (DS) or the overridden segment.
Vol. 2A 3-9 INSTRUCTION SE T REF ERENCE, A-M Attribut e for Stack” in Chapter 6, “P rocedure Calls, Interrupts, an d Exceptions, ” of the Intel® 64 and IA-32 Architectures Soft ware Developer’s Manual, Volu me 1 . • SRC — R epresents the source operand.
3-10 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M zero (00H); if it is greater than 65535, it is represented by the saturated v alue 65535 (FFFFH). • LowOrderWord(DEST * SRC) — Multiplies a word operand by a word oper and and stores the least significant word of the doubleword result in the destination operand.
Vol. 2A 3-11 INSTRUCTION SE T REF ERENCE, A-M The addressed bit is numbere d (Offset MOD 8) within the byte at address (BitBase + (BitOffset DIV 8)) where DIV is sign ed division with rounding towards negative infinit y and MOD returns a positive number (se e Figure 3-2).
3-12 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M See Appendix C, “InteL® C/C++ Compiler In trinsics and Functional Equivalents, ” in the Intel® 64 and IA-3 2 Architectures Software Developer’s Manual, Volume 2B , for more information on using intrinsics.
Vol. 2A 3-13 INSTRUCTION SE T REF ERENCE, A-M • The __m128i data type can hold sixteen by te, eight word, or four doubleword, or two quadword integer v alues. The compiler aligns __m1 28, __m128d, and __m128i local a nd global data to 16-byte boundaries on the stack.
3-14 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M Some intrinsics are “composites” because th ey require more than one instruction to implement them. Y ou should be familiar with the hardware features provided by the SSE, SS E2, SSE3 , and M MX tech nology when writing programs with the intrinsics.
Vol. 2A 3-15 INSTRUCTION SE T REF ERENCE, A-M letter mnemonic with the correspon ding interrupt v ector number and exception name. See Chapter 5, “Interrupt and Ex ception Handling, ” in the Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 3A , for a detailed description of the exceptions.
3-16 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M 3.1.1.12 Real-Addr ess Mo de Exc eptions Section The “Real- Address Mode Exceptions” section lists the exceptions that can occur when the instruction is executed in real-address mode (see T able 3-3). 3.
Vol. 2A 3-17 INSTRUCTION SE T REF ERENCE, A-M 3.1.1.15 SIMD Floating-Poin t Exc eptions Section The “SIMD Floating-P oint Exceptions” section lists exceptions that can occur when an SSE/SSE2/S SE3 floating-point instruction is executed.
3-18 Vol. 2A INSTRUCTION SE T REF ERENCE, A-M 3.2 INSTRUCTIONS (A-M) The remainder of this chapter provides descr iptions of Intel 64 and IA-32 instructions (A-M). See also: Chapter 4, “Instruc tion Set R eference, N-Z, ” in the Intel® 64 and IA-32 Architectures Software Develope r’s Manual, Volume 2B .
Vol. 2A 3-19 INSTRUCTION SE T REF ERENCE, A-M AAA—ASCII Adjust After Addition AAA—ASCII Adjust A fter Addition Description Adjusts the sum of two unpacked BCD v alues to create an unpacked BCD result. The AL register is the implied source and destin ation operand for this instruction.
3-20 Vol. 2A AAA—ASCII Adjust After Addition INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #UD If the LOCK prefix is used. Real-Addr ess Mode Exc eptions Same exceptions as protected mode. Virtual-8086 Mode E xce ptions Same exceptions as protected mode.
Vol. 2A 3-21 INSTRUCTION SE T REF ERENCE, A-M AAD—ASCII Adjust AX Before Division AAD—ASCII Adjust AX Be for e Division Description Adjusts two unpacked BCD digits (the least-si gnificant digit in.
3-22 Vol. 2A AAD—ASCII Adjust AX Before Division INSTRUCTION SE T REF ERENCE, A-M Flags A ffected The SF , ZF , and PF flags are set according to the resulting binary value in the AL register; the OF , AF , and CF flags are undefined. Pro tected Mode Ex ceptions #UD If the LOCK prefix is used.
Vol. 2A 3-23 INSTRUCTION SE T REF ERENCE, A-M AAM—ASCII Adjust AX After Multiply AAM—ASCII Adjust AX A fter Mul tiply Description Adjusts the result of the multiplic ation of two unpacked BCD values to create a pair of unpacked (base 10) BCD values.
3-24 Vol. 2A AAM—ASCII Adjust AX After Multiply INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #DE If an immediate value of 0 is used. #UD If the LOCK prefix is used. Real-Addr ess Mode Exc eptions Same exceptions as protected mode. Virtual-8086 Mode E xce ptions Same exceptions as protected mode.
Vol. 2A 3-25 INSTRUCTION SE T REF ERENCE, A-M AAS—ASCII Adjust AL After Subtraction AAS—ASCII Adjust A L A fter Subtr action Description Adjusts the result of the subtraction of two unpacked BCD v alues to create a unpacked BCD result. The AL register is the implied source and destination operand for this instruction.
3-26 Vol. 2A AAS—ASCII Adjust AL After Subtraction INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #UD If the LOCK prefix is used. Real-Addr ess Mode Exc eptions Same exceptions as protected mode. Virtual-8086 Mode E xce ptions Same exceptions as protected mode.
Vol. 2A 3-27 INSTRUCTION SE T REF ERENCE, A-M ADC—Add with Carry ADC—Add with Carry Opcode Instruction 64-Bi t Mode Compat/ Leg M ode Description 14 ib ADC AL, imm8 V alid V alid Add with carry imm8 to AL. 15 iw ADC AX, imm16 Valid V alid Add with carry imm16 to AX.
3-28 Vol. 2A ADC—Add with Carry INSTRUCTION SE T REF ERENCE, A-M Descripti on Adds the destination operand (first operan d), the source operand (second oper and), and the carry (CF) flag and stores the result in the destination operand.
Vol. 2A 3-29 INSTRUCTION SE T REF ERENCE, A-M ADC—Add with Carry If the DS, ES, FS , or GS register is used to access memory and it contains a NULL segment selector . #SS(0) If a memory operand effective address is outside the SS segment limit. #PF(fault -code) If a page fault occurs.
3-30 Vol. 2A ADD—Add INSTRUCTION SE T REF ERENCE, A-M ADD—Add Opcode Instruction 64-Bit Mode Compat/ Leg Mode Description 04 ib ADD AL, imm8 Val i d Val i d A d d imm8 to AL. 05 iw ADD AX, imm16 Va li d Va l i d Ad d imm16 to A X. 05 id ADD EAX, imm32 Va li d Va l i d Ad d imm32 to E AX.
Vol. 2A 3-31 INSTRUCTION SE T REF ERENCE, A-M ADD—Add Description Adds the destination operand (first op erand) and the source oper and (second operand) and then stores the result in the destination operand.
3-32 Vol. 2A ADD—Add INSTRUCTION SE T REF ERENCE, A-M #SS If a memory operand effective address is outside the SS segment limit. #UD If the LOCK prefix is used but the destination is not a memory operand. Virtual-8086 Mode E xc eptions #GP(0) If a memory oper and effectiv e address is outsid e the CS, DS, ES, FS, or GS segment limit.
Vol. 2A 3-33 INSTRUCTION SE T REF ERENCE, A-M ADDPD—Add Packed Double-Precision Floating-Point Values ADDPD—Add Pack ed Double-Preci sion Floating-Point V alues Description Performs a SIMD add of .
3-34 Vol. 2A ADDPD—Add Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CRO .EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.01H:EDX.
Vol. 2A 3-35 INSTRUCTION SE T REF ERENCE, A-M ADDPD—Add Packed Double-Precision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .01H:EDX.
3-36 Vol. 2A ADDPS—Add Packed Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M ADDPS—Add Pa ck ed Single-Precision Floating-P oint V alues Descripti on Performs a SIMD add o.
Vol. 2A 3-37 INSTRUCTION SE T REF ERENCE, A-M ADDPS—Add Packed Single-Precision Floating-Point Values #XM If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0.
3-38 Vol. 2A ADDPS—Add Packed Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #XM If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0.
Vol. 2A 3-39 INSTRUCTION SE T REF ERENCE, A-M ADDSD—Add Scalar Double-Precision Floating-Point Values ADDSD—Add Scalar Double-Preci sion Floating-Poin t V alues Description Adds the low double-pre.
3-40 Vol. 2A ADDSD—Add Scalar Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .01H:E DX.
Vol. 2A 3-41 INSTRUCTION SE T REF ERENCE, A-M ADDSD—Add Scalar Double-Precision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .01H:EDX.
3-42 Vol. 2A ADDSS—Add Scalar Single-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M ADDSS—Add Scalar Single-Precision Floating-Point V alues Descripti on Adds the low single-pre.
Vol. 2A 3-43 INSTRUCTION SE T REF ERENCE, A-M ADDSS—Add Scalar Single-Pre cision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .01H:EDX.
3-44 Vol. 2A ADDSS—Add Scalar Single-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.01H:EDX.
Vol. 2A 3-45 INSTRUCTION SE T REF ERENCE, A-M ADDSUBPD—Packed Double-FP Add/Subtract ADDSUBPD—Pack ed Double-FP Add/Subtr act Description Adds the double-precision floating-point va lues in the high quadword of the source and destination operands and stores the resu lt in the high quadword of the destina- tion operand.
3-46 Vol. 2A ADDSUBPD—Packed Double-FP Add/Subtract INSTRUCTION SE T REF ERENCE, A-M Operat ion xmm1[63:0] = xmm1[63:0] − xmm2/m128[63:0]; xmm1[127:64] = xmm1[127 :64] + xmm2/m128[12 7:64]; Intel .
Vol. 2A 3-47 INSTRUCTION SE T REF ERENCE, A-M ADDSUBPD—Packed Double-FP Add/Subtract #UD If CR0.EM[bit 2] = 1. For an unmasked Streaming SIMD Extensions numeric excep- tion (CR4.OSXMMEXCPT[bit 10] = 0). If CR4.OSFXSR[bit 9] = 0. If CPUID. 01H:ECX.SSE3[bit 0] = 0.
3-48 Vol. 2A ADDSUBPD—Packed Double-FP Add/Subtract INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.01H:ECX.SSE3[bit 0] = 0.
Vol. 2A 3-49 INSTRUCTION SE T REF ERENCE, A-M ADDSUBPS—Packed Single-FP Add/S ubtract ADDSUBPS—Pack ed Single-FP Add/Subtra ct Description Adds odd-numbered single-precision floati ng-point values.
3-50 Vol. 2A ADDSUBPS—Packed Single-FP Add/Subtract INSTRUCTION SE T REF ERENCE, A-M Operat ion xmm1[31:0] = xmm1[31:0] − xmm2/m128[31:0]; xmm1[63:32] = xmm1[6 3:32] + xmm2/m12 8[63:32]; xmm1[95:6.
Vol. 2A 3-51 INSTRUCTION SE T REF ERENCE, A-M ADDSUBPS—Packed Single-FP Add/S ubtract #XM For an unmasked Streaming SIMD E xtensions numeric excep- tion, CR4.OSXMMEXCPT[bit 10] = 1. #UD If CR0.EM[bit 2] = 1. For an unmasked Streaming SIMD Extensions numeric excep- tion (CR4.
3-52 Vol. 2A ADDSUBPS—Packed Single-FP Add/Subtract INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.01H:ECX.SSE3[bit 0] = 0.
Vol. 2A 3-53 INSTRUCTION SE T REF ERENCE, A-M AND—Logical AND AND—Logical AND Opcode Instruction 64-Bit Mode Comp/Leg Mode Descript ion 24 ib AND AL, imm8 Val i d Va l i d AL A N D imm8. 25 iw AND AX, imm16 Va l i d Va l i d A X A N D i mm16. 25 id AND EAX, imm32 Va l i d Va l i d E A X A N D imm32.
3-54 Vol. 2A AND—Logical AND INSTRUCTION SE T REF ERENCE, A-M Descripti on Performs a bitwise AND operation on the destination (first) and source (second) operands and stores the result in the destination operand location.
Vol. 2A 3-55 INSTRUCTION SE T REF ERENCE, A-M AND—Logical AND #UD If the LOCK prefix is used b u t the destination is not a memory operand. Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit.
3-56 Vol. 2A ANDPD—Bitwise Logical AND of Packed Do uble-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M ANDPD—Bitwise Logical AND o f Pack ed Double-Precision Floating- Point V .
Vol. 2A 3-57 INSTRUCTION SE T REF ERENCE, A-M ANDPD—Bitwise Logical AND of Packed Do uble-Precision Floating-Point Values Real-Address Mode Ex ceptions #GP(0) If a memory operand is not aligned on a 16-byte boundary , regardless of segment. If any part of the operand lies outside the effective address space from 0 to FFFFH.
3-58 Vol. 2A ANDPS—Bitwise Logical AND of Packed Si ngle-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M ANDPS—Bitwise Logical AND o f Pack ed Single-Precision Floating-Poin t Va .
Vol. 2A 3-59 INSTRUCTION SE T REF ERENCE, A-M ANDPS—Bitwise Logical AND of Packed Si ngle -Precision Floating-Point Values Real-Address Mode Ex ceptions #GP(0) If a memory operand is not aligned on a 16-byte boundary , regardless of segment. If any part of the operand lies outside the effective address space from 0 to FFFFH.
3-60 Vol. 2A ANDNPD—Bitwise Logical AND NOT of Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M ANDNPD—Bitwise Logical AND NO T of Pack ed Double-Precision Floating-P.
Vol. 2A 3-61 INSTRUCTION SE T REF ERENCE, A-M ANDNPD—Bitwise Logical AND NOT of Packed Dou ble-Precision Floating-Point Values #UD If CR0.EM[bit 2] = 1.
3-62 Vol. 2A ANDNPS —Bitwise Logical AND NOT of Packed Single-Precision Floating-P oint Values INSTRUCTION SE T REF ERENCE, A-M ANDNPS—Bitwise Logical AND NO T of P ack ed Single-Precision Floatin.
Vol. 2A 3-63 INSTRUCTION SE T REF ERENCE, A-M ANDNPS—Bitwise Logical AND NOT of Packed Single-Precision Floating-Point Values Real-Address Mode Ex ceptions #GP(0) If a memory operand is not aligned on a 16-byte boundary , regardless of segment. If any part of the operand lies outside the effective address space from 0 to FFFFH.
3-64 Vol. 2A ARPL—Adjust RPL Field of Segment Selector INSTRUCTION SE T REF ERENCE, A-M ARPL —Adjust RPL Field o f Segmen t Selector Descripti on Compares the RPL fields of two segment selectors. The first operand (the destination operand) contains one segment selector and the second operand (source operand) contains the other .
Vol. 2A 3-65 INSTRUCTION SE T REF ERENCE, A-M ARPL—Adjust RPL Field of Segment Selector ELSE ZF ← 0; FI; FI; Flags A ffected The ZF flag is set to 1 if the RPL field of the destination operand is less than that of the source operand; otherwise, it is set to 0.
3-66 Vol. 2A BOUND—Check Array Index Against Bounds INSTRUCTION SE T REF ERENCE, A-M BOUND—Check Arra y In dex Agains t Bounds Descripti on BOUND determines if the first operand (arra y index) is within the bounds of an array specified the second operand (bounds operand).
Vol. 2A 3-67 INSTRUCTION SE T REF ERENCE, A-M BOUND—Check Array Index Against Bounds Flags A ffected None. Pr otected Mode Ex ceptions #BR If the bounds test fails. #UD If second operand is not a memory location. If the LOCK prefix is used. #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit.
3-68 Vol. 2A BOUND—Check Array Index Against Bounds INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-69 INSTRUCTION SE T REF ERENCE, A-M BSF—Bit Scan Forward BSF—Bit Scan F orward Description Searches the source operand (second operand) for the least significant set bit (1 bit). If a least significant 1 bit is found, its bit index is stored in the destination operand (first operand).
3-70 Vol. 2A BSF—Bit Scan Forward INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If a memory oper and effectiv e address is outsid e the CS, DS, ES, FS, or GS segment limit. If the DS, ES, FS, or GS register contains a NULL segment selector .
Vol. 2A 3-71 INSTRUCTION SE T REF ERENCE, A-M BSR—Bit Scan Reverse BSR—Bit Scan Re verse Description Searches the source operand (second operand) for the most significant set bit (1 bit). If a most significant 1 bit is found, its bit index is stored in the destination operand (first operand).
3-72 Vol. 2A BSR—Bit Scan R everse INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If a memory oper and effectiv e address is outsid e the CS, DS, ES, FS, or GS segment limit. If the DS, ES, FS, or GS register contains a NULL segment selector .
Vol. 2A 3-73 INSTRUCTION SE T REF ERENCE, A-M BSWAP—Byte Swap BSW AP—Byte S wap Description R everses the byte order of a 32-bit or 64-bit (de stination) register . This instruction is provided for converting little-endian values to big-endian format and vice versa.
3-74 Vol. 2A BSWAP—Byte S wap INSTRUCTION SE T REF ERENCE, A-M DEST[15:8] ← TEMP[23:16]; DEST[23:16] ← TEMP[15:8]; DEST[31:24] ← TEMP[7:0]; FI; Flags A ffected None.
Vol. 2A 3-75 INSTRUCTION SE T REF ERENCE, A-M BT—Bit Test BT—Bit T est Description Selects the bit in a bit string (specified with the first operand, called the bit base) at the bit-position designated by the bit offs et (specified by the second operand) and stores the value of the bit in the CF flag.
3-76 Vol. 2A BT—Bit Test INSTRUCTION SE T REF ERENCE, A-M Or , it may access 2 bytes starting from the memory address for a 16-bit oper and, using this relationship: Effective Address + (2 ∗ (BitOffset DIV 16)) It may do so ev en when only a single byte needs to be accessed to reach the given bit.
Vol. 2A 3-77 INSTRUCTION SE T REF ERENCE, A-M BT—Bit Test Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS(0) If a memory operand effective address is outside the SS segment limit.
3-78 Vol. 2A BTC—Bit Test and Complement INSTRUCTION SE T REF ERENCE, A-M BT C—Bit T est and Complemen t Descripti on Selects the bit in a bit string (specified with the first operand, called the .
Vol. 2A 3-79 INSTRUCTION SE T REF ERENCE, A-M BTC—Bit Test and Complement prefix in the form of REX. W promotes operation to 64 bits. See the summary chart at the beginning of this section for encoding data and limits.
3-80 Vol. 2A BTC—Bit Test and Complement INSTRUCTION SE T REF ERENCE, A-M #AC(0) If alignment checking is enabled and an unaligned memory reference is made. #UD If the LOCK prefix is used but the destination is not a memory operand. Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-81 INSTRUCTION SE T REF ERENCE, A-M BTR—Bit Test and Reset BTR —B it T e st a nd Re set DESCRIPTION Selects the bit in a bit string (specified with the first operand, called the bit base.
3-82 Vol. 2A BTR—Bit Test and Reset INSTRUCTION SE T REF ERENCE, A-M prefix in the form of REX.W promotes oper ation to 64 bits. See the summary chart at the beginning of this section for encoding data and limits.
Vol. 2A 3-83 INSTRUCTION SE T REF ERENCE, A-M BTR—Bit Test and Reset #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made. #UD If the LOCK prefix is used b u t the destination is not a memory operand. Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-84 Vol. 2A BTS—Bit Test and Set INSTRUCTION SE T REF ERENCE, A-M BTS —B it T e st an d S et Descripti on Selects the bit in a bit string (specified with the first operand, called the bit base) a.
Vol. 2A 3-85 INSTRUCTION SE T REF ERENCE, A-M BTS—Bit Test and Set prefix in the form of REX. W promotes operation to 64 bits. See the summary chart at the beginning of this section for encoding data and limits.
3-86 Vol. 2A BTS—Bit Test and Set INSTRUCTION SE T REF ERENCE, A-M #AC(0) If alignment checking is enabled and an unaligned memory reference is made. #UD If the LOCK prefix is used but the destination is not a memory operand. Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-87 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure CA LL —Call Proc edure Description Saves procedure linking information on th e stack and bran ches to the called proce- dure specified using the target operand.
3-88 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M the first instruction in the called procedure. The operand can be an immediate value, a general-purpose register , or a memory location.
Vol. 2A 3-89 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure or 64 bits). In 64-bit mode the target operand will alw ays be 64-bits because the operand size is forced to 64-bits for near branches. Far Calls in Real-Address or Virtual-8086 Mod e.
3-90 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M segment selector for the new code segment and the new instruction pointer (offset) from the call gate descriptor . (The offset from the target oper and is ignored when a call gate is used.
Vol. 2A 3-91 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure Far Calls in Compatibility Mode. When the processor is operating in compatibility mode, the CALL instruction can be used to perform .
3-92 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M pushes the segment selector and stack po inter for the calling procedure’ s stack and the segment selector and instruction po inter for the calling procedure’ s code segment. (Par ameter copy is not supporte d in IA-32e m ode.
Vol. 2A 3-93 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure Note that when using a call gate to perform a far call to a segment at the same priv- ilege level, an implicit stack switch occurs as a result of entering 64-bit mode.
3-94 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M THEN tempRIP ← DEST; (* DEST is r/m64 *) IF stack not lar ge enough for a 8-byte re turn address THEN #SS(0); FI ; Push(RIP); RIP .
Vol. 2A 3-95 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure Push(IP); CS ← DEST[31:16]; (* DEST is ptr1 6:16 or [ m16:16 ] *) EIP ← DEST[15:0]; (* DEST i s ptr16:16 or [ m16: 16 ]; clear u.
3-96 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M tempEIP ← tempEIP AND 0000FFFFH; FI; (* Clear upper 1 6 bits *) IF (EFER.LMA = 0 or targe t mode = Compatibility mode) and (tem pE.
Vol. 2A 3-97 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure tempEIP ← DEST(Offset); IF OperandS ize = 16 THEN tempEIP ← tempEIP AND 0000FFFFH; FI; (* Clear uppe r 16 bits *) IF (EFER.
3-98 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M THEN #GP(code segment selector); FI; Read code segment descri ptor; IF code-segment segme nt descriptor does not indicate a cod e segment or code-segment segment de scriptor DPL > CPL THEN #GP(code segment selector); FI; IF IA32_EFER.
Vol. 2A 3-99 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure or stack segment DPL ≠ DPL of code segment or stack segment is not a writable data s egment) THEN #TS(SS selector); FI IF IA32_EFER.
3-100 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M (* Segment des criptor information al so loaded *) Push(oldSS:oldESP); (* From calling procedure *) Push(oldCS:oldEIP); (* Return a.
Vol. 2A 3-101 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure THEN #GP(task gate selector); FI; IF task gate not present THEN #NP(task gate selector); FI; Read the TS S segment selector in the .
3-102 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M #GP(selector) If a code segment or gate or TSS selector index is outside descriptor table limit s.
Vol. 2A 3-103 INSTRUCTION SE T REF ERENCE, A-M CALL—Call Procedure If the RPL of the new stack segment selector in the TSS is not equal to the DPL of the code segment being accessed. If DPL of the stack segment descriptor for the new stack segment is not equal to the DPL of the code segment descriptor .
3-104 Vol. 2A CALL—Call Procedure INSTRUCTION SE T REF ERENCE, A-M If code segment or 64 -bit call gate overlaps non-canonical space. If the segment descriptor pointed to by the segment selector in the destination operand is not for a conforming-code segment, nonconforming-code segment, or 64-bit call gate.
