Instruction/ maintenance manual of the product 2200 InSinkErator
Go to page of 15
Inst ant Hot W at er Dispenser Owner ’ s Manual Serie s 22 00 Serie s 1100 Inst allation, Car e & Us e Inst alacion, cuidado & uso Inst allation, soin et utilisation.
Equipment Y ou May Need: W e ar e delighted that you have chosen the InSinkErator ® Instant Hot Water Dispenser to be a part of your home. This unique appliance will save you time and effort in the kitchen, and you’ll enjoy discovering new uses for it each day .
HOW TO USE THIS INSTRUCTION MANUAL Provides a step-by-step narrative describing the installation step, with check boxes that can be marked as you progr ess through the installation. Contains simple illustrations that provide visual instruction to support the narrative.
COMPONENTS IN THIS P ACKAGE SST -FL TR Filter Head 3/8" T ube s (2) Filter Di s charge T ube Filter Cartridge 3/4" S crew s (4) Bra ss Nut / Ferrule / T ube In s ert F-HC1100 F-GN1100 F-HC22.
B Q At tank top, depress r elease ring or gray release tab into quick-connect fitting securing blue 1/4 " tube and gently pull line off tank fitting. Pull white 7/16 " tube and clear 5/16 " tube off fittings. Q If not already equipped, the included snap-connect fitting must be installed.
The wall outlet for your dispenser must have power supplied to it continuously and must be fused. It should not be controlled by the same wall switch that operates your disposer . PREP ARA TION ST AR T HERE PROPER IN S T ALLA TION S HOULD T AKE ABOUT 2-4 HOUR S Q Identify locations for the dispenser faucet, tank and filter .
Property Damage: Do not pinch or b reak copper t ub in g . Do not d i s tort the la s t 1 inch of t ub in g . Q From under the sink, place the semi-circular mounting plate onto the threaded stud. Q Place hex nut onto the threaded stud. Ensure faucet head is at desir ed angle.
A Q Select a spot under the sink to mount tank vertically within reach of both plumbing and electrical connections. The tank should be within 16 " or less of faucet water lines and within 30 " or less of a standard gr ounded outlet.
Property Damage: Do not exten d the copper line s farther than the 16" provi d e d . Personal Injury: Do not locate filter a b o ve an o u tlet or other electrical d evice . In s tall hea d an d b rack et s o that connection s req u ire no s tretchin g , kinkin g or pinchin g of t ub in g .
Scalding Hazard: The fa u cet d i s pen s e s near - b oilin g (212ºF) water which can in s tantly ca us e s cal ds or bu rn s . U s e car e when operatin g thi s appliance . Property Damage: Join remainin g t ub e to col d water su pply only . C Q T ur n on the cold water supply .
Property Damage: T o avoid wa ter damage, replace any loose or split tubing. Periodically inspect the unit for any signs of leakage and immediately remove from service any unit suspected of leaking. Personal Injury: This tank is a non-pressurized tank.
CARE AND USE Electric Shock Hazard: T o prevent electrical shock, disconnect power before servicing unit. Use only a properly grounded and polarized electric outlet. Scalding Hazard: Do not allow water to boil. May result in severe burns. Factory temperature pre-set is 200˚F .
FIL TRA TION INFORMA TION T o reduce the risk associated with ingestion of contaminates due to use with wa ter that is microbiologically unsafe or of unknown quality , do not use with water tha t is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
TROUBLESHOOTING WHA T TO DO Water and steam spits forcefully from spout without turning on the dispenser faucet. Water is not hot. • Unit is boiling. May be normal during initial setup. • The unit is unplugged. • The electric outlet is inoperative.
Inst ant Hot W at er Dispenser Owner ’ s Manual Serie s 22 00 Serie s 1100 The Emers on logo is a trademark and service mark o f Emerson Electric Co. 1.800.5 58.57 00 www .insinkerat or .com © 2007 InSinkEr ator , a division of 44069 REV . A Printed in USA Emerson Electric C o.
An important point after buying a device InSinkErator 2200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought InSinkErator 2200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data InSinkErator 2200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, InSinkErator 2200 you will learn all the available features of the product, as well as information on its operation. The information that you get InSinkErator 2200 will certainly help you make a decision on the purchase.
If you already are a holder of InSinkErator 2200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime InSinkErator 2200.
However, one of the most important roles played by the user manual is to help in solving problems with InSinkErator 2200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device InSinkErator 2200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