Vol. 2A 3-105 INSTRUCTION SE T REF ERENCE, A-M CBW/CWDE/CDQE—Convert Byte to Word/Convert Word to Doubleword/Convert Double- word to Quadword CBW/CWDE/CDQE—Con vert Byte to W ord/Con vert W ord to Do ubl eword /C onvert Dou ble word to Qu adwo rd Description Double the size of the source operand by means of sign extension.
3-106 Vol. 2A CLC—Clear Carry Flag INSTRUCTION SE T REF ERENCE, A-M CLC—Clear Carry Flag Descripti on Clears the CF flag in the EFLAGS register . Operation is the same in all non-64-bit modes and 64-bit mode. Operat ion CF ← 0; Flags A ffected The CF flag is set to 0.
Vol. 2A 3-107 INSTRUCTION SE T REF ERENCE, A-M CLD—Clear Direction Flag CLD—Clear Direction Flag Description Clears the DF flag in the EFL AGS register . When the DF flag is set to 0, string ope r a- tions increment the index registers (ESI an d/or EDI).
3-108 Vol. 2A CLFLUSH—Flush Cache Line INSTRUCTION SE T REF ERENCE, A-M CLFL USH—Flush Cache Line Descripti on Inv alidates the cache line that contains th e linear address specified with the source operand from all levels of the processor cache hier archy (data and instruction).
Vol. 2A 3-109 INSTRUCTION SE T REF ERENCE, A-M CLFLUSH—Flush Cache Line Operation Flush_Cache_Line(S RC); Intel C/C + + Compiler Intrinsi c Equivalent s CLFLUSH void _mm_clflush(void cons t *p) Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-110 Vol. 2A CLI — Clear Interrupt Flag INSTRUCTION SE T REF ERENCE, A-M CLI — Clear Interrup t Flag Descripti on If protected-mode virtual interrupts are not enabled, CLI clears the IF flag in the EFLAGS register . No other flags are affe cted. Clearing the IF flag causes the processor to ignore maskable external in terrupts.
Vol. 2A 3-111 INSTRUCTION SE T REF ERENCE, A-M CLI — Clear Interrupt Flag THEN IF IOPL ← CPL THEN IF ← 0; (* Reset Interrupt Flag *) ELSE IF ((IOPL < CPL) and (CPL = 3) and (PVI = 1)) THEN VI.
3-112 Vol. 2A CLI — Clear Interrupt Flag INSTRUCTION SE T REF ERENCE, A-M Virtual-8086 Mode E xc eptions #GP(0) If the CPL is greater (has less privilege) than the IOPL of the current program or procedure. #UD If the LOCK prefix is used. Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-113 INSTRUCTION SE T REF ERENCE, A-M CLTS—Clear Task-Switched Flag in CR0 CL TS—Clear T ask-Switched Flag in CR0 Description Clears the task -switche d (TS) flag in the CR 0 register . This instruction is intended for use in operating-system procedures.
3-114 Vol. 2A CLTS—Clear Task-Switched Flag in CR0 INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-115 INSTRUCTION SE T REF ERENCE, A-M CMC—Complement Carry Flag CMC—Complement Carry Flag Description Complements the CF flag in the EFLAGS re gister . CMC operation is the same in non- 64-bit modes and 64-bit mode. Operation EFLAGS.CF[bit 0] ← NOT EFLAGS.
3-116 Vol. 2A CMOVcc—Conditional Move INSTRUCTION SE T REF ERENCE, A-M CMO V cc —Conditional Mo ve Opcode Instruction 64-Bit Mode Compat/ Leg M ode Descript ion 0F 47 /r CMO V A r16, r/m16 Va lid V alid Move if abov e (CF=0 and ZF=0). 0F 47 /r CMO V A r32, r/m32 Va lid V alid Move if abov e (CF=0 and ZF=0).
Vol. 2A 3-117 INSTRUCTION SE T REF ERENCE, A-M CMOVcc—Conditional Move Opcode Instruction 64-Bit Mode Compat/ Leg Mode Description 0F 4D /r CMOVGE r32, r/m32 V alid Valid Move if grea ter or equa l (SF=OF). REX.W + 0F 4D /r CMOVGE r64, r/m64 Valid N.
3-118 Vol. 2A CMOVcc—Conditional Move INSTRUCTION SE T REF ERENCE, A-M Opcode Instruction 64-Bit Mode Compat/ Leg M ode Descript ion 0F 43 /r CMO VNC r16, r/m16 V alid V alid Mov e if not carry (CF=0 ). 0F 43 /r CMO VNC r32, r/m32 V alid V alid Mov e if not ca rry (CF=0).
Vol. 2A 3-119 INSTRUCTION SE T REF ERENCE, A-M CMOVcc—Conditional Move Opcode Instruction 64-Bit Mode Compat/ Leg Mode Description REX.W + 0F 4B /r CMOVNP r64, r/m64 Va l i d N . E . M ov e i f n o t p a r i t y (PF=0). 0F 49 /r CMOVNS r16, r/m16 V alid V alid Move if no t sign (SF=0).
3-120 Vol. 2A CMOVcc—Conditional Move INSTRUCTION SE T REF ERENCE, A-M Descripti on The CMOV cc instructions check the state of one or more of the status flags in the EFLAGS register (CF , OF , PF , SF , and ZF) and perform a mov e operation if the flags are in a specified state (or condition).
Vol. 2A 3-121 INSTRUCTION SE T REF ERENCE, A-M CMOVcc—Conditional Move DEST ← temp; FI; FI; Flags A ffected None. Pr otected Mode Ex ceptions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit. If the DS, ES, FS, or GS register contains a NULL segment selector .
3-122 Vol. 2A CMOVcc—Conditional Move INSTRUCTION SE T REF ERENCE, A-M 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form. #GP(0) If the memory address is in a non-canonical form. #PF(fault-code) If a page fault occurs.
Vol. 2A 3-123 INSTRUCTION SE T REF ERENCE, A-M CMP—Compare Two Operands CMP—Compare T wo Operands Opcode Instruction 6 4-Bit Mode Compat/ Leg Mode Description 3C ib CMP AL, imm8 Valid V alid Compare imm8 with AL. 3D iw CMP AX, imm16 Valid V alid Compare imm16 with AX.
3-124 Vol. 2A CMP—Compare Two Operands INSTRUCTION SE T REF ERENCE, A-M Descripti on Compares the first source operand with the second source operand and sets the status flags in the EFLAGS register according to the results.
Vol. 2A 3-125 INSTRUCTION SE T REF ERENCE, A-M CMP—Compare Two Operands Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS(0) If a memory operand effective address is outside the SS segment limit.
3-126 Vol. 2A CMPPD—Compare Packed Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M CMPPD—Compare P acked Double-Pr ecision Floating-Point V alues Descripti on Performs a S.
Vol. 2A 3-127 INSTRUCTION SE T REF ERENCE, A-M CMPPD—Compare Packed Double-Precision Floating-Point Values The unordered relationship is true when at least one of the two source operands being compared is a NaN; the ordered relationship is true when neither source operand is a NaN.
3-128 Vol. 2A CMPPD—Compare Packed Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M The greater-than relations that the processor does not implement require more than one instruction to emulate in software an d therefore should not be implemented as pseudo-ops.
Vol. 2A 3-129 INSTRUCTION SE T REF ERENCE, A-M CMPPD—Compare Packed Double-Precision Floating-Point Values CMPPD for inequality __m128d _mm_cmpneq_pd(__m 128d a, __m128d b) CMPPD for not-less-than _.
3-130 Vol. 2A CMPPD—Compare Packed Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .
Vol. 2A 3-131 INSTRUCTION SE T REF ERENCE, A-M CMPPS—Compare Packed Single-Precision Floating-Point Values CMPPS—Compare P acked Single-Pr ecision Floating-Poin t V alues Description Performs a SI.
3-132 Vol. 2A CMPPS—Compare Packed Single-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M The greater-than relations not impl emented by the processor require m ore than one instruction to emulate in software and therefore should not be implemented as pseudo-ops.
Vol. 2A 3-133 INSTRUCTION SE T REF ERENCE, A-M CMPPS—Compare Packed Single-Precision Floating-Point Values THEN DEST95:6 4] ← FFFFFFFFH; ELSE DEST[95:64] ← 00000000H; FI; IF CMP3 = TRUE THEN DES.
3-134 Vol. 2A CMPPS—Compare Packed Single-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M If CPUID.01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. Real-Addr ess Mode Exc eptions #GP(0) If a memory operand is not aligned on a 16-byte boundary , regardless of segment.
Vol. 2A 3-135 INSTRUCTION SE T REF ERENCE, A-M CMPPS—Compare Packed Single-Precision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .
3-136 Vol. 2A CMPS/CMP SB/CMPSW/CMP SD/CMPSQ—Com pare String O perands INSTRUCTION SE T REF ERENCE, A-M CMPS/CMPSB/CMPSW/CMPSD/CMPSQ—Compar e S tring Operands Opcode Instruction 64-Bit Mode Compat.
Vol. 2A 3-137 INSTRUCTION SE T REF ERENCE, A-M CMPS/CMPSB/CMPSW/CMPSD/CMPSQ—Compare String Operands Description Compares the byte, word, doubleword, or qu adword specified with the first source oper.
3-138 Vol. 2A CMPS/CMP SB/CMPSW/CMP SD/CMPSQ—Com pare String O perands INSTRUCTION SE T REF ERENCE, A-M RDI) registers are assumed by the processo r to specify the location of the source operands.
Vol. 2A 3-139 INSTRUCTION SE T REF ERENCE, A-M CMPS/CMPSB/CMPSW/CMPSD/CMPSQ—Compare String Operands (R|E)DI ← (R|E)DI – 2; FI; ELSE IF (Doubleword compa rison) THEN IF DF = 0 THEN (R|E)SI ← (R.
3-140 Vol. 2A CMPS/CMP SB/CMPSW/CMP SD/CMPSQ—Com pare String O perands INSTRUCTION SE T REF ERENCE, A-M (E)SI ← (E)SI – 4; (E)DI ← (E)DI – 4; FI; FI; FI; Flags A ffected The CF , OF , SF , ZF , AF , and PF flags are set according to the temporary result of the comparison.
Vol. 2A 3-141 INSTRUCTION SE T REF ERENCE, A-M CMPS/CMPSB/CMPSW/CMPSD/CMPSQ—Compare String Operands 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form. #GP(0) If the memory address is in a non-canonical form.
3-142 Vol. 2A CMPSD—Compare Scalar Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M CMPSD—Compare Scalar Double-Pr ecision Floating-Point V alues Descripti on Compares the .
Vol. 2A 3-143 INSTRUCTION SE T REF ERENCE, A-M CMPSD—Compare Scalar Double-Precisi on Floating-Point Values The greater-than relations not implemented in the processor require more than one instruction to emulate in software and therefore should not be implemented as pseudo-ops.
3-144 Vol. 2A CMPSD—Compare Scalar Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M CMPSD for greater-than-or-equal__m128d _mm_cmpge_sd(__m12 8d a, __m128d b) CMPSD for inequ.
Vol. 2A 3-145 INSTRUCTION SE T REF ERENCE, A-M CMPSD—Compare Scalar Double-Precisi on Floating-Point Values If CR4.OSFXSR[bit 9] = 0. If CPUID .01H:EDX.SSE2[bit 26] = 0. If the LOCK prefix is used. Virtual-8086 Mode Excep tions Same exceptions as in real address mode.
3-146 Vol. 2A CMPSS—Compare Scalar Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M CMPSS—Compare Scalar Single-Pr e cision Floating-Poin t V alues Descripti on Compares the.
Vol. 2A 3-147 INSTRUCTION SE T REF ERENCE, A-M CMPSS—Compare Scalar Single-Pre cision Floating-Point Values The greater-than relations not implemented in the processor require more than one instruction to emulate in software and therefore should not be implemented as pseudo-ops.
3-148 Vol. 2A CMPSS—Compare Scalar Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M CMPSS for less-than __m128 _mm_ cmplt_ss(__m128 a, __m128 b) CMPSS for less-than-or-equal _.
Vol. 2A 3-149 INSTRUCTION SE T REF ERENCE, A-M CMPSS—Compare Scalar Single-Pre cision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .
3-150 Vol. 2A CMPXCHG—Compare and Exchange INSTRUCTION SE T REF ERENCE, A-M CMP X CHG—Compare and Ex change Descripti on Compares the value in the AL, AX, EAX, or RAX register with the first oper and (desti- nation operand). If the two v alues are equa l, the second operand (source operand) is loaded into the destination operand.
Vol. 2A 3-151 INSTRUCTION SE T REF ERENCE, A-M CMPXCHG—Compare and Exchange In 64-bit mode, the instruction’s default operation size is 32 bits. Use of the REX.R prefix permits access to additional regi sters (R8-R1 5). Use of the REX.W prefix promotes operation to 64 bits.
3-152 Vol. 2A CMPXCHG—Compare and Exchange INSTRUCTION SE T REF ERENCE, A-M Real-Addr ess Mode Exc eptions #GP If a memory operand effectiv e address is outside the CS, DS, ES, FS, or GS segment limit. #SS If a memory operand effective address is outside the SS segment limit.
Vol. 2A 3-153 INSTRUCTION SE T REF ERENCE, A-M CMPXCHG8B/CMPXCHG16B—Compa re and Exchange Bytes CMP X CHG8B/CMP X CHG16B—Compare and Ex change Bytes Description Compares the 64-bit value in EDX:EAX (o r 128-bit value in RDX:RAX if oper and size is 128 bits) with the operand (destination operand).
3-154 Vol. 2A CMPXCHG8B/CMPXCHG16B—Compare and Exchange Bytes INSTRUCTION SE T REF ERENCE, A-M Operat ion IF (64-Bit Mode and OperandSize = 64) THEN IF (RDX:RAX = DEST) ZF ← 1; DEST ← RCX:RBX; E.
Vol. 2A 3-155 INSTRUCTION SE T REF ERENCE, A-M CMPXCHG8B/CMPXCHG16B—Compa re and Exchange Bytes #SS If a memory operand effective address is outside the SS segment limit. Virtual-8086 Mode Excep tions #UD If the destination operand is not a memory location.
3-156 Vol. 2A COMISD—Compare Scalar Ordered Double-Pre cision Floating-Point Values and Set EFLAGS INSTRUCTION SE T REF ERENCE, A-M CO MISD—Compare Scalar Or dered Do uble-Pr ecision Floating-Poin.
Vol. 2A 3-157 INSTRUCTION SE T REF ERENCE, A-M COMISD—Compare Scalar Ordered Double-Pre cision Floating-Point Values and Set EFLAGS int _mm_comile_sd (__m1 28d a, __m128d b) int _mm_comigt_sd (__m12.
3-158 Vol. 2A COMISD—Compare Scalar Ordered Double-Pre cision Floating-Point Values and Set EFLAGS INSTRUCTION SE T REF ERENCE, A-M Virtual-8086 Mode E xc eptions Same exceptions as in real address mode. #PF(fault-code) F or a page fault. #AC(0) If alignment checking is enabled and an unaligned memory reference is made.
Vol. 2A 3-159 INSTRUCTION SE T REF ERENCE, A-M COMISS—Compare Scalar Ordered Single-Preci sion Floating-Point Values and Set EFLAGS COMISS—Compare Scalar Or dered Si ngle-Pr ecision Floating-Point.
3-160 Vol. 2A COMISS—Compare Scalar Ordered Single-Pre cisi on Floating-Point Values and Set EFLAGS INSTRUCTION SE T REF ERENCE, A-M int _mm_comile_ss (__m128 a, __m128 b) int _mm_comigt_ss (_ _m128.
Vol. 2A 3-161 INSTRUCTION SE T REF ERENCE, A-M COMISS—Compare Scalar Ordered Single-Preci sion Floating-Point Values and Set EFLAGS Virtual-8086 Mode Excep tions Same exceptions as in real address mode. #PF(fault -code) For a page fault. #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made.
3-162 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification Descripti on The ID flag (bit 21) in the EFLAGS register in dicates support for the CPUID instruc- tion. If a software procedure can set and clear this flag, the processor e xecuting the procedure supports the CPUID instruction.
Vol. 2A 3-163 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification See also: “Serializing Instructions” in Chapter 7, “Multiple-Processor Management, ” in the Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 3A AP-485, Intel Processor Identification and the CPUID In struction (Order Number 241618) T able 3-12.
3-164 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M CPUID lea ves > 3 < 800000 00 are visible on ly when IA32_MISC_ENABLES.BOO T_NT4 [bit 22] = 0 (de fault). Deterministic Cache Par a me ters Leaf 04H NO TES : 04H output depends o n the initial value in ECX .
Vol. 2A 3-165 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification MONIT OR/MWAIT L eaf 5H EAX Bits 15-00: Sm allest monitor-line size in bytes (de fault is process or's monito r granula r.
3-166 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M 0AH EAX Bit s 07 - 00: V ersion ID of architectural performance monitoring Bits 15- 08: Numb er of gener al-purpose perf orman.
Vol. 2A 3-167 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification EDX Bits 10-0: Reserv ed Bit 11: S YSCAL L/SY SRET av ailable (when in 64-bit mod e) Bits 19-12: Rese rved = 0 Bit 20: Execute.
3-168 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M INPUT EAX = 0: R eturns CPUID’ s Highest V a lue for Basic Pr ocessor In formation and the V e ndor Iden tification String When CPUID executes with EAX set to 0, the processor returns the highest v alue the CPUID recognizes for returning basic processo r information.
Vol. 2A 3-169 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification IA32_BIOS_SIGN _ID R eturns Mi crocode Update Signatur e For processors that support the microcode update facility , the IA32_BIOS_SIGN_ID MSR is loaded with the update signature whenever CPUID executes.
3-170 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M See T able 3-14 for available processor type v alues. Stepping IDs are provided as needed.
Vol. 2A 3-171 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification (* Right justify and ze ro-extend 4-bit field. *) FI; (* Show Display_Family as HEX fiel d. *) The Extended Model ID needs to be examined only when the F amily ID is 06H or 0FH.
3-172 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M Figur e 3-6. F eature In formatio n R eturned in the ECX R egister OM16524 b CNXT-ID — L1 Context ID 0 1 2 3 4 5 6 7 8 9 10 .
Vol. 2A 3-173 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification T able 3-15. F eature Inf ormation Returned in the ECX Register Bit # Mnemonic Description 0 SSE3 S treaming SIMD Exte nsions 3 (SSE3) . A value o f 1 indicates the pro cessor supports this technology.
3-174 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M 21 - 22 Re se rved Reser ved 23 POPCNT A value of 1 indicates tha t the processo r supp orts the PO PCNT instruction. 31 - 24 Re se rved Reser ved Figure 3-7 . F eature In formation R eturned in the ED X Regist er T able 3-15.
Vol. 2A 3-175 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification T able 3-16. More on F eature Inf ormation Returned in the EDX R egister Bit # Mnemonic Descrip tion 0 FPU Floating P oint Unit On-Chip. The pr ocessor c ontains an x87 FPU. 1 VME Virtual 8086 Mode Enhance ments.
3-176 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M 13 PGE PTE Global Bit. The global bit in page dir ectory entri es (PDEs) and page table entries (PT Es) is supported, indicati ng TLB entries that are c ommon to differen t processes an d need not be flushed.
Vol. 2A 3-177 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification INPUT EAX = 2: Cache and TLB In formatio n R eturned in EAX, EBX, ECX, ED X When CPUID executes with EAX set to 2, the processor returns inform ation about the processor’s internal caches and TLBs in the EAX, E BX, ECX, an d EDX registers.
3-178 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M T able 3-17 . Encodi ng of Cache and T LB Descriptor s Descriptor V alue Cache or TLB Description 00H Null descriptor 01H Inst.
Vol. 2A 3-179 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification 56H Data TLB 0: 4 MByte pages, 4-way se t associat ive, 16 en tries 57H Data TLB 0: 4 KByte pages, 4-way associ ative, 16 entr.
3-180 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M Example 3-1. Example o f Cache and TLB Interpre tation The first member of the family of Pentium 4 processors returns the foll.
Vol. 2A 3-181 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification query maximum number of cores per physical package by executi ng CPUID with EAX=4 and ECX=0. INPUT EAX = 5: Returns MONIT OR and MWAIT F eatures When CPUID executes with EAX set to 5, the processor returns information about features available to MONIT OR/MWAIT instructions.
3-182 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M This method (introduced with P entium 4 processors) returns an ASCII br and identifi- cation string and the maximum operating frequency of the processor to the EAX, EBX, ECX, and EDX registers.
Vol. 2A 3-183 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification T able 3-18 shows the brand string that is returned by the first processor in the Pentium 4 processor family .
3-184 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M The Proc essor Brand Inde x Method The br and index method (introduced with P entium ® III Xe on ® processors) provides an entry point into a brand identification table that is maintained in memory by system software and is accessible from system- and user-lev el code.
Vol. 2A 3-185 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification do not support the brand identification feature. Starting with processor signature family ID = 0FH, model = 03 H, br and inde x method is no longer supported. Use brand string method instead.
3-186 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M IA-32 Architecture Compat ibility CPUID is not supported in early models of the Intel486 processor or in any IA-32 processor earlier than the Intel486 processor .
Vol. 2A 3-187 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification BREAK EAX = 4H: EAX ← Deterministic Cache Para meters Leaf; (* See Table 3-12.
3-188 Vol. 2A CPUID—CPU Identification INSTRUCTION SE T REF ERENCE, A-M EAX = 80000002H: EAX ← Processor Brand String ; EBX ← Processor Brand St ring, continued; ECX ← Processor Brand String, .
Vol. 2A 3-189 INSTRUCTION SE T REF ERENCE, A-M CPUID—CPU Identification EAX ← Reserved; (* Information ret urned for highest basic information leaf. *) EBX ← Reserved; (* Information ret urned for highest basic information leaf. *) ECX ← Reserved; (* Information retu rned for highest basic information le af.
3-190 Vol. 2A CVTDQ2PD—Convert Packed Doubleword Integers to Packed Double-Precision Floating- Point V alues INSTRUCTION SE T REF ERENCE, A-M CVTDQ2PD—Con vert P ack ed Doubleword In tegers to P a.
Vol. 2A 3-191 INSTRUCTION SE T REF ERENCE, A-M CVTDQ2PD—Convert Packed Doubleword Intege rs to Packed Double-Precision Floating- Point Values If CPUID .01H:EDX.SSE2[bit 26] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
3-192 Vol. 2A CVTDQ2PS—Convert Packed Doubleword Intege rs to Packed Sin gle-Precision Floating- Point V alues INSTRUCTION SE T REF ERENCE, A-M CVTDQ2PS—Conv ert Pack ed Doubleword In tegers to P .
Vol. 2A 3-193 INSTRUCTION SE T REF ERENCE, A-M CVTDQ2PS—Convert Packed Doubleword Integers to Packed Si ngle-Precision Floating- Point Values #NM If CR0.TS[bit 3] = 1. #XM If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 1.
3-194 Vol. 2A CVTDQ2PS—Convert Packed Doubleword Intege rs to Packed Sin gle-Precision Floating- Point V alues INSTRUCTION SE T REF ERENCE, A-M #NM If CR0.TS[bit 3] = 1. #XM If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 1.
Vol. 2A 3-195 INSTRUCTION SE T REF ERENCE, A-M CVTPD2DQ—Convert Packed Double-Precision Floating-Point Values to Packed Double- word Integers CVTPD2DQ—Con vert P ack ed Double-Pre cision Floating-.
3-196 Vol. 2A CVTPD2DQ—Conv ert Packed Double-Precision Floating-Point Values to Packed Double- word Integers INSTRUCTION SE T REF ERENCE, A-M If a memory operand is not aligned on a 16-byte boundary , regardless of segment. #SS(0) For an illegal address in the SS segment.
Vol. 2A 3-197 INSTRUCTION SE T REF ERENCE, A-M CVTPD2DQ—Convert Packed Double-Precision Floating-Point Values to Packed Double- word Integers #GP(0) If the memory address is in a non-canonical form. If memory operand is not aligned on a 16-byte boundary , regardless of segment.
3-198 Vol. 2A CVTPD2PI—Convert Packed Double-Precision Floating-Point Values to Packed Double- word Integers INSTRUCTION SE T REF ERENCE, A-M CVTPD2PI—Con vert P ack ed Double-Pre cision Floating-.
Vol. 2A 3-199 INSTRUCTION SE T REF ERENCE, A-M CVTPD2PI—Convert Packed Double-Precision Floating-Point Values to Packed Double- word Integers Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-200 Vol. 2A CVTPD2PI—Convert Packed Double-Precision Floating-Point Values to Packed Double- word Integers INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-201 INSTRUCTION SE T REF ERENCE, A-M CVTPD2PS—Convert Packed Double-Precision Floating-Point Values to Packed Single- Precision Floating-Point Values CVTPD2PS—Con vert P acked Dou ble-Pr.
3-202 Vol. 2A CVTPD2PS—Convert Packed Double-Precision Floating-Point Values to Packed Single- Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #SS(0) For an illegal address in the SS segment. #PF(fault-code) F or a page fault. #NM If CR0.
Vol. 2A 3-203 INSTRUCTION SE T REF ERENCE, A-M CVTPD2PS—Convert Packed Double-Precision Floating-Point Values to Packed Single- Precision Floating-Point Values 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form.
3-204 Vol. 2A CVTPI2PD—Convert Packed Doubleword Integers to P acked Double-Precision Floating- Point V alues INSTRUCTION SE T REF ERENCE, A-M CVTPI2PD—Con vert P ack ed Doubleword In tegers to P .
Vol. 2A 3-205 INSTRUCTION SE T REF ERENCE, A-M CVTPI2PD—Convert Packed Doubleword Intege rs to Packed Double-Precision Floating- Point Values Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-206 Vol. 2A CVTPI2PD—Convert Packed Doubleword Integers to P acked Double-Precision Floating- Point V alues INSTRUCTION SE T REF ERENCE, A-M #MF If there is a pending x87 FPU ex ception. #UD I f CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .
Vol. 2A 3-207 INSTRUCTION SE T REF ERENCE, A-M CVTPI2PS—Convert Packed Doubleword Integers to Packed Single -Precision Floating- Point Values CVTPI2PS—Con vert P ack ed Doublewor d Integers to P a.
3-208 Vol. 2A CVTPI2PS—Convert Packed Doubleword Intege rs to Packed Single-Precision Floating- Point V alues INSTRUCTION SE T REF ERENCE, A-M #PF(fault-code) F or a page fault. #NM If CR0.TS[bit 3] = 1. #MF If there is a pending x87 FPU ex ception.
Vol. 2A 3-209 INSTRUCTION SE T REF ERENCE, A-M CVTPI2PS—Convert Packed Doubleword Integers to Packed Single -Precision Floating- Point Values 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form.
3-210 Vol. 2A CVTPS2DQ—Convert Packed Single-Precision Floating-Poi nt Values to Packed Double- word Integers INSTRUCTION SE T REF ERENCE, A-M CVTPS2DQ—Conv ert Pack ed Single-Precision Floating-P.
Vol. 2A 3-211 INSTRUCTION SE T REF ERENCE, A-M CVTPS2DQ—Convert Packed Single-Precision Floating-Point Values to Packed Double- word Integers #SS(0) For an illegal address in the SS segment. #PF(fault -code) For a page fault. #NM If CR0.TS[bit 3] = 1.
3-212 Vol. 2A CVTPS2DQ—Convert Packed Single-Precision Floating-Poi nt Values to Packed Double- word Integers INSTRUCTION SE T REF ERENCE, A-M If memory oper and is not aligned on a 16-byte boundary , regardless of segment. #PF(fault-code) F or a page fault.
Vol. 2A 3-213 INSTRUCTION SE T REF ERENCE, A-M CVTPS2PD—Convert Packed Single-Precision Floating-Point Values to Packed Double- Precision Floating-Point Values CVTPS2PD—Con vert Pa cked Single-Pr .
3-214 Vol. 2A CVTPS2PD—Convert Packed Single-Prec ision Floating-Point Values to Packed Double- Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.
Vol. 2A 3-215 INSTRUCTION SE T REF ERENCE, A-M CVTPS2PD—Convert Packed Single-Precision Floating-Point Values to Packed Double- Precision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.
3-216 Vol. 2A CVTPS 2PI—Convert Packed Single-Precision Floating-Point Values to Packed Double- word Integers INSTRUCTION SE T REF ERENCE, A-M CVTPS2PI—Con vert P ack ed Single-Precision Floating-.
Vol. 2A 3-217 INSTRUCTION SE T REF ERENCE, A-M CVTPS2PI—Convert Packed Single-Precision Floating-Point Values to Packe d Double- word Integers Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-218 Vol. 2A CVTPS 2PI—Convert Packed Single-Precision Floating-Point Values to Packed Double- word Integers INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-219 INSTRUCTION SE T REF ERENCE, A-M CVTSD2SI—Convert Scalar Double-Precision Fl oating-Point Value to Doubleword Integer CVTSD2SI—Con vert Scalar Double-Pre cision Floating-P oint V alu.
3-220 Vol. 2A CVTSD2SI—Convert Scalar Double-Precision Floating-Point Value to Doubleword Integer INSTRUCTION SE T REF ERENCE, A-M SIMD Floating-Poin t Ex ceptions Invalid, Precision. Pro tected Mode Ex ceptions #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents.
Vol. 2A 3-221 INSTRUCTION SE T REF ERENCE, A-M CVTSD2SI—Convert Scalar Double-Precision Fl oating-Point Value to Doubleword Integer Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form.
3-222 Vol. 2A CVTSD2SS—Convert Scalar Double-Precision Floa ting-Point Value to Scalar Singl e-Preci- sion Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M CVTSD2SS—Conv ert Scalar Double-Pre.
Vol. 2A 3-223 INSTRUCTION SE T REF ERENCE, A-M CVTSD2SS—Convert Scalar Double-Precision Floating-Point Value to Scalar Singl e-Preci- sion Floating-Point Value #XM If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating -point exception and CR4.
3-224 Vol. 2A CVTSD2SS—Convert Scalar Double-Precision Floa ting-Point Value to Scalar Singl e-Preci- sion Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M #XM If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating-point exception and CR4.
Vol. 2A 3-225 INSTRUCTION SE T REF ERENCE, A-M CVTSI2SD—Convert Doubleword Integer to Scalar Double-P recision Floating-Point Value CVTSI2SD—Con vert Doublewor d Integer to Scalar Double-Precision.
3-226 Vol. 2A CVTSI2SD—Convert Doubleword Integer to Scalar Double-Precision Floating-Poin t Value INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents.
Vol. 2A 3-227 INSTRUCTION SE T REF ERENCE, A-M CVTSI2SD—Convert Doubleword Integer to Scalar Double-P recision Floating-Point Value 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form. #GP(0) If the memory address is in a non-canonical form.
3-228 Vol. 2A CVTSI2SS—Convert Doubleword In teger to Scalar Single-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M CVTSI2SS—Con vert Doublew ord In teger to Scalar Single-Precisi .
Vol. 2A 3-229 INSTRUCTION SE T REF ERENCE, A-M CVTSI2SS—Convert Doubleword Integer to Scalar Single-Prec ision Floating-Point Value SIMD Floating-Point Ex ceptions Precision. Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-230 Vol. 2A CVTSI2SS—Convert Doubleword In teger to Scalar Single-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-231 INSTRUCTION SE T REF ERENCE, A-M CVTSS2SD—Convert Scalar Single-Pre cision Fl oating-Point Value to S calar Double-Preci- sion Floating-Point Value CVTSS2SD—Con vert Scalar Single- P.
3-232 Vol. 2A CVTSS2SD—Convert Scalar Single-Precision Fl oating-Point Value to Scalar Double-Preci- sion Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.
Vol. 2A 3-233 INSTRUCTION SE T REF ERENCE, A-M CVTSS2SD—Convert Scalar Single-Pre cision Fl oating-Point Value to S calar Double-Preci- sion Floating-Point Value #UD If an unmasked SIMD floating-point exception and CR4.OSXMMEXCPT[bit 10] = 0exception and CR4.
3-234 Vol. 2A CVTSS2SI—Convert Scalar Single-Precis ion Floating-Point Value to Doubleword Integer INSTRUCTION SE T REF ERENCE, A-M CVTSS2SI—Conv ert Scalar Single-Precision Floating-Poin t V alue.
Vol. 2A 3-235 INSTRUCTION SE T REF ERENCE, A-M CVTSS2SI—Convert Scalar Single-Precision Floating-Point Value to Doubleword Integer SIMD Floating-Point Ex ceptions Inv alid, Precision. Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-236 Vol. 2A CVTSS2SI—Convert Scalar Single-Precis ion Floating-Point Value to Doubleword Integer INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-237 INSTRUCTION SE T REF ERENCE, A-M CVTTPD2PI—Convert with Truncation Packed Do uble-Precision Floating-Point Values to Packed Doubleword Integers CVTTPD2PI—Con vert with T runcati on P.
3-238 Vol. 2A CVTTPD2PI—Convert with Truncation Packed Double-Preci sion Floating-Point Values to Packed Doubleword Integers INSTRUCTION SE T REF ERENCE, A-M If a memory operand is not aligned on a 16-byte boundary , regardless of segment. #SS(0) For an illegal address in the SS segment.
Vol. 2A 3-239 INSTRUCTION SE T REF ERENCE, A-M CVTTPD2PI—Convert with Truncation Packed Do uble-Precision Floating-Point Values to Packed Doubleword Integers 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form.
3-240 Vol. 2A CVTTPD2DQ—Convert with Truncation Packed Double-Precision Floating-Point Values to Packed Doubleword Integers INSTRUCTION SE T REF ERENCE, A-M CVTTPD2DQ—Con vert with T runcati on P .
Vol. 2A 3-241 INSTRUCTION SE T REF ERENCE, A-M CVTTPD2DQ—Convert with Truncation Packed Double-Precision Floating-Point Values to Packed Doubleword Integers If a memory operand is not aligned on a 16-byte boundary , regardless of segment. #SS(0) For an illegal address in the SS segment.
3-242 Vol. 2A CVTTPD2DQ—Convert with Truncation Packed Double-Precision Floating-Point Values to Packed Doubleword Integers INSTRUCTION SE T REF ERENCE, A-M #GP(0) If the memory address is in a non-canonical form. If memory oper and is not aligned on a 16-byte boundary , regardless of segment.
Vol. 2A 3-243 INSTRUCTION SE T REF ERENCE, A-M CVTTPS2DQ—Convert with Truncation Packed Si ngle-Precision Floating-P oint Values to Packed Doubleword Integers CVTTPS2DQ—Conv ert with Truncation P .
3-244 Vol. 2A CVTTPS2DQ—Convert with Truncation Packed Si ngle-Precision Floating-Point Values to Packed Doubleword Integers INSTRUCTION SE T REF ERENCE, A-M #PF(fault-code) F or a page fault. #NM If CR0.TS[bit 3] = 1. #XM If an unmasked SIMD floating-point exception and CR4.
Vol. 2A 3-245 INSTRUCTION SE T REF ERENCE, A-M CVTTPS2DQ—Convert with Truncation Packed Si ngle-Precision Floating-P oint Values to Packed Doubleword Integers #PF(fault -code) For a page fault. #NM If CR0.TS[bit 3] = 1. #XM If an unmasked SIMD floating -point exception and CR4.
3-246 Vol. 2A CVTTPS2PI—Convert with Truncation Packed Single-P recision Floating-Point Values to Packed Doubleword Integers INSTRUCTION SE T REF ERENCE, A-M CVTTPS2PI—Con vert with T runcation Pa.
Vol. 2A 3-247 INSTRUCTION SE T REF ERENCE, A-M CVTTPS2PI—Convert with Truncation Packed Single-P recision Floating-Point Values to Packed Doubleword Integers Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-248 Vol. 2A CVTTPS2PI—Convert with Truncation Packed Single-P recision Floating-Point Values to Packed Doubleword Integers INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-249 INSTRUCTION SE T REF ERENCE, A-M CVTTSD2SI—Convert with Truncation Scalar Do uble-Precision Floating-Point Value to Signed Doubleword Integer CVTTSD2SI—Con vert with T runcation Scal.
3-250 Vol. 2A CVTTSD2SI—Convert with Truncatio n Scalar Double-Precision Floating-Point Value to Signed Doub leword Intege r INSTRUCTION SE T REF ERENCE, A-M Intel C/C + + Compiler Intrinsic Equivalent int _mm_cvttsd_ si32(__m128d a) SIMD Floating-Poin t Ex ceptions Invalid, Precision.
Vol. 2A 3-251 INSTRUCTION SE T REF ERENCE, A-M CVTTSD2SI—Convert with Truncation Scalar Do uble-Precision Floating-Point Value to Signed Doubleword Integer #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made. Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-252 Vol. 2A CVTTSS2SI—Convert with Truncation Scalar Single-Precision Floating-Point Value to Doubleword Integer INSTRUCTION SE T REF ERENCE, A-M CVTTSS2SI—Con vert with T runcation S calar Sing.
Vol. 2A 3-253 INSTRUCTION SE T REF ERENCE, A-M CVTTSS2SI—Convert with Truncation Scalar Singl e-Precision Floating-Point Value to Doubleword Integer Intel C/C + + Compiler Intrinsi c Equivalent int _mm_cvttss_si32(__m128d a) SIMD Floating-Point Ex ceptions Inv alid, Precision.
3-254 Vol. 2A CVTTSS2SI—Convert with Truncation Scalar Single-Precision Floating-Point Value to Doubleword Integer INSTRUCTION SE T REF ERENCE, A-M #AC(0) If alignment checking is enabled and an unaligned memory reference is made. Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-255 INSTRUCTION SE T REF ERENCE, A-M CWD/CDQ/CQO—Convert Word to Doubleword/Convert Doubleword to Quadword CWD/CDQ/C QO—Conv ert Wor d to Doubleword /Conv ert Doublewor d to Quadwor d De.
3-256 Vol. 2A CWD/CDQ/CQO—Convert Word to Doubleword/Convert Doubleword to Quadword INSTRUCTION SE T REF ERENCE, A-M RDX ← SignExtend(RA X); FI; FI; Flags A ffected None.
Vol. 2A 3-257 INSTRUCTION SE T REF ERENCE, A-M DAA—Decimal Adjust AL after Addition DAA—Decimal Adjust A L after Addition Description Adjusts the sum of two packed BCD values to create a packed BCD result. The AL register is the implied source and destination operand.
3-258 Vol. 2A DAA—Decimal Adjust AL after Addition INSTRUCTION SE T REF ERENCE, A-M Example ADD AL, BL Before : AL = 79H BL = 35H EFLAGS(OSZAP C) = XXXXXX After: AL = AEH BL = 35H EFLAGS(0SZAPC) = 1.
Vol. 2A 3-259 INSTRUCTION SE T REF ERENCE, A-M DAS—Decimal Adjust AL after Subtraction DAS—Decimal Adjust A L after Subtr action Description Adjusts the result of the subtraction of two packed BCD values to create a packed BCD result. The AL register is the implie d source and destination operand.
3-260 Vol. 2A DAS—Decimal Adjust AL after Subtraction INSTRUCTION SE T REF ERENCE, A-M Example SUB AL, BL Before : AL = 35H, BL = 47H, EFLAGS(OSZAPC) = XXXXXX After: AL = EEH, BL = 47H, EFLAGS(0SZAP.
Vol. 2A 3-261 INSTRUCTION SE T REF ERENCE, A-M DEC—Decrement by 1 DEC—Decremen t by 1 Description Subtracts 1 from the destination operand, wh ile preserving the state of the CF flag. The destination operand can be a register or a memory location.
3-262 Vol. 2A DEC—Decrement by 1 INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If the destination operand is located in a non-writable segment. If a memory oper and effective address is outside the CS , DS, ES, FS, or GS segment limit.
Vol. 2A 3-263 INSTRUCTION SE T REF ERENCE, A-M DEC—Decrement by 1 #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3. #UD If the LOCK prefix is used b u t the destination is not a memory operand.
3-264 Vol. 2A DIV—Unsigned Divide INSTRUCTION SE T REF ERENCE, A-M DIV—Unsigned Divide Descripti on Divides unsigned the v alue in the AX, DX:AX, EDX:EAX, or RDX:RAX registers (divi- dend) by the source operand (divisor) and stores the result in the AX (AH:AL), DX:AX, EDX:EAX, o r RDX:RAX registers.
Vol. 2A 3-265 INSTRUCTION SE T REF ERENCE, A-M DIV—Unsigned Divide Operation IF SRC = 0 THEN #DE; FI; (* Divide Error *) IF OperandSiz e = 8 (* Word/Byte Operation *) THEN temp ← AX / SRC; IF temp.
3-266 Vol. 2A DIV—Unsigned Divide INSTRUCTION SE T REF ERENCE, A-M ELSE IF 64-Bit Mode and Operandsize = 64 (* Doublequadword /quadword operation *) THEN temp ← RDX:RAX / SRC; IF temp > FFFFFFF.
Vol. 2A 3-267 INSTRUCTION SE T REF ERENCE, A-M DIV—Unsigned Divide Virtual-8086 Mode Excep tions #DE If the source operand (divisor) is 0. If the quotient is too large for the designated register . #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit.
3-268 Vol. 2A DIVPD—Divide Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M DIVPD—Divide Pack ed Double-Precision Floating-P oint V alues Descripti on Performs a SIMD.
Vol. 2A 3-269 INSTRUCTION SE T REF ERENCE, A-M DIVPD—Divide Packed Double-Precision Floating-Poin t Values #XM If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating -point exception and CR4.
3-270 Vol. 2A DIVPD—Divide Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #XM If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0.
Vol. 2A 3-271 INSTRUCTION SE T REF ERENCE, A-M DIVPS—Divide Packed Single-Precision Floatin g-Point Values DIVPS—Divide Pack ed Single-Precision Floating-Poin t V alues Description Performs a SIMD.
3-272 Vol. 2A DIVPS—Divide Packed Single-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #NM If CR0.TS[bit 3] = 1. #XM If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating-point exception and CR4.
Vol. 2A 3-273 INSTRUCTION SE T REF ERENCE, A-M DIVPS—Divide Packed Single-Precision Floatin g-Point Values #NM If CR0.TS[bit 3] = 1. #XM If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating -point exception and CR4.
3-274 Vol. 2A DIVSD—Divide Scalar Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M DIVSD—Divide Scal ar Double-Precision Floating-P oint V alues Descripti on Divides the low.
Vol. 2A 3-275 INSTRUCTION SE T REF ERENCE, A-M DIVSD—Divide Scalar Double-Precision Floating-P oint Values If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .01H:EDX.SSE2[bit 26] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
3-276 Vol. 2A DIVSD—Divide Scalar Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .01H:E DX.SSE 2[bit 26] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-277 INSTRUCTION SE T REF ERENCE, A-M DIVSS—Divide Scalar Single-Precision Floating-Point Values DIVSS—Divide Scalar Single-Pre cision Floating-Poin t V alues Description Divides the low .
3-278 Vol. 2A DIVSS—Divide Scalar Single-P recision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-279 INSTRUCTION SE T REF ERENCE, A-M DIVSS—Divide Scalar Single-Precision Floating-Point Values If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
3-280 Vol. 2A EMMS—Empty MMX Technology State INSTRUCTION SE T REF ERENCE, A-M EMMS—Emp ty MMX T echnology S tate Descripti on Sets the v alues of all the tags in the x87 FPU tag word to empty (all 1s).
Vol. 2A 3-281 INSTRUCTION SE T REF ERENCE, A-M EMMS—Empty MMX Technology State Virtual-8086 Mode Excep tions Same exceptions as in protected mode. Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions Same exceptions as in protected mode.
3-282 Vol. 2A ENTER—Make Stack Frame for Procedure Parameters INSTRUCTION SE T REF ERENCE, A-M EN TER—Mak e Stack Fr ame f or Proc edure P arame ters Descripti on Creates a stack frame for a procedure.
Vol. 2A 3-283 INSTRUCTION SE T REF ERENCE, A-M ENTER—Make Stack Frame for Procedure Parameters Operation NestingL evel ← NestingLevel M OD 32 IF 64-Bit Mode (StackSize = 64) THEN Push(RBP); FrameT.
3-284 Vol. 2A ENTER—Make Stack Frame for Procedure Parameters INSTRUCTION SE T REF ERENCE, A-M FI; FI; OD; FI; IF 64-Bit Mode (StackSize = 64) THEN Push(FrameTemp); (* Quadword push *) ELSE IF Opera.
Vol. 2A 3-285 INSTRUCTION SE T REF ERENCE, A-M ENTER—Make Stack Frame for Procedure Parameters Real-Address Mode Ex ceptions #SS(0) If the new value of the SP or ESP register is outside the stack segment limit.
3-286 Vol. 2A F2XM1—Compute 2x–1 INSTRUCTION SE T REF ERENCE, A-M F2XM1—Compute 2 x –1 Descripti on Computes the exponential value of 2 to the power of the source operand minus 1. The source operand is located in register ST(0 ) and the result is also stored in ST(0).
Vol. 2A 3-287 INSTRUCTION SE T REF ERENCE, A-M F2XM1—Compute 2x–1 #U Result is too small for destination format. #P V alue cannot be represented exactly in destination format. Pr otected Mode Ex ceptions #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #UD If the LOCK prefix is used.
3-288 Vol. 2A FABS—A bsolute V alue INSTRUCTION SE T REF ERENCE, A-M F ABS—Absolute V alue Descripti on Clears the sign bit of ST(0) to create the absolute value of the operand. Th e following table shows the results obtained when creating the absolute value of v arious classes of numbers.
Vol. 2A 3-289 INSTRUCTION SE T REF ERENCE, A-M FABS—Absolute Value Real- Address Mod e Exc eptions Same exceptions as in protected mode. Virtual-8086 Mo de Ex ceptions Same exceptions as in protected mode. Compatibility Mode Exc eptions Same exceptions as in protected mode.
3-290 Vol. 2A FADD/FADDP/FIADD—Add INSTRUCTION SE T REF ERENCE, A-M F ADD/F ADDP/FIADD—Add Descripti on Adds the destination and source operands an d stores the sum in the destination loca- tion. The destination operand is alw ays an FPU register; the source operand can be a register or a memory location.
Vol. 2A 3-291 INSTRUCTION SE T REF ERENCE, A-M FADD/FADDP/FIADD—Add The table on the following page shows the results obtained wh en adding various classes of numbers, assuming that neither ov erflow nor underflow occurs.
3-292 Vol. 2A FADD/FADDP/FIADD—Add INSTRUCTION SE T REF ERENCE, A-M FPU Flags A ffected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise. C0, C2, C3 Undefined. Floating-Poin t Ex cept ions #IS Stack underflow occurred.
Vol. 2A 3-293 INSTRUCTION SE T REF ERENCE, A-M FADD/FADDP/FIADD—Add #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #PF(fault -code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made. #UD If the LOCK prefix is used.
3-294 Vol. 2A FBLD—Load Binary Coded Decimal INSTRUCTION SE T REF ERENCE, A-M FBLD—Load Binary Coded Decimal Descripti on Converts the BCD source oper and into do uble extended-precision floating-point format and pushes the v alue onto the FP U stack.
Vol. 2A 3-295 INSTRUCTION SE T REF ERENCE, A-M FBLD—Load Binary Coded Decimal Real-Address Mode Ex ceptions #GP If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit. #SS If a memory operand effective address is outside the SS segment limit.
3-296 Vol. 2A FBSTP—Store BCD Integer and Pop INSTRUCTION SE T REF ERENCE, A-M FBSTP—S tor e BCD Integer and P op Descripti on Converts the v alue in the ST(0) register to an 18-digit packed BCD integer , stores the result in the destination ope r and, and pops th e register stack.
Vol. 2A 3-297 INSTRUCTION SE T REF ERENCE, A-M FBSTP—Store BCD Integer and Pop nation operand. If the in valid-oper ation exception is mask ed, the packed BCD indef- inite value is stored in memory . This instruction’ s oper ation is the same in non-64-bit modes and 64-bit mode.
3-298 Vol. 2A FBSTP—Store BCD Integer and Pop INSTRUCTION SE T REF ERENCE, A-M #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #UD If the LOCK prefix is used. Virtual-8086 Mode E xc eptions #GP(0) If a memory operand effe ctive address is outside the CS, DS , ES, FS, or GS segment limit.
Vol. 2A 3-299 INSTRUCTION SE T REF ERENCE, A-M FCHS—Change Sign FCHS—Change Sign Description Complements the sign bit of ST(0). This operation changes a positive value into a negative value of equal magnitude or vice versa. The following table shows the results obtained when changing the sign of v arious classes of numbers.
3-300 Vol. 2A FCHS—Change Sign INSTRUCTION SE T REF ERENCE, A-M Real-Addr ess Mode Exc eptions Same exceptions as in protected mode. Virtual-8086 Mode E xce ptions Same exceptions as in protected mode. Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-301 INSTRUCTION SE T REF ERENCE, A-M FCLEX/FNCLEX—Clear Exceptions FCLEX/FNCL EX —Clear Exc eptions Description Clears the floating-point exception flags (P E, UE, OE, ZE, DE, and IE), the exception summary status flag (ES), the stack fault flag (SF), and the busy flag (B) in the FPU status word.
3-302 Vol. 2A FCLEX/FNCLEX—Clear Exceptions INSTRUCTION SE T REF ERENCE, A-M FPU Flags A ffected The PE, UE, OE, ZE , DE, IE, ES, SF , and B flags in the FPU status word are cleared. The C0, C1, C2, and C3 flags are undefined. Floating-Poin t Ex cept ions None.
Vol. 2A 3-303 INSTRUCTION SE T REF ERENCE, A-M FCMOVcc—Floating-Point Conditional Move FCMO V cc —Floating-Point Conditional Mo ve Description T ests the status flags in the EFLAGS registe r and moves the sou rce oper and (second operand) to the destination oper and (first op erand) if the given test condition is true.
3-304 Vol. 2A FCMOVcc—Floating-Point Conditio nal Move INSTRUCTION SE T REF ERENCE, A-M Operat ion IF condition TR UE THEN ST(0) ← ST(i); FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred. C0, C2, C3 Undefined. Floating-Poin t Ex cept ions #IS Stack underflow occurred.
Vol. 2A 3-305 INSTRUCTION SE T REF ERENCE, A-M FCMOVcc—Floating-Point Conditional Move FC OM/FCOMP/FC OMPP—Compare Floa ting Poin t V a lues Description Compares the contents of register ST(0) and source v alue and sets condition code flags C0, C2, and C3 in the FPU status word according to the results (see the table below).
3-306 Vol. 2A FCMOVcc—Floating-Point Conditio nal Move INSTRUCTION SE T REF ERENCE, A-M The FCOMP instruction pops the register stack following the comparison operation and the FCOMPP in struction pops the regist er stack twice following the comparison operation.
Vol. 2A 3-307 INSTRUCTION SE T REF ERENCE, A-M FCMOVcc—Floating-Point Conditional Move Floating-Point Excep tions #IS Stack underflow occurred. #IA One or both oper ands are NaN values or have unsupported formats. R egister is mark ed empty . #D One or both operands are denormal v alues.
3-308 Vol. 2A FCMOVcc—Floating-Point Conditio nal Move INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-309 INSTRUCTION SE T REF ERENCE, A-M FCOMI/FCOMIP/ FUCOMI/FUCOMIP—Compare Floating Point Values and Set EFLAGS FC OMI/FCOMIP/ FUC OMI/FUC OMIP—Compare Floating Poin t V alues and Set EFL.
3-310 Vol. 2A FCOMI/FCOMIP/ FUCOMI/FUCOMIP—Compare Floating Point Values and Set EFLAGS INSTRUCTION SE T REF ERENCE, A-M If the operation results in an invalid-ari th metic-operand ex ception being r aised, the status flags in the EFLAGS register ar e set only if the exception is masked.
Vol. 2A 3-311 INSTRUCTION SE T REF ERENCE, A-M FCOMI/FCOMIP/ FUCOMI/FUCOMIP—Compare Floating Point Values and Set EFLAGS ZF, PF, CF ← 111; FI; FI; FI; IF Instruction is FCOMIP or FUCOMIP THEN PopRegisterStack; FI; FPU Flags Affected C1 Set to 0 if stack underflow occurred; otherwise, set to 0.
3-312 Vol. 2A FCOS—Cosine INSTRUCTION SE T REF ERENCE, A-M FCOS—Cosine Descripti on Computes the cosine of the source operand in register ST (0) and stores the result in ST(0). The source operand must be given in r adians and must be within the range − 2 63 to + 2 63 .
Vol. 2A 3-313 INSTRUCTION SE T REF ERENCE, A-M FCOS—Cosine ST(0) ← cosine(ST(0)); ELSE (* Source op erand is out-of-ran ge *) C2 ← 1; FI; FPU Flags Affected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise.
3-314 Vol. 2A FDECSTP—Decrement Stack-Top Pointer INSTRUCTION SE T REF ERENCE, A-M FDECSTP—Decremen t S tack-T op P ointer Descripti on Subtracts one from the T OP field of the FPU status word (decrements the top-of- stack pointer). If the T OP field contains a 0, it is set to 7.
Vol. 2A 3-315 INSTRUCTION SE T REF ERENCE, A-M FDECSTP—Decrement Stack-Top Pointer Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-316 Vol. 2A FDIV/FDIVP/FIDIV—Divide INSTRUCTION SE T REF ERENCE, A-M FDIV /FDIVP/FIDIV—Divide Descripti on Divides the destination operand by the source operand and stores th e result in the destination location.
Vol. 2A 3-317 INSTRUCTION SE T REF ERENCE, A-M FDIV/FDIVP/FIDIV—Divide If an unmasked divide-by -zero exception (#Z) is generated, no result is stored; if the exception is masked, an ∞ of the appropriate sign is stored in the destination operand.
3-318 Vol. 2A FDIV/FDIVP/FIDIV—Divide INSTRUCTION SE T REF ERENCE, A-M IF Instruction = FDIVP THEN PopRegisterStack; FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise. C0, C2, C3 Undefined.
Vol. 2A 3-319 INSTRUCTION SE T REF ERENCE, A-M FDIV/FDIVP/FIDIV—Divide Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS(0) If a memory operand effective address is outside the SS segment limit.
3-320 Vol. 2A FDIVR/FDIVRP/FIDIVR—Reverse Divide INSTRUCTION SE T REF ERENCE, A-M FDIVR/FDIVRP/FIDIVR—Re verse Divide Descripti on Divides the source operand by the destination operand and stores the result in the destination location.
Vol. 2A 3-321 INSTRUCTION SE T REF ERENCE, A-M FDIVR/FDIVRP/FIDIVR—Reverse Divide The FIDIVR instructions convert an integer source oper and to double extended-preci- sion floating-point format before performing the division.
3-322 Vol. 2A FDIVR/FDIVRP/FIDIVR—Reverse Divide INSTRUCTION SE T REF ERENCE, A-M DEST ← SRC / DEST; FI; FI; IF Instruction = FDIVRP THEN PopRegisterStack; FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise.
Vol. 2A 3-323 INSTRUCTION SE T REF ERENCE, A-M FDIVR/FDIVRP/FIDIVR—Reverse Divide #SS If a memory operand effective address is outside the SS segment limit.
3-324 Vol. 2A FFREE—Free Floating-Point Register INSTRUCTION SE T REF ERENCE, A-M FFR EE—Free Floating-P oint R egister Descripti on Sets the tag in the FPU tag register associated with register ST(i) to empty (11B). The contents of ST(i) and the FPU stack -top pointer (T OP) are not affected.
Vol. 2A 3-325 INSTRUCTION SE T REF ERENCE, A-M FICOM/FICOMP—Compare Integer FICO M/FICOMP—Compar e Integer Description Compares the value in ST(0) with an inte ger source operand and sets th e condition code flags C0, C2, and C3 in the FPU sta tus word according to the results (see table below).
3-326 Vol. 2A FICOM/FICOMP—Compare Integer INSTRUCTION SE T REF ERENCE, A-M ESAC; IF Instruction = FICOMP THEN PopRegisterStack; FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred; otherwise, set to 0. C0, C2, C3 See table on previous page.
Vol. 2A 3-327 INSTRUCTION SE T REF ERENCE, A-M FICOM/FICOMP—Compare Integer #SS(0) If a memory operand effective address is outside the SS segment limit. #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #PF(fault -code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made.
3-328 Vol. 2A FILD—Load Integer INSTRUCTION SE T REF ERENCE, A-M FILD—Load In teger Descripti on Converts the signed-integer source operand into double extended-precision floating- point format and pushes the v alue onto the FPU register stack. The source oper and can be a word, doubleword, or quadword inte ger .
Vol. 2A 3-329 INSTRUCTION SE T REF ERENCE, A-M FILD—Load Integer #UD If the LOCK prefix is used. Real-Address Mode Ex ceptions #GP If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit. #SS If a memory operand effective address is outside the SS segment limit.
3-330 Vol. 2A FINCSTP—Increment Stack-Top Pointer INSTRUCTION SE T REF ERENCE, A-M FINCSTP—Incremen t S tack-T op Pointer Descripti on Adds one to the TOP field of the FPU st atus word (increments the top-of -stack pointer). If the TOP field contains a 7, it is se t to 0.
Vol. 2A 3-331 INSTRUCTION SE T REF ERENCE, A-M FINCSTP—Increment Stack-Top Pointer Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-332 Vol. 2A FINIT/FNINIT—Initialize Floating-Point Unit INSTRUCTION SE T REF ERENCE, A-M FINIT /FNINIT—Initializ e Floating-Point Unit Descripti on Sets the FPU control, status, tag, instruction pointer , and data pointer registers to their default states.
Vol. 2A 3-333 INSTRUCTION SE T REF ERENCE, A-M FINIT/FNINIT—Initialize Floating-Point Unit Operation FPUControlW ord ← 037FH; FPUStatus Word ← 0; FPUTagWo rd ← FFFFH; FPUDataPoin ter ← 0; FPUInstructionPoin ter ← 0; FPULastInstructionOpcode ← 0; FPU Flags Affected C0, C1, C2, C3 set to 0.
3-334 Vol. 2A FIST/FISTP—Store Integer INSTRUCTION SE T REF ERENCE, A-M FIST /FISTP—S tore In teger Descripti on The FIST instruction converts the value in the ST(0) reg ister to a signed integer and stores the result in the de stination oper and.
Vol. 2A 3-335 INSTRUCTION SE T REF ERENCE, A-M FIST/FISTP—Store Integer If the source value is a non-integral value, it is rounded to an integer value, according to the rounding mode spe cified by th e RC field of the FPU control word.
3-336 Vol. 2A FIST/FISTP—Store Integer INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If the destination is located in a non-writable segment. If a memory oper and effective address is outside the CS , DS, ES, FS, or GS segment limit.
Vol. 2A 3-337 INSTRUCTION SE T REF ERENCE, A-M FIST/FISTP—Store Integer #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #MF If there is a pend ing x87 FPU exception. #PF(fault -code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
3-338 Vol. 2A FISTTP—Store Integer with Truncation INSTRUCTION SE T REF ERENCE, A-M FISTTP—S tor e Integer with T runcation Descripti on FISTTP conv erts the value in ST into a si gned integer using truncation (chop) as rounding mode, transfers the result to the destination, and pop ST .
Vol. 2A 3-339 INSTRUCTION SE T REF ERENCE, A-M FISTTP—Store Integer with Truncation Numeric Ex ceptions Inv alid, Stack Invalid (stack underflow), Precision. Pr otected Mode Ex ceptions #GP(0) If the destination is in a nonwritable segment. For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-340 Vol. 2A FISTTP—Store Integer with Truncation INSTRUCTION SE T REF ERENCE, A-M 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form. #GP(0) If the memory address is in a non-canonical form. #NM CR0.
Vol. 2A 3-341 INSTRUCTION SE T REF ERENCE, A-M FLD—Load Floating Point Value FLD—Load Floating P oint V alue Description Pushes the source operand onto the FPU register stack. The source operand can be in single-precision, double-precision, or do uble extended-precision floating-point format.
3-342 Vol. 2A FLD—Load Floating Point Value INSTRUCTION SE T REF ERENCE, A-M #IA Source op er and is an SNaN. D oes not occur if the source operand is in double extended-p recision floating-point format (FLD m80fp or FLD ST(i)). #D Source operand is a denormal value.
Vol. 2A 3-343 INSTRUCTION SE T REF ERENCE, A-M FLD—Load Floating Point Value Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form.
3-344 Vol. 2A FLD1/FLDL2T/FLDL2E/FLDPI/FLDLG2/FLDLN2/FLDZ—Load Constant INSTRUCTION SE T REF ERENCE, A-M FLD1/FLDL2T /FLDL2E/FLDPI/FLDL G2/FLDLN2/FLDZ—Load Constan t Descripti on Push one of seven commonly used constant s (in double extended-precision floating- point format) onto the FPU register stack.
Vol. 2A 3-345 INSTRUCTION SE T REF ERENCE, A-M FLD1/FLDL2T/FLDL2E/FLDPI/FLDLG2/FLDLN2/FLDZ—Load Constant Floating-Point Excep tions #IS Stack ov erflow occurred. Pr otected Mode Ex ceptions #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #MF If there is a pend ing x87 FPU exception.
3-346 Vol. 2A FLDCW—Load x87 FPU Control Word INSTRUCTION SE T REF ERENCE, A-M FLDCW—Load x87 FPU Con trol W ord Descripti on Loads the 16-bit source operand into the FPU control word. The source operand is a memory location. This instruction is typica lly used to establish or change the FPU’ s mode of operation.
Vol. 2A 3-347 INSTRUCTION SE T REF ERENCE, A-M FLDCW—Load x87 FPU Control Word #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
3-348 Vol. 2A FLDENV—Load x87 FPU Environment INSTRUCTION SE T REF ERENCE, A-M FLDENV—L oad x87 FPU Envir onment Descripti on Loads the comp lete x87 FPU oper ating envi ronm ent from memory into the FPU regis- ters. The source operand specifies the first byte of the oper ating-environment data in memory .
Vol. 2A 3-349 INSTRUCTION SE T REF ERENCE, A-M FLDENV—Load x87 FPU Environment FPU Flags Affected The C0, C1, C2, C3 flags are loaded. Floating-Point Excep tions None; however , if an unma sked ex ception is lo aded in the status word, it is generated upon execution of the next “waiting” floating-point instruction.
3-350 Vol. 2A FLDENV—Load x87 FPU Environment INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-351 INSTRUCTION SE T REF ERENCE, A-M FMUL/FMULP/FIMUL—Multiply FMUL/FMULP/FIMUL—Multiply Description Multiplies the destination and source operan ds and stores the product in the destina- tion location. The destination oper and is always an FPU data register; the source operand can be an FPU data register or a memory location.
3-352 Vol. 2A FMUL /FMULP/FIMUL—Multiply INSTRUCTION SE T REF ERENCE, A-M The FIMUL instructions convert an intege r source oper and to double extended- precision floating-point format before performing the multiplication.
Vol. 2A 3-353 INSTRUCTION SE T REF ERENCE, A-M FMUL/FMULP/FIMUL—Multiply FPU Flags Affected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise. C0, C2, C3 Undef ined. Floating-Point Excep tions #IS Stack underflow occurred.
3-354 Vol. 2A FMUL /FMULP/FIMUL—Multiply INSTRUCTION SE T REF ERENCE, A-M #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #PF(fault-code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory reference is made. #UD If the LOCK prefix is used.
Vol. 2A 3-355 INSTRUCTION SE T REF ERENCE, A-M FNOP—No Operation FNOP—No Operation Description Performs no FPU oper ation. This instruc tio n takes up space in the instruction stream but does not affect the FPU or machin e context, except the EIP register .
3-356 Vol. 2A FPATAN—Partial Arctangent INSTRUCTION SE T REF ERENCE, A-M FP A T AN—P artial Arctangen t Descripti on Computes the arctangent of the source op er and in register ST(1) divided by the source operand in register ST(0), stores the result in ST(1), and pops the FPU register stack.
Vol. 2A 3-357 INSTRUCTION SE T REF ERENCE, A-M FPATAN—Partial Arctangent There is no restriction on the range of source operands that FP A T AN can accept.
3-358 Vol. 2A FPATAN—Partial Arctangent INSTRUCTION SE T REF ERENCE, A-M Floating-Poin t Ex cept ions #IS Stack underflow occurred. #IA Source operand is an SNaN value or unsupported format. #D Source operand is a denormal value. #U Result is too small for destination format.
Vol. 2A 3-359 INSTRUCTION SE T REF ERENCE, A-M FPREM—Partial Remainder FPR EM—Partial R emainder Description Computes the remainder obtained from dividing the value in the ST(0) register (the dividend) by the value in the ST(1) register (the divisor or modu lus ), and stores the result in ST(0).
3-360 Vol. 2A FPREM—Partial Remainder INSTRUCTION SE T REF ERENCE, A-M The FPREM instruction does not compute th e remainder specified in IEEE Std 754. The IEEE specified remainder can be computed with the FPREM1 instruction. The FPREM instruction is provided for compatib ility with the Intel 8087 and Intel287 math coprocessors.
Vol. 2A 3-361 INSTRUCTION SE T REF ERENCE, A-M FPREM—Partial Remainder FPU Flags Affected C0 Set to bit 2 (Q2) of the quotient. C1 Set to 0 if stack underflow o ccurred; otherwise, set to least significant bit of quotient (Q0). C2 Set to 0 if reduction comple te; set to 1 if incomplete.
3-362 Vol. 2A FPREM1—Partial Remainder INSTRUCTION SE T REF ERENCE, A-M FPR EM1—Partial R emainder Descripti on Computes the IEEE remainder obtained from dividing the value in the ST(0) register (the dividend) by the value in the ST(1) register (the divisor or modulus ), and stores the result in ST(0).
Vol. 2A 3-363 INSTRUCTION SE T REF ERENCE, A-M FPREM1—Partial Remainder The FPREM1 instruction computes the rema inder specified in IEEE Standard 754. This instruction operates differently from the FPREM instruction in the w ay that it rounds the quotient of ST(0) divide d by ST(1) to an integer (see the “Operation” section below).
3-364 Vol. 2A FPREM1—Partial Remainder INSTRUCTION SE T REF ERENCE, A-M C2 Set to 0 if reduction complete; set to 1 if incomplete. C3 Set to bit 1 (Q1) of the quotient. Floating-Poin t Ex cept ions #IS Stack underflow occurred. #IA Source operand is an SNaN v alue, modulus (divisor) is 0, divi- dend is ∞ , or unsupported format.
Vol. 2A 3-365 INSTRUCTION SE T REF ERENCE, A-M FPTAN—Partial Tangent F P TA N — P a r t i a l Ta n g e n t Description Computes the tangent of the source operand in register ST(0), stores the result in ST(0), and pushes a 1.0 onto the FPU re gister stack.
3-366 Vol. 2A FPTAN—Partial Tangent INSTRUCTION SE T REF ERENCE, A-M This instruction’s oper ation is the same in non-64-bit modes and 64-bit mode.
Vol. 2A 3-367 INSTRUCTION SE T REF ERENCE, A-M FPTAN—Partial Tangent Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions Same exceptions as in protected mode.
3-368 Vol. 2A FRNDINT—Round to Integer INSTRUCTION SE T REF ERENCE, A-M FRNDIN T—Round t o Integer Descripti on Rounds the source v alue in the ST(0) register to the nearest integral value, depending on the current rounding mode (setting of the RC field of the FPU control word), and stores the result in ST(0).
Vol. 2A 3-369 INSTRUCTION SE T REF ERENCE, A-M FRNDINT—Round to Integer Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions Same exceptions as in protected mode.
3-370 Vol. 2A FRSTOR—Restore x87 FPU State INSTRUCTION SE T REF ERENCE, A-M FRST OR—Res tore x87 FPU S tate Descripti on Loads the FPU state (operating environmen t and register stack) from the memory area specified with the source operand.
Vol. 2A 3-371 INSTRUCTION SE T REF ERENCE, A-M FRSTOR—Restore x87 FPU State ST(7) ← SRC[ST(7)]; FPU Flags Affected The C0, C1, C2, C3 flags are loaded. Floating-Point Excep tions None; however , this oper ation might unmask an existing exception that has been detected but not generated, because it was masked.
3-372 Vol. 2A FRSTOR—Restore x87 FPU State INSTRUCTION SE T REF ERENCE, A-M #AC(0) If alignment checking is enabled and an unaligned memory reference is made. #UD If the LOCK prefix is used. Compatibility Mode Exc e p tions Same exceptions as in protected mode.
Vol. 2A 3-373 INSTRUCTION SE T REF ERENCE, A-M FSAVE/FNSAVE—Store x87 FPU State FSA V E/FNSA VE—S tore x87 FPU S tate Description Stores the current FPU state (operating en vironment and register stack) at the spe c- ified destination in memory , and then re-initializes the FPU.
3-374 Vol. 2A FSAVE/FNSAVE—Store x87 FPU State INSTRUCTION SE T REF ERENCE, A-M instructions separately . If an exception is generated for either of these instructions, the save EIP points to the instruction that caused the exception. This instruction’s oper ation is the same in non-64-bit modes and 64-bit mode.
Vol. 2A 3-375 INSTRUCTION SE T REF ERENCE, A-M FSAVE/FNSAVE—Store x87 FPU State FPU Flags Affected The C0, C1, C2, and C3 flags are sa ved and then cleared. Floating-Point Excep tions None. Pr otected Mode Ex ceptions #GP(0) If destination is located in a non-writable segment.
3-376 Vol. 2A FSAVE/FNSAVE—Store x87 FPU State INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc eptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-377 INSTRUCTION SE T REF ERENCE, A-M FSCALE—Scale FSCAL E—Scale Description T runcates the v alue in the source operand (toward 0) to an integral v alue and adds that value to the exponent of the destin ation operand. The destination and source operands are floating-point v alues located in registers ST(0) and ST(1), respectively .
3-378 Vol. 2A FSCALE—Scale INSTRUCTION SE T REF ERENCE, A-M before the FXTRACT operation was performed. The FSTP ST(1) i nstruction overwrites the exponent (extracted by the FXTRACT inst ruction) with the recreated value, which returns the stack to its original state with only one register [ST(0)] occupied.
Vol. 2A 3-379 INSTRUCTION SE T REF ERENCE, A-M FSIN—Sine FSIN—Sine Description Computes the sine of the source op er and in register ST(0) and stores the result in ST(0). The source operand must be given in radians and must be within the range − 2 63 to + 2 63 .
3-380 Vol. 2A FSIN—Sine INSTRUCTION SE T REF ERENCE, A-M ST(0) ← sin(ST(0)); ELSE (* Source opera nd out of range *) C2 ← 1; FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise. C2 Set to 1 if outside range ( − 2 63 < source operand < + 2 63 ); other- wise, set to 0.
Vol. 2A 3-381 INSTRUCTION SE T REF ERENCE, A-M FSINCOS—Sine and Cosine FSINC OS—Sine and Cosine Description Computes both the sine and the cosine of the source oper and in register ST(0), stores the sine in ST(0), and pushes the cosine onto the top of the FPU register stack.
3-382 Vol. 2A FSINCOS—Sine and Cosine INSTRUCTION SE T REF ERENCE, A-M Operat ion IF ST(0) < 2 63 THEN C2 ← 0; TEMP ← cosine(ST(0)); ST(0) ← sine(ST(0)); TOP ← TOP − 1; ST(0) ← TEMP; ELSE (* Source opera nd out of range *) C2 ← 1; FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred; set to 1 of stack overflow occurs.
Vol. 2A 3-383 INSTRUCTION SE T REF ERENCE, A-M FSINCOS—Sine and Cosine Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions Same exceptions as in protected mode.
3-384 Vol. 2A FSQRT—Square Root INSTRUCTION SE T REF ERENCE, A-M FSQR T—Square R oot Descripti on Computes the square root of the source v alue in the ST(0) register and stores the result in ST(0).
Vol. 2A 3-385 INSTRUCTION SE T REF ERENCE, A-M FSQRT—Square Root Source operand is a negativ e valu e (except for − 0). #D Source operand is a denormal value. #P V alue cannot be represented exactly in destination format. Pr otected Mode Ex ceptions #NM CR0.
3-386 Vol. 2A FST/FSTP—Store Floating Point Value INSTRUCTION SE T REF ERENCE, A-M FST /FSTP—Stor e Floating Poin t V alue Descripti on The FST instruction copies the value in the ST(0) register to the destination operand, which can be a memory location or another register in the FPU register stack.
Vol. 2A 3-387 INSTRUCTION SE T REF ERENCE, A-M FST/FSTP—Store Floating Point Value If the destination operand is a non-empt y register , the inv alid-ope r a tion exception is not generated. This instruction’ s oper ation is the same in non-64-bit modes and 64-bit mode.
3-388 Vol. 2A FST/FSTP—Store Floating Point Value INSTRUCTION SE T REF ERENCE, A-M Real-Addr ess Mode Exc eptions #GP If a memory operand effectiv e address is outside the CS, DS, ES, FS, or GS segment limit. #SS If a memory operand effective address is outside the SS segment limit.
Vol. 2A 3-389 INSTRUCTION SE T REF ERENCE, A-M FSTCW/FNSTCW—Store x87 FPU Control Word FST CW/FNST CW—S tore x87 FPU Con tr ol W ord Description Stores the current value of the FPU contro l word at the specified destination in memory .
3-390 Vol. 2A FSTCW/FNSTCW—Store x87 FPU Control Word INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If the destination is located in a non-writable segment. If a memory oper and effective address is outside the CS , DS, ES, FS, or GS segment limit.
Vol. 2A 3-391 INSTRUCTION SE T REF ERENCE, A-M FSTCW/FNSTCW—Store x87 FPU Control Word #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #MF If there is a pend ing x87 FPU exception. #PF(fault -code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
3-392 Vol. 2A FSTENV/FNSTENV—Stor e x87 FPU Environment INSTRUCTION SE T REF ERENCE, A-M FST ENV /FNST ENV—S tore x87 FPU En vironmen t Descripti on Saves the current FPU oper ating environment at the memory location specified with the destination operand, and then masks al l floating-point exceptions.
Vol. 2A 3-393 INSTRUCTION SE T REF ERENCE, A-M FSTENV/FNSTENV—Store x87 FPU Environment IA-32 Architectur e Compatibility When operating a P e ntium or Intel486 proces sor in MS-DOS compatibility mo.
3-394 Vol. 2A FSTENV/FNSTENV—Stor e x87 FPU Environment INSTRUCTION SE T REF ERENCE, A-M #SS If a memory operand effective address is outside the SS segment limit.
Vol. 2A 3-395 INSTRUCTION SE T REF ERENCE, A-M FSTSW/FNSTSW—Store x87 FPU Status Word FSTSW/FNSTS W—S tore x87 FPU S tatus Wor d Description Stores the current value of the x87 FPU stat us word in the destination location. The destination operand can be either a two-byte memory lo cation or the AX register .
3-396 Vol. 2A FSTSW/FNSTSW—Store x87 FPU Status Word INSTRUCTION SE T REF ERENCE, A-M IA-32 Architecture Compat ibility When operating a P entium or Intel486 proc essor in MS-DOS compatibility mode, it is possible (under unusual circumstances) for an FNSTSW instruction to be interrupted prior to being executed to handle a pending FPU exception.
Vol. 2A 3-397 INSTRUCTION SE T REF ERENCE, A-M FSTSW/FNSTSW—Store x87 FPU Status Word Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS(0) If a memory operand effective address is outside the SS segment limit.
3-398 Vol. 2A FSUB/FSUBP/FISUB—Subtract INSTRUCTION SE T REF ERENCE, A-M FSUB/FSUBP/FISUB—Subtr act Descripti on Subtracts the source oper and from the dest ination oper and and stores the difference in the destination location. The destination oper and is alwa ys an FPU data register; the source operand can be a register or a memory location.
Vol. 2A 3-399 INSTRUCTION SE T REF ERENCE, A-M FSUB/FSUBP/FISUB—Subtract The FISUB instructions convert an integer source operand to double extended-preci- sion floating-point format before performing the subtraction.
3-400 Vol. 2A FSUB/FSUBP/FISUB—Subtract INSTRUCTION SE T REF ERENCE, A-M IF Instruction = FSUBP THEN PopRegisterStack; FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise. C0, C2, C3 Undefined.
Vol. 2A 3-401 INSTRUCTION SE T REF ERENCE, A-M FSUB/FSUBP/FISUB—Subtract Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS(0) If a memory operand effective address is outside the SS segment limit.
3-402 Vol. 2A FSUBR/FSUBRP/FISUBR—Reverse Subtract INSTRUCTION SE T REF ERENCE, A-M FSUBR/FSUBRP/FISUBR—Re verse Subtr act Descripti on Subtracts the destination oper and from the source operand and stores the difference in the destination location.
Vol. 2A 3-403 INSTRUCTION SE T REF ERENCE, A-M FSUBR/FSUBRP/FISUBR—Reverse Subtract the register stack being popped. In some assemblers, the mnemonic for this instruc- tion is FSUBR rather than FSUBRP . The FISUBR instructions convert an integer source operand to double extended- precision floating-point format be fore performing the subtraction.
3-404 Vol. 2A FSUBR/FSUBRP/FISUBR—Reverse Subtract INSTRUCTION SE T REF ERENCE, A-M IF Instruction = FSUBRP THEN PopRegisterStack; FI; FPU Flags A ffected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise. C0, C2, C3 Undefined.
Vol. 2A 3-405 INSTRUCTION SE T REF ERENCE, A-M FSUBR/FSUBRP/FISUBR—Reverse Subtract Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS(0) If a memory operand effective address is outside the SS segment limit.
3-406 Vol. 2A FTST—TEST INSTRUCTION SE T REF ERENCE, A-M FTST—T EST Descripti on Compares the value in the ST(0) register with 0.0 and sets the condition code flags C0, C2, and C3 in the FPU status word according to the results (see table below). This instruction performs an “unordered co mparison.
Vol. 2A 3-407 INSTRUCTION SE T REF ERENCE, A-M FTST—TEST #IA The source oper and is a NaN v alue or is in an unsupported format. #D The source operand is a denormal v alue. Pr otected Mode Ex ceptions #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #MF If there is a pend ing x87 FPU exception.
3-408 Vol. 2A FUCOM/FUCOMP/FUCOMPP—Unordered Compare Floating Point Values INSTRUCTION SE T REF ERENCE, A-M FUCOM /FUCOMP/FUC OMPP—Unorder ed Compar e Floating Poin t V alues Descripti on Performs.
Vol. 2A 3-409 INSTRUCTION SE T REF ERENCE, A-M FUCOM/FUCOMP/FUCOMPP—Unordered Compare Floating Point Values The FUCOMP instruction pops the register stack following the comparison operation and the FUCOMPP instruction pops the regist er stack twice following the comparison operation.
3-410 Vol. 2A FUCOM/FUCOMP/FUCOMPP—Unordered Compare Floating Point Values INSTRUCTION SE T REF ERENCE, A-M #IA One or both operan ds are SNaN values or have unsupported formats. Detection of a QNaN value in and of itself does not raise an invalid-operand ex ception.
Vol. 2A 3-411 INSTRUCTION SE T REF ERENCE, A-M FXAM—ExamineModR/M FXAM—ExamineModR/M Description Examines the contents of the ST(0) register and sets the condition code flags C0, C2, and C3 in the FPU status word to indicate the class of v alue or number in the register (see the table below).
3-412 Vol. 2A FXAM—ExamineModR/M INSTRUCTION SE T REF ERENCE, A-M FPU Flags A ffected C1 Sign of value in ST(0). C0, C2, C3 See T able 3-47. Floating-Poin t Ex cept ions None. Pro tected Mode Ex ceptions #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #MF If there is a pending x87 FPU ex ception.
Vol. 2A 3-413 INSTRUCTION SE T REF ERENCE, A-M FXCH—Exchange Register Contents FX CH—Ex change Regis ter Contents Description Exchanges the contents of registers ST(0) an d ST(i). If no source operand is speci- fied, the contents of ST(0) and ST(1) are exchanged.
3-414 Vol. 2A FXCH—Exchange Register Contents INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #MF If there is a pending x87 FPU ex ception. #UD If the LOCK prefix is used. Real-Addr ess Mode Exc eptions Same exceptions as in protected mode.
Vol. 2A 3-415 INSTRUCTION SE T REF ERENCE, A-M FXRSTOR—Restore x87 FPU, MMX , XMM, and MXCSR State FXRST OR—Rest ore x87 FPU, MMX , XMM, and MX CSR State Description Reloads the x87 FPU, MMX technology , XMM, and MXCSR registers from the 512-byte memory image specified in the source operan d.
3-416 Vol. 2A FXRSTOR—Restore x87 FPU, MMX , XMM, and MXCSR State INSTRUCTION SE T REF ERENCE, A-M x87 FPU and SIMD Floating-Poin t Exc eptions None. Pro tected Mode Ex ceptions #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents.
Vol. 2A 3-417 INSTRUCTION SE T REF ERENCE, A-M FXRSTOR—Restore x87 FPU, MMX , XMM, and MXCSR State Virtual-8086 Mode Excep tions Same exceptions as in real address mode. #PF(fault -code) For a page fault. #AC For unaligned memory reference. #UD If the LOCK prefix is used.
3-418 Vol. 2A FXSAVE—Save x87 FPU, MMX Technology, SSE, and SSE2 State INSTRUCTION SE T REF ERENCE, A-M FXSA V E—Save x87 FPU, MMX T echnology , SSE, and SSE2 S tate Descripti on Saves the current state of the x87 FPU, MMX technology , XMM, and MXCSR registers to a 512-byte memory location specified in the destination operand.
Vol. 2A 3-419 INSTRUCTION SE T REF ERENCE, A-M FXSAVE—Save x87 FPU, MMX Technology, SSE, and SS E2 State The destination operand contains the first by te of the mem ory image, and it must be aligned on a 16-byte boundary .
3-420 Vol. 2A FXSAVE—Save x87 FPU, MMX Technology, SSE, and SSE2 State INSTRUCTION SE T REF ERENCE, A-M T able 3-49. Field Definitions Field Definition FC W x8 7 F P U Co nt rol Word ( 1 6 b i ts). See Figure 8-6 in the Int el® 64 and IA-32 Architectur es Softwar e Dev eloper’s Manual, V olume 1 , for the layout of the x87 FPU c ontr ol wor d.
Vol. 2A 3-421 INSTRUCTION SE T REF ERENCE, A-M FXSAVE—Save x87 FPU, MMX Technology, SSE, and SS E2 State The FXSA VE instruction saves an abridged version of the x87 FPU tag word in the FTW field (unlike the FSAVE instruction, wh ich sa ves the complete tag word).
3-422 Vol. 2A FXSAVE—Save x87 FPU, MMX Technology, SSE, and SSE2 State INSTRUCTION SE T REF ERENCE, A-M Here, a 1 is saved for any valid, zero , or special tag, and a 0 i s sav ed for any empty tag.
Vol. 2A 3-423 INSTRUCTION SE T REF ERENCE, A-M FXSAVE—Save x87 FPU, MMX Technology, SSE, and SS E2 State The J-bit is defined to be the 1-bit binary integer to the left o f the decimal place in the significand. The M-bit is defined to be the mo st significant bit of the fr actional portion of the significand (i.
3-424 Vol. 2A FXSAVE—Save x87 FPU, MMX Technology, SSE, and SSE2 State INSTRUCTION SE T REF ERENCE, A-M XMM2 192 XMM3 208 XMM4 224 XMM5 240 XMM6 256 XMM7 272 XMM8 288 XMM9 304 XMM10 320 XMM11 336 XMM12 352 XMM13 368 XMM14 384 XMM15 400 Res er ve d 416 Res er ve d 432 Res er ve d 448 Res er ve d 464 Res er ve d 480 Res er ve d 496 T able 3-52.
Vol. 2A 3-425 INSTRUCTION SE T REF ERENCE, A-M FXSAVE—Save x87 FPU, MMX Technology, SSE, and SS E2 State Operation IF 64-Bit Mode THEN IF REX.W = 1 Res erve d ST 4/M M4 96 Res erve d ST 5/M M5 112 R.
3-426 Vol. 2A FXSAVE—Save x87 FPU, MMX Technology, SSE, and SSE2 State INSTRUCTION SE T REF ERENCE, A-M THEN DEST ← Save64BitPromote dFxsave(x87 FPU, MM X, XMM7-XMM0, MXCSR); ELSE DEST ← Save64B.
Vol. 2A 3-427 INSTRUCTION SE T REF ERENCE, A-M FXSAVE—Save x87 FPU, MMX Technology, SSE, and SS E2 State #UD If CR0.EM[bit 2] = 1. If CPUID.01H:EDX.FXSR[bit 24] = 0. If the LOCK prefix is used. Virtual-8086 Mode Excep tions Same exceptions as in real address mode.
3-428 Vol. 2A FXSAVE—Save x87 FPU, MMX Technology, SSE, and SSE2 State INSTRUCTION SE T REF ERENCE, A-M Implementation No te The order in which the processor signals general-protection (#GP) and pag.
Vol. 2A 3-429 INSTRUCTION SE T REF ERENCE, A-M FXTRACT—Extract Exponent and Significand FXTRA CT—Extr act Exponent and Significand Description Separates the source value in the ST(0) regi ster into its exponent and significand, stores the exponent in ST(0), and pushes the significand onto the register stack.
3-430 Vol. 2A FXTRACT—Extract Exponent and Significand INSTRUCTION SE T REF ERENCE, A-M #IA Source operand is an SNaN value or unsupported format. #Z ST(0) operand is ± 0. #D Source operand is a denormal value. Pro tected Mode Ex ceptions #NM CR0.EM[bit 2] or CR0.
Vol. 2A 3-431 INSTRUCTION SE T REF ERENCE, A-M FYL2X—Compute y * log2x FYL2X —Compute y ∗ log 2 x Description Computes (ST(1) ∗ log 2 (ST(0))), stores the result in resister ST(1), and pops the FPU register stack. The source operand in ST(0) must be a non-zero positive number .
3-432 Vol. 2A FYL2X—Compute y * log2x INSTRUCTION SE T REF ERENCE, A-M Operat ion ST(1) ← ST(1) ∗ log 2 ST(0); PopRegisterStack; FPU Flags A ffected C1 Set to 0 if stack underflow occurred. Set if result was rounded up; cleared otherwise. C0, C2, C3 Undefined.
Vol. 2A 3-433 INSTRUCTION SE T REF ERENCE, A-M FYL2XP1—Compute y * log2(x +1) FYL2XP1—Compute y ∗ log 2 (x + 1) Description Computes (ST(1) ∗ log 2 (ST(0 ) + 1.
3-434 Vol. 2A FYL2XP1—Compute y * log2(x +1) INSTRUCTION SE T REF ERENCE, A-M equation is used to calculate the scale factor for a particular logarithm base, where n is the logarithm base desired for th e result of the FYL2XP1 instruction: scale factor ← log n 2 This instruction’s oper ation is the same in non-64-bit modes and 64-bit mode.
Vol. 2A 3-435 INSTRUCTION SE T REF ERENCE, A-M HADDPD—Packed Double-FP Horizontal Add HADDPD—Pack ed Double-FP Horizon tal Add Description Adds the double-precision floating-point values in the high and low quadwords of the destination operand and stores the result in the low quadword of the destination operand.
3-436 Vol. 2A HADDPD—Packed Double-FP Horizontal Add INSTRUCTION SE T REF ERENCE, A-M Operat ion xmm1[63:0] = xmm1[63:0] + xmm1[1 27:64]; xmm1[127:64] = xmm2 /m128[63:0] + xmm2/m128[127:64]; Intel C.
Vol. 2A 3-437 INSTRUCTION SE T REF ERENCE, A-M HADDPD—Packed Double-FP Horizontal Add #UD If CR0.EM[bit 2] = 1. For an unmasked Streaming SIMD Extensions numeric excep- tion (CR4.OSXMMEXCPT[bit 10] = 0). If CR4.OSFXSR[bit 9] = 0. If CPUID. 01H:ECX.SSE3[bit 0] = 0.
3-438 Vol. 2A HADDPD—Packed Double-FP Horizontal Add INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID feature flag SSE3 is 0.
Vol. 2A 3-439 INSTRUCTION SE T REF ERENCE, A-M HADDPS—Packed Single-FP Hor izontal Add HADDPS—Pack ed Single-FP Horizon tal Add Description Adds the single-precision floating-point values in the first and second dwords of the destination operand and stores the result in the first dword of the destina tion operand.
3-440 Vol. 2A HADDPS—Packe d Single-FP Horizontal Add INSTRUCTION SE T REF ERENCE, A-M In 64-bit mode, use of the REX.R prefix perm its this instruction to access additional registers (XMM8- XMM15).
Vol. 2A 3-441 INSTRUCTION SE T REF ERENCE, A-M HADDPS—Packed Single-FP Hor izontal Add Real Addr ess Mode Exc eptions GP(0) If any part of the operand would lie outside of the effective address space from 0 to 0FFFFH. If a memory operand is not aligned on a 16-byte boundary , regardless of segment.
3-442 Vol. 2A HADDPS—Packe d Single-FP Horizontal Add INSTRUCTION SE T REF ERENCE, A-M #PF(fault-code) F or a page fault. #NM If CR0.TS[bit 3] = 1. #XM If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating-point exception and CR4.
Vol. 2A 3-443 INSTRUCTION SE T REF ERENCE, A-M HLT—Ha lt HL T—Halt Description Stops instruction execution and places the proce ssor in a HAL T state. An enabled interrupt (including NMI and SMI), a debug exception, the BINIT# signal, the INIT# signal, or the RESET# signal will resume exec ution.
3-444 Vol. 2A HLT—Halt INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions Same exceptions as in protected mode.
Vol. 2A 3-445 INSTRUCTION SE T REF ERENCE, A-M HSUBPD—Packed Double-FP Horizontal Subtract HSUBPD—Pack ed Double-FP Horizont al Subtr act Description The HSUBPD instruction subtracts horizonta lly the packed DP FP numbers of both operands.
3-446 Vol. 2A HSUBPD—Packed Double-FP Horizontal Su btract INSTRUCTION SE T REF ERENCE, A-M Operat ion xmm1[63:0] = xmm1[63:0] − xmm1[127:64]; xmm1[127:64] = xmm2/m128[63:0] − xmm2/m128[12 7:64].
Vol. 2A 3-447 INSTRUCTION SE T REF ERENCE, A-M HSUBPD—Packed Double-FP Horizontal Subtract #UD If CR0.EM[bit 2] = 1. For an unmasked Streaming SIMD Extensions numeric excep- tion (CR4.OSXMMEXCPT[bit 10] = 0). If CR4.OSFXSR[bit 9] = 0. If CPUID. 01H:ECX.
3-448 Vol. 2A HSUBPD—Packed Double-FP Horizontal Su btract INSTRUCTION SE T REF ERENCE, A-M If CPUID feature flag SSE3 is 0. If the LOCK prefix is used.
Vol. 2A 3-449 INSTRUCTION SE T REF ERENCE, A-M HSUBPS—Packed Single-FP Horiz ontal Subtract HSUBPS—Pack ed Single-FP Horizon tal Subtract Description Subtracts the single-precision floating-point .
3-450 Vol. 2A HSUBPS—Packed Single-FP Horizontal Su btract INSTRUCTION SE T REF ERENCE, A-M In 64-bit mode, use of the REX.R prefix perm its this instruction to access additional registers (XMM8- XMM15).
Vol. 2A 3-451 INSTRUCTION SE T REF ERENCE, A-M HSUBPS—Packed Single-FP Horiz ontal Subtract Numeric Ex ceptions Overflow , Underflow , Inv alid, Precision, Denormal. Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-452 Vol. 2A HSUBPS—Packed Single-FP Horizontal Su btract INSTRUCTION SE T REF ERENCE, A-M #NM If CR0.TS[bit 3] = 1. #XM For an unmask ed Streaming SIMD Extensions numeric excep- tion (CR4.OSXMMEXCPT[bit 10] = 1). #UD I f CR0.EM[bit 2] = 1. For an unmask ed Streaming SIMD Extensions numeric excep- tion (CR4.
Vol. 2A 3-453 INSTRUCTION SE T REF ERENCE, A-M IDIV—Signed Divide IDIV—Signed Divide Description Divides the (signed) value in the AX, DX:A X, or EDX:EAX (dividend) by the source operand (divisor) and stores the result in the AX (AH:AL), DX:A X, or EDX:EAX regis- ters.
3-454 Vol. 2A IDIV—Signed Divide INSTRUCTION SE T REF ERENCE, A-M Operat ion IF SRC = 0 THEN #DE; (* Divide error *) FI; IF OperandS ize = 8 (* Word/byte opera tion *) THEN temp ← AX / SRC; (* Sig.
Vol. 2A 3-455 INSTRUCTION SE T REF ERENCE, A-M IDIV—Signed Divide THEN #DE; (* Divide error *) ELSE EAX ← temp; EDX ← EDXE:AX SignedModulus SRC; FI; FI; ELSE IF OperandSize = 64 (* Dou blequadwo.
3-456 Vol. 2A IDIV—Signed Divide INSTRUCTION SE T REF ERENCE, A-M #GP If a memory operand effectiv e address is outside the CS, DS, ES, FS, or GS segment limit. #SS If a memory operand effective address is outside the SS segment limit. #UD If the LOCK prefix is used.
Vol. 2A 3-457 INSTRUCTION SE T REF ERENCE, A-M IMUL—Signed Multiply IMUL —Signed Multiply Opcode Instruction 64-Bit Mode Compat/ Leg Mode Descript ion F6 /5 IMUL r/m8* Va l i d Va l id A X ← AL ∗ r/m byte. F7 /5 IMUL r/m16 Va l i d Val i d DX : A X ← AX ∗ r/m word.
3-458 Vol. 2A IMUL—Signed Multiply INSTRUCTION SE T REF ERENCE, A-M Descripti on Performs a signed multiplication of two op er ands. This instruction has three forms, depending on the number of operands. • One-operand form — This form is identical to that used by the MUL instruction.
Vol. 2A 3-459 INSTRUCTION SE T REF ERENCE, A-M IMUL—Signed Multiply signed or unsigned. The CF and OF flags, ho wever , cannot be used to determine if the upper half of the result is non-zero. In 64-bit mode, the instruction’s default operation size is 32 bits.
3-460 Vol. 2A IMUL—Signed Multiply INSTRUCTION SE T REF ERENCE, A-M ELSE IF (NumberO fOperands = 2) THEN temp ← DEST ∗ SRC (* Signed multipli cation; temp is double DEST size *) DEST ← DEST .
Vol. 2A 3-461 INSTRUCTION SE T REF ERENCE, A-M IMUL—Signed Multiply #SS If a memory operand effective address is outside the SS segment limit. #UD If the LOCK prefix is used. Virtual-8086 Mode Excep tions #GP(0) If a memory op er and effective address is outside the CS, DS, ES, FS, or GS segment limit.
3-462 Vol. 2A IN—Input from Port INSTRUCTION SE T REF ERENCE, A-M IN—Input fr om Port Descripti on Copies the value from the I/O port spec ified with the second operand (source operand) to the destination operand (first oper and).
Vol. 2A 3-463 INSTRUCTION SE T REF ERENCE, A-M IN—Input from Port DEST ← SRC; (* Read from selected I/O port *) FI; ELSE (Real Mode or Pr otected Mode with CPL ≤ IOPL *) DEST ← SRC; (* Read from selected I/O port *) FI; Flags A ffected None.
3-464 Vol. 2A INC—Increment by 1 INSTRUCTION SE T REF ERENCE, A-M INC—Incremen t by 1 Descripti on Adds 1 to the destination op er and, while preserving the state of the CF flag. The destination operand can be a register or a memory location. This instruction allows a loop counter to be updated without distur bing the CF flag.
Vol. 2A 3-465 INSTRUCTION SE T REF ERENCE, A-M INC—Increment by 1 Pr otected Mode Ex ceptions #GP(0) If the destination operand is located in a non-writable segment. If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit.
3-466 Vol. 2A INC—Increment by 1 INSTRUCTION SE T REF ERENCE, A-M #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3. #UD If the LOCK prefix is used but the destination is not a memory operand.
Vol. 2A 3-467 INSTRUCTION SE T REF ERENCE, A-M INS/INSB/INSW/INSD—Input from Port to String INS/INSB/INSW/INSD—Input from P ort to S tring Description Copies the data from the I/O port spec ified with the source operand (second operand) to the destination oper and (first operand).
3-468 Vol. 2A INS/INSB/INSW/INSD—Input from Port to String INSTRUCTION SE T REF ERENCE, A-M destination operand symbol must specify the correct type (size) of the operand (byte, word, or doubleword), but it does not have to specify the correct locati on .
Vol. 2A 3-469 INSTRUCTION SE T REF ERENCE, A-M INS/INSB/INSW/INSD—Input from Port to String IF (Byte transfer) THEN IF DF = 0 THEN (E)DI ← (E)DI + 1; ELSE (E)DI ← (E)DI – 1; FI; ELSE IF (Word .
3-470 Vol. 2A INS/INSB/INSW/INSD—Input from Port to String INSTRUCTION SE T REF ERENCE, A-M #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-471 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure IN T n /INT O/INT 3—Call t o Interrup t Proc edure Description The INT n instruction generates a call to.
3-472 Vol. 2A INT n/INTO/INT 3—Call to Interrupt Procedure INSTRUCTION SE T REF ERENCE, A-M with the IRET instruction, which pops the EFLAGS information and return address from the stack. The interrupt vector number specifies an interrupt descriptor in the interrupt descriptor table (IDT); that is, it provides index into the ID T .
Vol. 2A 3-473 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure When the processor is executing in virt ual-8086 mode, the IOPL determines the action of the INT n instruction.
3-474 Vol. 2A INT n/INTO/INT 3—Call to Interrupt Procedure INSTRUCTION SE T REF ERENCE, A-M CS ← IDT(Descriptor (vector _number ∗ 4), selector)); EIP ← IDT(Descriptor (vector_number ∗ 4), of.
Vol. 2A 3-475 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure or index not w ithin GDT limits THEN #GP(TSS s elector); FI; Access TSS descriptor in GDT; IF TSS descript.
3-476 Vol. 2A INT n/INTO/INT 3—Call to Interrupt Procedure INSTRUCTION SE T REF ERENCE, A-M IF VM = 1 THEN #GP(new code segment selector); FI; IF code segment is confor ming or code se gment DPL = C.
Vol. 2A 3-477 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure or stack segment does not indica te writable data segment THEN #TS(SS sele ctor + EXT); FI; IF stack segme.
3-478 Vol. 2A INT n/INTO/INT 3—Call to Interrupt Procedure INSTRUCTION SE T REF ERENCE, A-M FI; IF 32-bit gate THEN Push(far pointer to old stack); (* Old SS and ESP, 3 words padded to 4 *) Push(EFL.
Vol. 2A 3-479 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure NewESP ← stack address; ELSE (* TSS is 16-bit *) TSSstackAddress ← (n ew code segment DPL ∗ 4) + 2; .
3-480 Vol. 2A INT n/INTO/INT 3—Call to Interrupt Procedure INSTRUCTION SE T REF ERENCE, A-M TempSS ← SS; TempESP ← ESP; SS:ESP ← TS S(SS0:ESP0); (* Change to level 0 stack segment *) (* Follow.
Vol. 2A 3-481 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure IF instruction pointer no t within code segment limit THEN #GP(0); FI; IF 32-bit gate THEN Push (EFLAG S);.
3-482 Vol. 2A INT n/INTO/INT 3—Call to Interrupt Procedure INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If the instruction pointer in the IDT or in the interrupt-, tr ap-, or task gate is beyond the code segment limits. #GP(selector) If the segment selector in th e interrupt-, tr ap-, or task gate is NULL.
Vol. 2A 3-483 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure Real-Address Mode Ex ceptions #GP If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit. If the interrupt vector number is outside the IDT limits.
3-484 Vol. 2A INT n/INTO/INT 3—Call to Interrupt Procedure INSTRUCTION SE T REF ERENCE, A-M If the stack segment for the TS S is not a writable data segment. If segment-selector index for stack segment is outside descriptor table limit s. #PF(fault-code) If a page fault occurs.
Vol. 2A 3-485 INSTRUCTION SE T REF ERENCE, A-M INT n/INTO/INT 3—Call to Interrupt Procedure #TS(selector) If an attempt to load RSP from the TSS causes an access to non- canonical space. If the RSP from the TSS is outside descriptor ta ble limits. #PF(fault -code) If a page fault occurs.
3-486 Vol. 2A INVD—Invalidate Internal Caches INSTRUCTION SE T REF ERENCE, A-M INVD —Inv alidate In ternal Caches Descripti on Inv alidates (flushes) the processor’s internal caches and issues a special-function bus cycle that directs external caches to also flush themselves.
Vol. 2A 3-487 INSTRUCTION SE T REF ERENCE, A-M INVD—Invalidate Internal Caches Pr otected Mode Ex ceptions #GP(0) If the current privilege level is not 0. #UD If the LOCK prefix is used. Real- Address Mod e Exc eptions #UD If the LOCK prefix is used.
3-488 Vol. 2A INVLPG—Invalidate TLB Entry INSTRUCTION SE T REF ERENCE, A-M INVLPG—In validate TLB En try Descripti on Invalidates (flushes) the tr anslation lookas ide buffer (TLB) entry specified with the source operand. The source operand is a memory address.
Vol. 2A 3-489 INSTRUCTION SE T REF ERENCE, A-M INVLPG—Invalidate TLB Entry Real-Address Mode Ex ceptions #UD Operand is a register . If the LOCK prefix is used. Virtual-8086 Mode Excep tions #GP(0) The INVLPG instruction cannot be executed at the virtual-8086 mode.
3-490 Vol. 2A IRET/IRETD—Interrupt Return INSTRUCTION SE T REF ERENCE, A-M IR ET /IR ETD—Interrupt Re turn Descripti on Returns pro gram control from an exception or interrupt handler to a program or procedure that was interrupted by an exception, an external interrupt, or a software- generated i nterrupt.
Vol. 2A 3-491 INSTRUCTION SE T REF ERENCE, A-M IRET/IRETD—Interrupt Return As with a real-address mode interrupt retu rn, the IRET instruction pops the return instruction pointer , return code segme.
3-492 Vol. 2A IRET/IRETD—Interrupt Return INSTRUCTION SE T REF ERENCE, A-M EFLAGS ← (tempEFLAGS AND 257FD5H) OR (EFLAGS AND 1A0000H); ELSE (* OperandSize = 16 *) IF top 6 bytes of stack are not wi.
Vol. 2A 3-493 INSTRUCTION SE T REF ERENCE, A-M IRET/IRETD—Interrupt Return ELSE IF OperandSize = 32 THEN IF top 12 bytes of stack not within stack limits THEN #SS(0); FI; tempEIP ← Pop(); tempCS .
3-494 Vol. 2A IRET/IRETD—Interrupt Return INSTRUCTION SE T REF ERENCE, A-M THEN #GP(0) ; FI; EIP ← Pop(); EIP ← EIP AND 0000FFFFH; CS ← Pop(); (* 16-bit pop *) EFLAGS[15:0] ← Pop(); (* IOPL .
Vol. 2A 3-495 INSTRUCTION SE T REF ERENCE, A-M IRET/IRETD—Interrupt Return IF EIP is not within code segment limit THEN #GP(0); FI; END; PROTECTED-MODE-RETUR N: (* PE = 1 *) IF return code segm ent .
3-496 Vol. 2A IRET/IRETD—Interrupt Return INSTRUCTION SE T REF ERENCE, A-M EFLAGS(IOPL) ← tempEFLAGS; IF OperandSiz e = 32 or OperandSize = 64 THEN EFLAGS (VIF, VIP) ← tempEFLAGS; FI; FI; END; R.
Vol. 2A 3-497 INSTRUCTION SE T REF ERENCE, A-M IRET/IRETD—Interrupt Return IF CPL = 0 THEN EFLAGS(IOPL) ← tempEFLAGS; IF OperandS ize = 32 THEN EFLAGS(VM, VIF, VIP) ← tempEFLAGS; FI; IF OperandS.
3-498 Vol. 2A IRET/IRETD—Interrupt Return INSTRUCTION SE T REF ERENCE, A-M Flags A ffected All the flags and fields in the EFLAGS regi ster are potentially modified, depending on the mode of operation of the processor .
Vol. 2A 3-499 INSTRUCTION SE T REF ERENCE, A-M IRET/IRETD—Interrupt Return Virtual-8086 Mode Excep tions #GP(0) If the return instruction pointer is not within the return code segment limit. IF IOPL not equal to 3. #PF(fault -code) If a page fault occurs.
3-500 Vol. 2A IRET/IRETD—Interrupt Return INSTRUCTION SE T REF ERENCE, A-M If the stack segment selector RPL is not equal to the RPL of the return code segment selector . #SS(0) If an attempt to pop a value off the stack violates the SS limit. If an attempt to pop a value off the stack causes a non-canonical address to be referenced.
Vol. 2A 3-501 INSTRUCTION SE T REF ERENCE, A-M Jcc—Jump if Condition Is Met J cc —Jump if Condition Is Met Opcode Instruction 64-Bit Mode Compat/ Leg Mode Description 77 cb JA rel 8 Valid V alid Jump sh ort if abov e (CF=0 a nd ZF=0). 73 cb JAE re l8 Va lid Valid Jump short if above or equal (CF=0).
3-502 Vol. 2A Jcc—Jump if Condition Is Met INSTRUCTION SE T REF ERENCE, A-M 75 cb JNZ rel 8 V alid V alid Jump short if not z ero (ZF=0). 70 cb JO rel 8 Val id Vali d J um p sh or t if over flow (O F=1 ). 7A cb JP re l8 Va lid Valid Jump short if parity (PF=1).
Vol. 2A 3-503 INSTRUCTION SE T REF ERENCE, A-M Jcc—Jump if Condition Is Met 0F 8C cw JL rel 16 N.S. V alid Jump near if less (SF ≠ OF). No t supported in 64-bit mode . 0F 8C cd JL rel 32 Va lid Va lid Jump near if les s (SF ≠ OF). 0F 8E cw JLE rel1 6 N.
3-504 Vol. 2A Jcc—Jump if Condition Is Met INSTRUCTION SE T REF ERENCE, A-M 0F 8C cd JNGE rel 32 Valid V alid Jump near if not gr eater or equal (SF ≠ OF). 0F 8D cw JNL rel 16 N .S. Valid Jum p near if not less (SF=OF). Not supported i n 64-bit mode.
Vol. 2A 3-505 INSTRUCTION SE T REF ERENCE, A-M Jcc—Jump if Condition Is Met Description Checks the state of one or more of the status flags in the EFLAGS register (CF , OF , PF , SF , and ZF) and, if the flags are in the spec ified state (condition), performs a jump to the target instruction specified by the destination operand.
3-506 Vol. 2A Jcc—Jump if Condition Is Met INSTRUCTION SE T REF ERENCE, A-M checked is determined by the address-size attribute. These instructions are useful when used at the beginning of a loop that terminates with a conditional loop instruc- tion (such as LOOPNE).
Vol. 2A 3-507 INSTRUCTION SE T REF ERENCE, A-M Jcc—Jump if Condition Is Met Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Ex cep tions #GP(0) If the memory address is in a non-canonical form. #UD If the LOCK prefix is used.
3-508 Vol. 2A JMP—Jump INSTRUCTION SE T REF ERENCE, A-M JMP—Jump Descripti on T r ansfers progr am control to a different point in the instruction stream without recording return information. The destinat ion (target) oper and specifies the address of the instruction being jumped to.
Vol. 2A 3-509 INSTRUCTION SE T REF ERENCE, A-M JMP—Jump • Short jump—A near jump where the jump range is limited to –128 to + 127 from the current EIP v alue. • F ar jump— A jump to an instruction located in a different segment than the current code segment but at the same privilege le vel, sometimes referred to as an intersegment jump.
3-510 Vol. 2A JMP—Jump INSTRUCTION SE T REF ERENCE, A-M • A task switch. (The JMP instruction cannot be used to perform inter-privilege-level far jumps.) In protected mode, the processor always uses the segment selector part of the far address to access the corresponding descriptor in the GD T or LDT .
Vol. 2A 3-511 INSTRUCTION SE T REF ERENCE, A-M JMP—Jump and save the previous task link information, allowing a return to the calling task with an IRET instruction.
3-512 Vol. 2A JMP—Jump INSTRUCTION SE T REF ERENCE, A-M FI; IF far jump and (PE = 0 or (PE = 1 AND VM = 1)) (* Real-address or virtual-8086 mode *) THEN tempEIP ← DEST(Offset); (* DEST is ptr16:32.
Vol. 2A 3-513 INSTRUCTION SE T REF ERENCE, A-M JMP—Jump THEN GP(new code se gment selector); FI; IF DPL > CPL THEN #GP(segment selector); FI; IF segment not presen t THEN #NP(segment selecto r); FI; tempEIP ← DEST(Offset); IF OperandS ize = 16 THEN tempEIP ← tempEIP AND 0000FFFFH; FI; IF (IA32_EFER.
3-514 Vol. 2A JMP—Jump INSTRUCTION SE T REF ERENCE, A-M THEN #GP(0) ; FI; IF call gate code-segment selector index outside descriptor table li mits THEN #GP(code segment selector); FI; Read code seg.
Vol. 2A 3-515 INSTRUCTION SE T REF ERENCE, A-M JMP—Jump or TSS DPL < TSS segment-selector RPL or TSS descri ptor indicates TSS not available THEN #GP(TSS s elector); FI; IF TSS is not prese nt TH.
3-516 Vol. 2A JMP—Jump INSTRUCTION SE T REF ERENCE, A-M If the segment selector for a TSS has its local/global bit set for local. If a TSS segment descriptor specifies that the TSS is busy or not available. #SS(0) If a memory oper and effective add ress is outside the S S segment limit.
Vol. 2A 3-517 INSTRUCTION SE T REF ERENCE, A-M JMP—Jump If target offset in destination operand is non-canonical. If target offset in destination operand is beyond the new code segment limit. If the segment selector in the destination oper and is NULL.
3-518 Vol. 2A LAHF—Load Status Flags into AH Register INSTRUCTION SE T REF ERENCE, A-M LAHF—Load S tatus Flags into AH R egister Descripti on This instruction executes as described above in compatibilit y mode and legacy mode. It is valid in 64-bit mode only if CPUID.
Vol. 2A 3-519 INSTRUCTION SE T REF ERENCE, A-M LAHF—Load Status Flags into AH Register 64-Bit Mode Ex cep tions #UD If CPUID.80000001H:ECX.LAHF-SAHF[bit 0] = 0.
3-520 Vol. 2A LAR—Load Access Rights Byte INSTRUCTION SE T REF ERENCE, A-M LAR—Load Acc ess Rights Byte Descripti on Loads the access rights from the segment de scriptor specified by the second operand (source operand) into the first operand (destination oper and) and sets the ZF flag in the flag register .
Vol. 2A 3-521 INSTRUCTION SE T REF ERENCE, A-M LAR—Load Access Rights Byte • If the segment is not a conforming code segment, it checks that the specified segment descriptor is visible at the CPL (that is, if the CPL and the RPL of the segment selector are less than or equal to th e DPL of the segment selector).
3-522 Vol. 2A LAR—Load Access Rights Byte INSTRUCTION SE T REF ERENCE, A-M ZF = 0; ELSE IF SegmentDescriptor(Type) ≠ conforming code segment and (CPL > DPL) or (RPL > DPL) or segment type is.
Vol. 2A 3-523 INSTRUCTION SE T REF ERENCE, A-M LAR—Load Access Rights Byte Virtual-8086 Mo de Ex ceptions #UD The LAR instruction cannot be executed in virtual-8086 mode.
3-524 Vol. 2A LDDQU—Load Unaligned Integer 128 Bits INSTRUCTION SE T REF ERENCE, A-M LDDQU—Load Unaligned In teger 128 Bits Descripti on The instruction is functionally similar to MOVDQU xmm, m128 for loading from memory .
Vol. 2A 3-525 INSTRUCTION SE T REF ERENCE, A-M LDDQU—Load Unaligned Integer 128 Bits Intel C/C + + Compiler Intrinsi c Equivalent LDDQU __m128i _mm_lddqu_si128(__m128i const *p ) Numeric Ex ceptions None. Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-526 Vol. 2A LDDQU—Load Unaligned Integer 128 Bits INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-527 INSTRUCTION SE T REF ERENCE, A-M LDMXCSR—Load MXCSR Register LDMX CSR—Load MX CSR Register Description Loads the source operand into the MXCSR control/status register .
3-528 Vol. 2A LDMXCSR—Load MXCSR Register INSTRUCTION SE T REF ERENCE, A-M If CPUID.01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-529 INSTRUCTION SE T REF ERENCE, A-M LDS/LES/LFS/LGS/LSS—Load Far Pointer LDS/LES/LFS/L GS/LSS—Load F ar Poin ter Description Loads a far pointer (segment selector and offset) from the second operand (source operand) into a segment register and the first operand (destination oper and).
3-530 Vol. 2A LDS/LES/LFS/LGS/LSS—Load Far Pointer INSTRUCTION SE T REF ERENCE, A-M If one of these instructions is executed in protected mode, additional information from the segment descriptor pointed to by the segment se lector in the source operand is loaded in the hidden part of the selected segment register .
Vol. 2A 3-531 INSTRUCTION SE T REF ERENCE, A-M LDS/LES/LFS/LGS/LSS—Load Far Pointer FI; SegmentRegister ← SegmentSelector( SRC) ; SegmentRegister ← SegmentDescr iptor([SRC]); FI; ELSE IF FS, or .
3-532 Vol. 2A LDS/LES/LFS/LGS/LSS—Load Far Pointer INSTRUCTION SE T REF ERENCE, A-M FI; DEST ← Offset(SRC); Real-Address or Virtual-8 086 Mode SegmentRegister ← Segmen tSelector(SRC); FI; DEST ← Offset(SRC); Flags A ffected None. Pro tected Mode Ex ceptions #UD If source operand is not a memory location.
Vol. 2A 3-533 INSTRUCTION SE T REF ERENCE, A-M LDS/LES/LFS/LGS/LSS—Load Far Pointer #SS If a memory operand effective address is outside the SS segment limit. #UD If source operand is not a memory location. If the LOCK prefix is used. Virtual-8086 Mode Excep tions #UD If source operand is not a memory location.
3-534 Vol. 2A LDS/LES/LFS/LGS/LSS—Load Far Pointer INSTRUCTION SE T REF ERENCE, A-M #NP(selector) I f FS, or GS register is being loaded with a non-NULL segment selector and the segment is marked not present.
Vol. 2A 3-535 INSTRUCTION SE T REF ERENCE, A-M LEA—Load Effective Address LEA—L oad Effective Addr ess Description Computes the effective address of the se cond oper and (the source oper and) and stores it in the first oper and (destination operand).
3-536 Vol. 2A LEA—Load Effective Address INSTRUCTION SE T REF ERENCE, A-M Operat ion IF OperandS ize = 16 and AddressS ize = 16 THEN DEST ← EffectiveAddress(SRC ); (* 16-bit address *) ELSE IF Ope.
Vol. 2A 3-537 INSTRUCTION SE T REF ERENCE, A-M LEA—Load Effective Address DEST ← temp[0:1 5]; (* 16-bit address *) FI; ELSE IF OperandSize = 3 2 and AddressSize = 64 THEN temp ← EffectiveAddr es.
3-538 Vol. 2A LEAVE—High Level Procedure Exit INSTRUCTION SE T REF ERENCE, A-M LEA V E—High Lev el Pr ocedure Exit Descripti on Releases the stack fr ame set up by an earlier ENTER instruction.
Vol. 2A 3-539 INSTRUCTION SE T REF ERENCE, A-M LEAVE—High Level Procedure Exit Flags A ffected None. Pr otected Mode Ex ceptions #SS(0) If the EBP register points to a location that is not within the limits of the current stack segment. #PF(fault -code) If a page fault occurs.
3-540 Vol. 2A LFENCE—Load Fence INSTRUCTION SE T REF ERENCE, A-M LFENCE—Load F ence Descripti on Performs a serializing oper ation on all lo ad-from-memory instructions that were issued prior the LFENCE instruction.
Vol. 2A 3-541 INSTRUCTION SE T REF ERENCE, A-M LGDT/LIDT—Load Global/Interrupt Descriptor Table Register L GDT /LIDT—L oad Global/Interrup t Descript or T able Register Description Loads the values in the source operand into the global descriptor table register (GDTR) or the interrupt descriptor table register (ID TR).
3-542 Vol. 2A LGDT/LIDT—Load Global/Interru pt Descriptor Table Register INSTRUCTION SE T REF ERENCE, A-M IDTR(Limit) ← SRC[0:15]; IDTR(Base) ← SRC[16:47]; FI; ELSE IF 64-bit Opera nd Si ze (* I.
Vol. 2A 3-543 INSTRUCTION SE T REF ERENCE, A-M LGDT/LIDT—Load Global/Interrupt Descriptor Table Register Real-Address Mode Ex ceptions #UD If source operand is not a memory location. If the LOCK prefix is used. #GP If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit.
3-544 Vol. 2A LLDT—L oad Local Descriptor Table Register INSTRUCTION SE T REF ERENCE, A-M LLD T—Load L ocal Descriptor T able R egister Descripti on Loads the source operand into the segment selector field of the local descriptor table register (LDTR).
Vol. 2A 3-545 INSTRUCTION SE T REF ERENCE, A-M LLDT—Load Local Descriptor Table Register ELSE LDTR ← INVALID FI; Flags A ffected None. Pr otected Mode Ex ceptions #GP(0) If the current privilege level is not 0. If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit.
3-546 Vol. 2A LLDT—L oad Local Descriptor Table Register INSTRUCTION SE T REF ERENCE, A-M #PF(fault-code) If a page fault occurs. #UD If the LOCK prefix is used.
Vol. 2A 3-547 INSTRUCTION SE T REF ERENCE, A-M LMSW—Load Machine Status Word LMSW—L oad Machine S tatus Wor d Description Loads the source operand into the mach ine st atus word, bits 0 through 15 of register CR0. The source operand can be a 16-bit general-purpose register or a memory loca- tion.
3-548 Vol. 2A LMSW—Load Machine Status Word INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If the current privilege level is not 0. If a memory oper and effective address is outside the CS , DS, ES, FS, or GS segment limit. If the DS, ES, FS , or GS register is used to access memory and it contains a NULL segment selector .
Vol. 2A 3-549 INSTRUCTION SE T REF ERENCE, A-M LOCK—Assert LOCK# Signal Prefix LOCK —Assert L OCK# Signal Prefix Description Causes the processor’s LOCK# signal to be asserted during execution of the accom- panying instruction (turns the instruction in to an atomic instruction).
3-550 Vol. 2A LOCK—Assert LOCK# Signal Prefix INSTRUCTION SE T REF ERENCE, A-M Operat ion AssertLOCK#(Duration OfA ccompaningI nstruction); Flags A ffected None.
Vol. 2A 3-551 INSTRUCTION SE T REF ERENCE, A-M LODS/LODS B/LODSW/LOD SD/LODSQ—Loa d String L ODS/L ODSB/L ODSW/L ODSD/LODSQ—L oad S tring Description Loads a byte, word, or doubleword from th e source operand into the AL, AX, or EAX register , respectively .
3-552 Vol. 2A LODS/LODSB/LODSW/LODSD/LODSQ—Load String INSTRUCTION SE T REF ERENCE, A-M correct location . The location is always specifie d by the DS:(E)SI registers, which must be loaded correctly before the load string instruction is executed.
Vol. 2A 3-553 INSTRUCTION SE T REF ERENCE, A-M LODS/LODS B/LODSW/LOD SD/LODSQ—Loa d String FI; FI; ELSE IF RAX ← SRC; (* Quad wo rd load *) THEN IF DF = 0 THEN (R)SI ← (R)SI + 8; ELSE (R)SI ← (R)SI – 8; FI; FI; FI; Flags A ffected None.
3-554 Vol. 2A LODS/LODSB/LODSW/LODSD/LODSQ—Load String INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-555 INSTRUCTION SE T REF ERENCE, A-M LOOP/LOOPcc—Loop According to ECX Counter L OOP/L OOP cc —Loop Ac cording to ECX Coun ter Description Performs a loop oper ation using the RCX, ECX or CX register as a counter (depending on whether address size is 64 bits, 32 bits, or 16 bits).
3-556 Vol. 2A LOOP/LOOPcc—Loop According to ECX Counter INSTRUCTION SE T REF ERENCE, A-M IF (Instruction ← LOOPE) or (Instr uction ← LOOPZ) THEN IF (ZF = 1) and (Count ≠ 0) THEN BranchCon d .
Vol. 2A 3-557 INSTRUCTION SE T REF ERENCE, A-M LOOP/LOOPcc—Loop According to ECX Counter Pr otected Mode Ex ceptions #GP(0) If the offset being jumped to is beyond the limits of the CS segment.
3-558 Vol. 2A LSL—Load Segment Limit INSTRUCTION SE T REF ERENCE, A-M LSL —Load Segmen t Limit Descripti on Loads the unscrambled segment limit from the segment descriptor specified with the second oper and (source oper and) into the first oper and (destination operand) and sets the ZF flag in the EFLAGS register .
Vol. 2A 3-559 INSTRUCTION SE T REF ERENCE, A-M LSL—Load Segment Limit • Checks that the descriptor type is valid for this instruction. All code and data segment descriptors are v alid for (can be accessed with) the LSL instruction. The valid special segment and gate descriptor types are given in the following table.
3-560 Vol. 2A LSL—Load Segment Limit INSTRUCTION SE T REF ERENCE, A-M Read segment descriptor; IF SegmentDescriptor(Type) ≠ conforming code segment and (CPL > DPL) OR (RPL > DPL) or Segment .
Vol. 2A 3-561 INSTRUCTION SE T REF ERENCE, A-M LSL—Load Segment Limit Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If the memory operand effective address referencing the SS segment is in a non-canonical form.
3-562 Vol. 2A LTR—Load Task Register INSTRUCTION SE T REF ERENCE, A-M L TR—L oad T ask Register Descripti on Loads the source operand into the segment selector field of the task register . Th e source operand (a general-purpose register or a memory location) contains a segment selector that points to a task state segment (TSS).
Vol. 2A 3-563 INSTRUCTION SE T REF ERENCE, A-M LTR—Load Task Register Flags A ffected None. Pr otected Mode Ex ceptions #GP(0) If the current privilege level is not 0. If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit.
3-564 Vol. 2A LTR—Load Task Register INSTRUCTION SE T REF ERENCE, A-M #NP(selector) I f the TSS is marked not present. #PF(fault-code) If a page fault occurs.
Vol. 2A 3-565 INSTRUCTION SE T REF ERENCE, A-M MASKMOVDQU—Store Selected Bytes of Double Quadword MASKMO VDQU—S tore Se lected Bytes of Double Quadw ord Description Stores selected bytes from the source operand (first oper and) into an 128-bit memory location.
3-566 Vol. 2A MASKMOVDQU—Store Selected Bytes of D ouble Quadword INSTRUCTION SE T REF ERENCE, A-M In 64-bit mode, use of the REX.R prefix perm its this instruction to access additional registers (XMM8- XMM15).
Vol. 2A 3-567 INSTRUCTION SE T REF ERENCE, A-M MASKMOVDQU—Store Selected Bytes of Double Quadword Virtual-8086 Mode Excep tions Same exceptions as in real address mode. #PF(fault-code) F or a page fault (implementation specific). #UD If the LOCK prefix is used.
3-568 Vol. 2A MASKMO VQ—Store Selected Bytes of Qu adword INSTRUCTION SE T REF ERENCE, A-M MASKMOV Q—S tore Selected Bytes o f Quadwor d Descripti on Stores selected bytes from the source operand (first oper and) into a 64-bit memory location. The mask operand (second operand) selects which bytes from the source operand are written to mem ory .
Vol. 2A 3-569 INSTRUCTION SE T REF ERENCE, A-M MASKMOVQ—Store Select ed Bytes of Quadword The MASKMOVQ instruction can be used to improv e performance for algorithms that need to merge data on a byte-by-byte basi s.
3-570 Vol. 2A MASKMO VQ—Store Selected Bytes of Qu adword INSTRUCTION SE T REF ERENCE, A-M #MF If there is a pending FPU exception. #UD I f CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. Virtual-8086 Mode E xc eptions Same exceptions as in real address mode.
Vol. 2A 3-571 INSTRUCTION SE T REF ERENCE, A-M MAXPD—Return Maximu m Packed Double -Precision Floating-Point Value s MAXPD—Re turn Maximum Pack ed Double-Precision Floating-Poin t Va l u e s Descr.
3-572 Vol. 2A MAXPD—Return Maximum Packed Double -P recision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M ELSE SRC[127:64]; FI; FI; Intel C/C + + Compiler Intrinsic Equivalent MAXPD __m128d _mm_max_pd(__ m128d a, __m128d b) SIMD Floating-Poin t Ex ceptions Invalid (including QNaN source operand), Denormal.
Vol. 2A 3-573 INSTRUCTION SE T REF ERENCE, A-M MAXPD—Return Maximu m Packed Double -Precision Floating-Point Value s Virtual-8086 Mode Excep tions Same exceptions as in real address mode. #PF(fault -code) For a page fault. Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-574 Vol. 2A MAXPS—Return Maximum Packed Single-Precision Floating-P oint Values INSTRUCTION SE T REF ERENCE, A-M MAXPS—Re turn Maximum Pack ed Single-Precision Floating-Poin t Va l u e s Descrip.
Vol. 2A 3-575 INSTRUCTION SE T REF ERENCE, A-M MAXPS—Return Maximum Packed Single-Precis ion Floating-Point Values THEN DEST[127:96]; ELSE SRC[127:96]; FI; FI; Intel C/C + + Compiler Intrinsi c Equivalent MAXPS __m128d _mm_max_ps(__m1 28d a, __m128d b) SIMD Floating-Point Ex ceptions Inv alid (including QNaN source oper and), Denormal.
3-576 Vol. 2A MAXPS—Return Maximum Packed Single-Precision Floating-P oint Values INSTRUCTION SE T REF ERENCE, A-M If CPUID.01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. Virtual-8086 Mode E xc eptions Same exceptions as in real address mode. #PF(fault-code) F or a page fault.
Vol. 2A 3-577 INSTRUCTION SE T REF ERENCE, A-M MAXSD—Return Maximum Scalar Double-Precision Floating-Point Value MAXSD—Re turn Maximum Scalar Do uble-Precision Floating-Poin t Va l u e Description.
3-578 Vol. 2A MAXSD—Return Maximum Scalar Double-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M Intel C/C + + Compiler Intrinsic Equivalent MAXSD __m128d _mm_max_sd(__m128d a, _ _m128d b) SIMD Floating-Poin t Ex ceptions Invalid (including QNaN source operand), Denormal.
Vol. 2A 3-579 INSTRUCTION SE T REF ERENCE, A-M MAXSD—Return Maximum Scalar Double-Precision Floating-Point Value #PF(fault -code) For a page fault. #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made. Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-580 Vol. 2A MAXSS—Return Maximum Scalar Single-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M MAXSS—R eturn Maximum Scalar Single -Precision Floating-P oint V alue Descripti on .
Vol. 2A 3-581 INSTRUCTION SE T REF ERENCE, A-M MAXSS—Return Maximum Scalar Single-P recision Floating-Point Value SIMD Floating-Point Ex ceptions Inv alid (including QNaN source oper and), Denormal. Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-582 Vol. 2A MAXSS—Return Maximum Scalar Single-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc eptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-583 INSTRUCTION SE T REF ERENCE, A-M MFENCE—Memory Fence MFENCE—Memory F ence Description Performs a serializing operation on a ll load-from-memory and store-to-memory instructions that were issued prior the MFEN CE ins truction.
3-584 Vol. 2A MINPD—Return Minimum Packed Double-Precision Floating-P oint Values INSTRUCTION SE T REF ERENCE, A-M MINPD—R eturn Minimum P ack ed Double-Precision Floating-Poin t Va l u e s Descri.
Vol. 2A 3-585 INSTRUCTION SE T REF ERENCE, A-M MINPD—Return Minimum Packed Double-Precision Floating-Point Values THEN DEST[127:64] ELSE SRC[127:64]; FI; FI; Intel C/C + + Compiler Intrinsi c Equivalent MINPD __m128d _mm_min_pd(__m128d a , __m128d b) SIMD Floating-Point Ex ceptions Inv alid (including QNaN source oper and), Denormal.
3-586 Vol. 2A MINPD—Return Minimum Packed Double-Precision Floating-P oint Values INSTRUCTION SE T REF ERENCE, A-M If CPUID .01H:E DX.SSE 2[bit 26] = 0. If the LOCK prefix is used. Virtual-8086 Mode E xc eptions Same exceptions as in real address mode.
Vol. 2A 3-587 INSTRUCTION SE T REF ERENCE, A-M MINPS—Return Minimum Packed Single-Precisi on Floating-Point Values MINPS—Re turn Minimum Pack ed Single-Precision Floating-P oint Va l u e s Descrip.
3-588 Vol. 2A MINPS—Return Minimum Packed Single-P recision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M THEN DEST[127:96] ELSE SRC[127:96]; FI; FI; Intel C/C + + Compiler Intrinsic Equivalent MINPS __m128d _mm_min_ps(__m128d a, __ m128d b) SIMD Floating-Poin t Ex ceptions Invalid (including QNaN source operand), Denormal.
Vol. 2A 3-589 INSTRUCTION SE T REF ERENCE, A-M MINPS—Return Minimum Packed Single-Precisi on Floating-Point Values If CPUID .01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. Virtual-8086 Mode Excep tions Same exceptions as in real address mode. #PF(fault -code) For a page fault.
3-590 Vol. 2A MINSD—Return Minimum Scalar Double-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M MINSD—Re turn Minimum Scalar Double -Pr ecision Floating-Poin t V alue Descripti on.
Vol. 2A 3-591 INSTRUCTION SE T REF ERENCE, A-M MINSD—Return Minimum Scalar Double-Prec ision Floating-Point Value SIMD Floating-Point Ex ceptions Inv alid (including QNaN source oper and), Denormal. Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-592 Vol. 2A MINSD—Return Minimum Scalar Double-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc eptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form.
Vol. 2A 3-593 INSTRUCTION SE T REF ERENCE, A-M MINSS—Return Minimum Scalar Single-Precision Float ing-Point Value MINSS—Re turn Minimum Scalar Single -Pr ecision Floating-Point V alue Description .
3-594 Vol. 2A MINSS—Return Minimum Scalar Single-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M SIMD Floating-Poin t Ex ceptions Invalid (including QNaN source operand), Denormal. Pro tected Mode Ex ceptions #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents.
Vol. 2A 3-595 INSTRUCTION SE T REF ERENCE, A-M MINSS—Return Minimum Scalar Single-Precision Float ing-Point Value Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form.
3-596 Vol. 2A MONITO R—Set Up Monitor Address INSTRUCTION SE T REF ERENCE, A-M MONIT OR—Set Up Monitor Addr ess Descripti on The MONITOR instruction arms address monitoring hardw are using an address spec- ified in EAX (the address range that the monitoring hardware checks for store opera- tions can be determined by using CPUID).
Vol. 2A 3-597 INSTRUCTION SE T REF ERENCE, A-M MONITOR—Set Up Monitor Address Operation MONITOR sets up an address r ange for the monitor hardware using the content of EAX as an effective address and puts the monitor hardware in armed state. Alw ays use memory of the write-back caching type .
3-598 Vol. 2A MONITO R—Set Up Monitor Address INSTRUCTION SE T REF ERENCE, A-M 64-Bit Mode Exc eptions #GP(0) If the linear address of the operand in the CS, DS, ES, FS , or GS segment is in a non-canonical form. If RCX ← 0. #SS(0) If the linear address of the operand in the SS segment is in a non-canonical form.
Vol. 2A 3-599 INSTRUCTION SE T REF ERENCE, A-M MOV—Move MO V—Mov e Opcode Instruction 64-Bit Mode Compat/ Leg Mode Description 88 / r MOV r/m8,r8 Va l i d Va l i d M o v e r8 to r/m8. REX + 88 / r MOV r/m8 ***, r8 *** Va l i d N . E . M o ve r8 to r/m8.
3-600 Vol. 2A MOV—Move INSTRUCTION SE T REF ERENCE, A-M Descripti on Copies the second operand (source operand) to the first operand (destination operand ).
Vol. 2A 3-601 INSTRUCTION SE T REF ERENCE, A-M MOV—Move below). The segment descriptor data is obtained from the GD T or LD T entry for the specified segment selector . A NULL segment selector (values 0000-0003) can be load ed into the DS, ES, FS , and GS registers without causing a protection exception.
3-602 Vol. 2A MOV—Move INSTRUCTION SE T REF ERENCE, A-M Loading a segment register while in protec ted mode results in special checks and actions, as described in the following lis ting. These checks are performed on the segment selector and the segment descriptor to which it points.
Vol. 2A 3-603 INSTRUCTION SE T REF ERENCE, A-M MOV—Move Pr otected Mode Ex ceptions #GP(0) If attempt is made to load S S register with NULL segment selector . If the destination operand is in a non-writable segment. If a memory operand effective address is outside the CS, DS , ES, FS, or GS segment limit.
3-604 Vol. 2A MOV—Move INSTRUCTION SE T REF ERENCE, A-M #SS(0) If a memory oper and effective add ress is outside the S S segment limit. #PF(fault-code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory reference is made.
Vol. 2A 3-605 INSTRUCTION SE T REF ERENCE, A-M MOV—Move to/from Control Registers MO V—Mov e to/fr om Contr ol R egisters Description Moves the contents of a control regis ter (CR0, CR2, CR3, CR4, or CR8) to a general- purpose register or the contents of a gener al purpose register to a control register .
3-606 Vol. 2A MOV—Move to/from Control Registers INSTRUCTION SE T REF ERENCE, A-M and CR3 remain clear after any load of those registers; attempts to set them ha ve no impact. On Pentium 4, Intel X eon and P6 fa mily processors, CR0.ET remains set after any load of CR0; attempts to clear this bit hav e no impact.
Vol. 2A 3-607 INSTRUCTION SE T REF ERENCE, A-M MOV—Move to/from Control Registers If an attempt is made to write invalid bit combinations in CR0 (such as setting the PG flag to 1 wh en the PE flag is set to 0, or setting the CD flag to 0 when the NW flag is set to 1).
3-608 Vol. 2A MOV—Move to/from Debug Registers INSTRUCTION SE T REF ERENCE, A-M MO V—Mov e to/fr om Debug Regis ters Descripti on Moves the contents of a debug register (DR0, DR1, DR2, DR3, DR4, DR5, DR6, or DR7) to a general-purpose register or vice versa.
Vol. 2A 3-609 INSTRUCTION SE T REF ERENCE, A-M MOV—Move to/from Debug Registers Flags A ffected The OF , SF , ZF , AF , PF , and CF flag s are undefined. Pr otected Mode Ex ceptions #GP(0) If the current privilege level is not 0. #UD If CR4.DE[bit 3] = 1 (debug extensions) and a MOV instruction is executed involving DR4 or DR5.
3-610 Vol. 2A MOVAPD—Move Aligned Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M MO V APD—Mov e Aligned Pack ed Double-Precision Floating-Poin t Va l u e s Descript.
Vol. 2A 3-611 INSTRUCTION SE T REF ERENCE, A-M MOVAPD—Move Aligned Packed Double-Prec ision Floating-Point Values Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments. If a memory operand is not aligned on a 16-byte boundary , regardless of segment.
3-612 Vol. 2A MOVAPD—Move Aligned Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD I f CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0.
Vol. 2A 3-613 INSTRUCTION SE T REF ERENCE, A-M MOVAPS—Move Aligned Packed Single-Precision Floating-Point Valu es MO V APS—Mov e Aligned Pack ed Single-Precision Floating-Poin t V alues Descriptio.
3-614 Vol. 2A MOVAPS—Move Aligned Packed Single-Precision Floating-P oint Values INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents. If a memory operand is not aligned on a 16-byte boundary , regardless of segment.
Vol. 2A 3-615 INSTRUCTION SE T REF ERENCE, A-M MOVAPS—Move Aligned Packed Single-Precision Floating-Point Valu es #UD If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0 .
3-616 Vol. 2A MOVD/MOVQ—Move Doubleword/Move Quadword INSTRUCTION SE T REF ERENCE, A-M MO VD/MOV Q—Mo ve Doublew ord/Mo ve Quadw ord Descripti on Copies a doubleword from the source oper and (second operand) to the destination operand (first oper and).
Vol. 2A 3-617 INSTRUCTION SE T REF ERENCE, A-M MOVD/MOVQ—Move Doubl eword/Move Quadword Operation MOVD instruction when destination oper and is MMX technology r egister: DEST[31: 0] ← SRC; DEST[63.
3-618 Vol. 2A MOVD/MOVQ—Move Doubleword/Move Quadword INSTRUCTION SE T REF ERENCE, A-M #UD If CR0 .EM[bit 2] = 1. 128-bit operations will generate #UD only if CR4.
Vol. 2A 3-619 INSTRUCTION SE T REF ERENCE, A-M MOVD/MOVQ—Move Doubl eword/Move Quadword #UD If CR0.EM[bit 2] = 1. (XMM register operations only ) if CR4.OSFXSR[bit 9] = 0. (XMM register operations only) if CPUID.01H:EDX.S SE2[bit 26] = 0. If the LOCK prefix is used.
3-620 Vol. 2A MOVDDUP—Move One Double-FP and Duplicate INSTRUCTION SE T REF ERENCE, A-M MO VDDUP—Mov e One Double-FP and Duplicate Descripti on The linear address corresponds to the addre ss of the least-significant byte of the referenced memory data.
Vol. 2A 3-621 INSTRUCTION SE T REF ERENCE, A-M MOVDDUP—Move One Double-FP and Duplicate xmm1[127:6 4] = m64; ELSE (* Move in struction *) xmm1[63:0] = xmm2[63:0]; xmm1[127:64] = xmm2[63:0]; FI; Inte.
3-622 Vol. 2A MOVDDUP—Move One Double-FP and Duplicate INSTRUCTION SE T REF ERENCE, A-M Virtual 8086 Mode Ex ceptions GP(0) If any part of the operand would lie outside of the effe ctive address space from 0 to 0FFFFH. #NM If CR0.TS[bit 3] = 1. #UD I f CR0.
Vol. 2A 3-623 INSTRUCTION SE T REF ERENCE, A-M MOVDQA—Move Aligned Double Quadword MO VDQA—Mo ve Aligned Double Quadwor d Description Moves a double quadword from the source oper and (second operand) to the destina- tion operand (first operan d).
3-624 Vol. 2A MOVDQA—Move Aligned Double Quadwo rd INSTRUCTION SE T REF ERENCE, A-M #SS(0) If a memory oper and effective add ress is outside the S S segment limit. #NM If CR0.TS[bit 3] = 1. #UD If CR0 .EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.
Vol. 2A 3-625 INSTRUCTION SE T REF ERENCE, A-M MOVDQU—Move Unaligned Double Quadword MO VDQU—Mov e Unaligned Double Quadwor d Description Moves a double quadword from the source oper and (second operand) to the destina- tion operand (first operan d).
3-626 Vol. 2A MOVDQU—Move Unaligned Double Quadword INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #AC(0) If alignment checking is enabled and an unaligned memory reference is made. #GP(0) If a memory operand effe ctive address is outside the CS, DS , ES, FS, or GS segment limit.
Vol. 2A 3-627 INSTRUCTION SE T REF ERENCE, A-M MOVDQU—Move Unaligned Double Quadword #UD If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .01H:EDX.
3-628 Vol. 2A MOVDQ2Q—Move Quadword from XMM to MMX Technology Register INSTRUCTION SE T REF ERENCE, A-M MO VDQ2Q—Mov e Quadwor d fro m XMM to MMX T echnology R egister Descripti on Moves the low quadword from the source oper and (second operand) to the destina- tion operand (first oper and).
Vol. 2A 3-629 INSTRUCTION SE T REF ERENCE, A-M MOVDQ2Q—Move Quadword from XMM to MMX Technology Register Virtual-8086 Mode Excep tions Same exceptions as in protected mode. Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions Same exceptions as in protected mode.
3-630 Vol. 2A MOVHLPS— Move Packed Single-Precision Floating-Po int Values High to Low INSTRUCTION SE T REF ERENCE, A-M MO VHLPS— Mov e Pack ed Single-Precision Floating-Poin t V alues High to Low.
Vol. 2A 3-631 INSTRUCTION SE T REF ERENCE, A-M MOVHLPS— Move Packed Single-Precision Floating-Point Values High to Low Virtual 8086 M ode Ex ceptions Same exceptions as in protected mode. Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-632 Vol. 2A MOVHPD—Move High Packed Double-P recision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M MO VHPD—Mov e High Pack ed Double-Precision Floating-Poin t V alue Descripti on Moves a double-precision floating-point value from the source operand (second operand) to the destination operand (first oper and).
Vol. 2A 3-633 INSTRUCTION SE T REF ERENCE, A-M MOVHPD—Move High Packed Double-P recision Floating-Point Value Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments. #SS(0) For an illegal address in the SS segment.
3-634 Vol. 2A MOVHPD—Move High Packed Double-P recision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M If CPUID .01H:E DX.SSE 2[bit 26] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-635 INSTRUCTION SE T REF ERENCE, A-M MOVHPS—Move High Packed Single-Precision Floating-Point Values MO VHPS—Mov e High Pack ed Single-Precision Floating-Poin t V alues Description Moves two packed single-precision floating -point v alues from the source oper and (second operand) to the destination operan d (first operand).
3-636 Vol. 2A MOVHPS—Move High Packed Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #SS(0) For an illegal address in the SS segment. #PF(fault-code) F or a page fault. #NM If CR0.TS[bit 3] = 1. #UD If CR0 .EM[bit 2] = 1. If CR4.
Vol. 2A 3-637 INSTRUCTION SE T REF ERENCE, A-M MOVHPS—Move High Packed Single-Precision Floating-Point Values #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
3-638 Vol. 2A MOVLHPS—Move Packed Si ngle-Precision Floating-Point Values Low to High INSTRUCTION SE T REF ERENCE, A-M MO VLHPS—Mov e Pack ed Single-Precision Floating-P oint V alues Lo w to High .
Vol. 2A 3-639 INSTRUCTION SE T REF ERENCE, A-M MOVLHPS—Move Packed Single-Precision Floating-Point Values Low to High Compatibility Mode Ex ceptions Same exceptions as in protected mode.
3-640 Vol. 2A MOVLPD—Move Low Packed Double-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M MO VLPD—Mov e Lo w Pack ed Double-Precision Floating-Point V alue Descripti on Moves a double-precision floating-point value from the source operand (second operand) to the destination operand (first oper and).
Vol. 2A 3-641 INSTRUCTION SE T REF ERENCE, A-M MOVLPD—Move Low Packed Double-P recision Floating-Point Value #SS(0) For an illegal address in the SS segment. #PF(fault -code) For a page fault. #NM If CR0.TS[bit 3] = 1. #UD If CR0.EM[bit 2] = 1. If CR4.
3-642 Vol. 2A MOVLPS—Move Low Packed Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M MO VLPS—Mov e Lo w Pack ed Single-Precision Floating-Poin t V alues Descripti on Moves two pack ed single-precision floating-point values from the source operand (second operand) and the de stination operan d (first operand).
Vol. 2A 3-643 INSTRUCTION SE T REF ERENCE, A-M MOVLPS—Move Low Packed Single-Precision Floating-Point Values #SS(0) For an illegal address in the SS segment. #PF(fault -code) For a page fault. #NM If CR0.TS[bit 3] = 1. #UD If CR0.EM[bit 2] = 1. If CR4.
3-644 Vol. 2A MOVLPS—Move Low Packed Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-645 INSTRUCTION SE T REF ERENCE, A-M MOVMSKPD—Extract Packed Double-Precision Floating-Point Sign Mask MO VMSKPD—Extr act Pa ck ed Double-Precision Floating-P oint Sign Mask Description .
3-646 Vol. 2A MOVMSKPD—Extract Packed Double -Precision Floating-Point Sign Mask INSTRUCTION SE T REF ERENCE, A-M #UD I f CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .01H:E DX.SSE 2[bit 26] = 0. If the LOCK prefix is used. Real-Addr ess Mode Exc eptions Same exceptions as in protected mode.
Vol. 2A 3-647 INSTRUCTION SE T REF ERENCE, A-M MOVMSKPS—Extract Packed Single-Pre cision Floating-Point Sign Mask MO VMSKPS—Extr act Pa cked Single-Pr ecision Floating-Poin t Sign Mask Description.
3-648 Vol. 2A MOVMSKPS—Extract Packed Single-Pre cision Floating-P oint Sign Mask INSTRUCTION SE T REF ERENCE, A-M #UD I f CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. Real-Addr ess Mode Exc eptions Same exceptions as in protected mode.
Vol. 2A 3-649 INSTRUCTION SE T REF ERENCE, A-M MOVNTDQ—Store Double Quadword Using Non-Temporal Hint MO VNTDQ—S tore Double Quadw ord Using Non-T em poral Hin t Description Moves the double quadwo.
3-650 Vol. 2A MOVNTDQ—Store Double Quadword Using Non-Temporal H int INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents. If a memory operand is not aligned on a 16-byte boundary , regardless of segment.
Vol. 2A 3-651 INSTRUCTION SE T REF ERENCE, A-M MOVNTDQ—Store Double Quadword Using Non-Temporal Hint #UD If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0.
3-652 Vol. 2A MOVNTI—Store Doublewor d Using Non-Temporal Hint INSTRUCTION SE T REF ERENCE, A-M MO VNTI—S tore Doublew ord Using Non-T emporal Hin t Descripti on Moves the doubleword integer in th.
Vol. 2A 3-653 INSTRUCTION SE T REF ERENCE, A-M MOVNTI—Store Doubleword Using Non-Temporal Hint Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments. #SS(0) For an illegal address in the SS segment.
3-654 Vol. 2A MOVNTPD—Store Packed Double -Precision Fl oating-Point Values Using Non-Temporal Hint INSTRUCTION SE T REF ERENCE, A-M MO VNTPD—S tore P ack ed Double-Precision Floating-P oint V alu.
Vol. 2A 3-655 INSTRUCTION SE T REF ERENCE, A-M MOVNTPD—Store Packed Double-Precision Floating-Point Values Using Non-Temporal Hint Pr otected Mode Ex ceptions #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-656 Vol. 2A MOVNTPD—Store Packed Double -Precision Fl oating-Point Values Using Non-Temporal Hint INSTRUCTION SE T REF ERENCE, A-M #UD If CR0 .EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .01H:E DX.SSE 2[bit 26] = 0. If the LOCK prefix is used.
Vol. 2A 3-657 INSTRUCTION SE T REF ERENCE, A-M MOVNTPS—Store Packed Single -Precision Fl oating-Point Values Using Non-Temporal Hint MO VNTPS—S tore P ack ed Single-Precision Floating-P oint V alu.
3-658 Vol. 2A MOVNTPS—Store Packed Single-Precisio n Fl oating-Point Values Using Non-Temporal Hint INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents.
Vol. 2A 3-659 INSTRUCTION SE T REF ERENCE, A-M MOVNTPS—Store Packed Single -Precision Fl oating-Point Values Using Non-Temporal Hint #UD If CR0.EM[bit 2] = 1.
3-660 Vol. 2A MOVNTQ—Store of Quadword Using Non-Temporal Hint INSTRUCTION SE T REF ERENCE, A-M MO VNT Q—S tore o f Quadwor d Using Non-T emporal Hin t Descripti on Moves the quadword in the sourc.
Vol. 2A 3-661 INSTRUCTION SE T REF ERENCE, A-M MOVNTQ—Store of Quadword Using Non-Temporal Hint #SS(0) For an illegal address in the SS segment. #PF(fault -code) For a page fault. #NM If CR0.TS[bit 3] = 1. #MF If there is a pending x87 FPU exception.
3-662 Vol. 2A MOVNTQ—Store of Quadword Using Non-Temporal Hint INSTRUCTION SE T REF ERENCE, A-M #UD If CR0 .EM[bit 2] = 1. If CPUID.01H:EDX.SSE[bit 25] = 0. If the LOCK prefix is used. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-663 INSTRUCTION SE T REF ERENCE, A-M MOVQ—Move Quadword MO VQ—Mo ve Quadw ord Description Copies a quadword from the source oper and (second operand) to the destination operand (first oper and). The source and destination operands can be MMX tech- nology registers, XMM registers, or 64-bit memory locations.
3-664 Vol. 2A MOVQ—Move Quadwo rd INSTRUCTION SE T REF ERENCE, A-M DEST[127:64] ← 0000000000000000H; Flags A ffected None. SIMD Floating-Poin t Ex ceptions None. Pro tected Mode Ex ceptions #GP(0) If the destination operand is in a non-writable segment.
Vol. 2A 3-665 INSTRUCTION SE T REF ERENCE, A-M MOVQ—Move Quadword Virtual-8086 Mode Excep tions Same exceptions as in real address mode. #PF(fault -code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made.
3-666 Vol. 2A MOVQ2DQ—Move Quadword from MMX Technology to XMM Register INSTRUCTION SE T REF ERENCE, A-M MO VQ2DQ—Mo ve Quadwor d from MMX T echnology t o XMM Register Descripti on Moves the quadword from the source oper and (second operand) to the low quadword of the destination operand (first operand).
Vol. 2A 3-667 INSTRUCTION SE T REF ERENCE, A-M MOVQ2DQ—Move Quadword from MMX Technology to XMM Register Virtual-8086 Mode Excep tions Same exceptions as in protected mode. Compatibility Mode Ex ceptions Same exceptions as in protected mode. 64-Bit Mode Exc eptions Same exceptions as in protected mode.
3-668 Vol. 2A MOVS/MOVSB/MOVSW/MOVSD/MOVSQ—Move Data from String to String INSTRUCTION SE T REF ERENCE, A-M M OVS /M OVS B / MOV SW /M OV SD / MOV S Q— M ove D a t a f ro m S tring to S tring Des.
Vol. 2A 3-669 INSTRUCTION SE T REF ERENCE, A-M MOVS/MOVSB/MOVSW/MOVSD/MOVSQ—Move Data from Stri ng to String At the assembly -code level, two forms of th is instruction are allowed: the “explicit- operands” form and the “no-oper ands” form .
3-670 Vol. 2A MOVS/MOVSB/MOVSW/MOVSD/MOVSQ—Move Data from String to String INSTRUCTION SE T REF ERENCE, A-M (E)SI ← (E)SI – 1; (E)DI ← (E)DI – 1; FI; ELSE IF (Word move) THEN IF DF = 0 (E)SI.
Vol. 2A 3-671 INSTRUCTION SE T REF ERENCE, A-M MOVS/MOVSB/MOVSW/MOVSD/MOVSQ—Move Data from Stri ng to String (R|E)SI ← (R|E)SI + 4; (R|E)DI ← (R|E)DI + 4; FI; ELSE (R|E)SI ← (R|E)SI – 4; (R|.
3-672 Vol. 2A MOVS/MOVSB/MOVSW/MOVSD/MOVSQ—Move Data from String to String INSTRUCTION SE T REF ERENCE, A-M Virtual-8086 Mode E xc eptions #GP(0) If a memory operand effe ctive address is outside the CS, DS , ES, FS, or GS segment limit. #SS(0) If a memory oper and effective add ress is outside the S S segment limit.
Vol. 2A 3-673 INSTRUCTION SE T REF ERENCE, A-M MOVSD—Move Scalar Double-Precision Floating-Point Value MO VSD—Mo ve Scalar Double-Pr ecision Floating-Poin t V alue Description Moves a scalar double-precision floating-point value from the source operand (second operand) to the destination operan d (first operand).
3-674 Vol. 2A MOVSD—Move Scalar Double-Precision Floating-Point Value INSTRUCTION SE T REF ERENCE, A-M MOVSD voi d _mm_store_sd (d ouble *p, __m128d a) MOVSD __m128d _mm_store_sd (__m128d a, __m1 28d b) SIMD Floating-Poin t Ex ceptions None.
Vol. 2A 3-675 INSTRUCTION SE T REF ERENCE, A-M MOVSD—Move Scalar Double-Precision Floating-Point Value 64-Bit Mode Exc eptions #SS(0) If a memory a ddress referenc ing the SS segment is in a non- canonical form. #GP(0) If the memory address is in a non-canonical form.
3-676 Vol. 2A MOVSHDUP—Move Packed Single-FP High and Duplicate INSTRUCTION SE T REF ERENCE, A-M MO VSHDUP—Mo ve P ack ed Single-FP High and Duplicate Descripti on The linear address corresponds to the addre ss of the least-significant byte of the referenced memory data.
Vol. 2A 3-677 INSTRUCTION SE T REF ERENCE, A-M MOVSHDUP—Move Packed Single-FP High and Duplicate Operation IF (Source == m128) THEN ( * Load instruction *) xmm1[31:0] = m128[63:32]; xmm1[63:32] = m1.
3-678 Vol. 2A MOVSHDUP—Move Packed Single-FP High and Duplicate INSTRUCTION SE T REF ERENCE, A-M Real Add ress Mode Ex cep tions GP(0) If any part of the operand would lie outside of the effe ctive address space from 0 to 0FFFFH. If memory oper and is not aligned on a 16-byte boundary , regardless of segment.
Vol. 2A 3-679 INSTRUCTION SE T REF ERENCE, A-M MOVSLDUP—Move Packed Single-FP Low and Duplicate MO VSLDUP—Mo ve P ack ed Single-FP Lo w and Duplicate Description The linear address corresponds to the addre ss of the least-significant byte of the referenced memory data.
3-680 Vol. 2A MOVSLDUP—Move Packed Single-FP Low and Duplicate INSTRUCTION SE T REF ERENCE, A-M Operat ion IF (Source == m128) THEN (* Load instruction *) xmm1[31:0] = m128[31:0]; xmm1[63:32] = m128.
Vol. 2A 3-681 INSTRUCTION SE T REF ERENCE, A-M MOVSLDUP—Move Packed Single-FP Low and Duplicate Real Addr ess Mode Exc eptions GP(0) If any part of the operand would lie outside of the effective address space from 0 to 0FFFFH. If memory operand is not aligned on a 16-byte boundary , regardless of segment.
3-682 Vol. 2A MOVSS—Move Scalar Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M MO VSS—Mo ve Scalar Single-Pr ecision Floating-Point V alues Descripti on Moves a scalar single-precision floating-poi nt value from the source operand (second operand) to the destination operand (first oper and).
Vol. 2A 3-683 INSTRUCTION SE T REF ERENCE, A-M MOVSS—Move Scalar Single-Precision Floating-Point Values MOVSS void _mm_store_ss(float * p, __m128 a) MOVSS __m128 _mm_move_ss (__m128 a, __m128 b) SIMD Floating-Point Ex ceptions None.
3-684 Vol. 2A MOVSS—Move Scalar Single-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M 64-Bit Mode Exc eptions #SS(0) If a memory address referencing t he SS segment is in a non- canonical form. #GP(0) If the memory address is in a non-canonical form.
Vol. 2A 3-685 INSTRUCTION SE T REF ERENCE, A-M MOVSX/MOVSXD—Move with Sign-Extension MO VSX/MO VSXD—Mo ve with Sign-Ex tension Description Copies the contents of the source operand (register or me.
3-686 Vol. 2A MOVSX/MOVSXD—Move with Sign-Extension INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #GP(0) If a memory operand effe ctive address is outside the CS, DS , ES, FS, or GS segment limit. If the DS, ES, FS, or GS register contains a NULL segment selector .
Vol. 2A 3-687 INSTRUCTION SE T REF ERENCE, A-M MOVUPD—Move Unaligned Packed Double -Precision Floating-Point Values MO VUPD—Mov e Unaligned Pa ck ed Double-Precision Floating-P oint Va l u e s Des.
3-688 Vol. 2A MOVUPD—Move Unaligned Packed Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M Pro tected Mode Ex ceptions #AC(0) If alignment checking is enabled and an unaligned memory reference is made. #GP(0) For an illegal memory oper and effective address in the CS, DS, ES, FS or GS segm ents.
Vol. 2A 3-689 INSTRUCTION SE T REF ERENCE, A-M MOVUPD—Move Unaligned Packed Double -Precision Floating-Point Values #UD If CR0.EM[bit 2] = 1. If CR4.
3-690 Vol. 2A MOVUPS—Move Unaligned Packed Single-Precision Floating-Point Value s INSTRUCTION SE T REF ERENCE, A-M MO VUPS—Mov e Unaligned Pack ed Single-Precision Floating-P oint Va l u e s Desc.
Vol. 2A 3-691 INSTRUCTION SE T REF ERENCE, A-M MOVUPS—Move Unaligned Packed Si ngle -Precision Floating-Point Values Pr otected Mode Ex ceptions #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made. #GP(0) For an illegal memory operand effective address in the CS, DS, ES, FS or GS segments.
3-692 Vol. 2A MOVUPS—Move Unaligned Packed Single-Precision Floating-Point Value s INSTRUCTION SE T REF ERENCE, A-M #UD I f CR0.EM[bit 2] = 1. If CR4.
Vol. 2A 3-693 INSTRUCTION SE T REF ERENCE, A-M MOVZX—Move with Zero-Ex tend MO VZX —Mov e with Zer o-Extend Description Copies the contents of the source operand (register or memory location) to the desti- nation operand (register) and zero extends the value.
3-694 Vol. 2A MOVZX—Move with Zero-Extend INSTRUCTION SE T REF ERENCE, A-M #SS(0) If a memory oper and effective add ress is outside the S S segment limit. #PF(fault-code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
Vol. 2A 3-695 INSTRUCTION SE T REF ERENCE, A-M MUL—Unsigned Multipl y MUL —Unsigned Multiply Description Performs an unsigned multiplication of the first operand (destination oper and) and the second operand (source operand) and stores the result in the destination operand.
3-696 Vol. 2A MUL—Unsigned Mu ltiply INSTRUCTION SE T REF ERENCE, A-M Operat ion IF (Byte operation) THEN AX ← AL ∗ SRC; ELSE (* Word or doub leword operation *) IF OperandSize = 16 THEN DX:AX .
Vol. 2A 3-697 INSTRUCTION SE T REF ERENCE, A-M MUL—Unsigned Multipl y #SS(0) If a memory operand effective address is outside the SS segment limit. #PF(fault -code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory referen ce is made.
3-698 Vol. 2A MULPD—Multiply Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M MULPD—Multiply Pack ed Double-Precision Floating-P oint V alues Descripti on Performs a .
Vol. 2A 3-699 INSTRUCTION SE T REF ERENCE, A-M MULPD—Multiply Packed Double -P recision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .
3-700 Vol. 2A MULPD—Multiply Packed Double-Precision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .
Vol. 2A 3-701 INSTRUCTION SE T REF ERENCE, A-M MULPS—Multiply Packed Single-Precision Floating-Point Val ues MULPS—Multiply Pack ed Single-Precision Floating-Poin t V alues Description Performs a .
3-702 Vol. 2A MULPS—Multiply Packed Single-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #XM If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating-point exception and CR4.
Vol. 2A 3-703 INSTRUCTION SE T REF ERENCE, A-M MULPS—Multiply Packed Single-Precision Floating-Point Val ues #XM If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 1. #UD If an unmasked SIMD floating -point exception and CR4.
3-704 Vol. 2A MULSD—Multiply Scalar Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M MULSD—Multiply Scalar Double-Pr ecision Floating-Poin t V alues Descripti on Multiplies.
Vol. 2A 3-705 INSTRUCTION SE T REF ERENCE, A-M MULSD—Multiply Scalar Double-Precision Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .
3-706 Vol. 2A MULSD—Multiply Scalar Double-Prec ision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID .
Vol. 2A 3-707 INSTRUCTION SE T REF ERENCE, A-M MULSS—Multiply Scalar Single-P reci sion Floating-Point Values MULSS—Multiply Scalar Single-Pr ecision Floating-Poin t V alues Description Multiplies.
3-708 Vol. 2A MULSS—Multiply Scalar S ingle-P recision Floating-Point Values INSTRUCTION SE T REF ERENCE, A-M #UD If an unmasked SIMD floating-point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4. OSFXSR[bi t 9] = 0. If CPUID.
Vol. 2A 3-709 INSTRUCTION SE T REF ERENCE, A-M MULSS—Multiply Scalar Single-P reci sion Floating-Point Values #UD If an unmasked SIMD floating -point exception and CR4.OSXM- MEXCPT[bit 10] = 0. If CR0.EM[bit 2] = 1. If CR4.OSFXSR[bit 9] = 0. If CPUID .
3-710 Vol. 2A MWAIT—Monitor Wait INSTRUCTION SE T REF ERENCE, A-M MW AIT—Monitor W ait Descripti on MW AIT instruction provides hints to allow the processor to enter an implementation- dependent optimized state. There are two principal targe ted usages: address-range monitor and advanced power managemen t.
Vol. 2A 3-711 INSTRUCTION SE T REF ERENCE, A-M MWAIT—Monitor Wait processor will exit the state and handle the interrupt. If an SMI caused the processor to exit the implementation-dependent-optimized state, execution will resume at the instruction following MWAIT after handling of the SMI.
3-712 Vol. 2A MWAIT—Monitor Wait INSTRUCTION SE T REF ERENCE, A-M Note that if MWAIT is used to enter any of the C -states that are numerically higher than C1, a store to the address range armed by the MONITOR instruction will cause the processor to exit MWAIT only if the store was originated by other processor agents.
Vol. 2A 3-713 INSTRUCTION SE T REF ERENCE, A-M MWAIT—Monitor Wait EDX = 0 (* Hints *) IF ( !trigger_store_happen ed) { MONITOR EAX, ECX, EDX IF ( !trigger_store_happene d ) { MWAIT EAX, ECX } } The .
3-714 Vol. 2A MWAIT—Monitor Wait INSTRUCTION SE T REF ERENCE, A-M Compatibility Mode Exc e p tions Same exceptions as in protected mode. 64-Bit Mode Exc eptions #GP(0) If the linear address of the operand in the CS, DS, ES, FS , or GS segment is in a non-canonical form.
An important point after buying a device Intel 253666-024US (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Intel 253666-024US yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Intel 253666-024US - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Intel 253666-024US you will learn all the available features of the product, as well as information on its operation. The information that you get Intel 253666-024US will certainly help you make a decision on the purchase.
If you already are a holder of Intel 253666-024US, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Intel 253666-024US.
However, one of the most important roles played by the user manual is to help in solving problems with Intel 253666-024US. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Intel 253666-024US along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
