Instruction/ maintenance manual of the product Triumph 7038 American Standard
Go to page of 7
M968868 Rev 1.2 7038 Cer tified to comply with ANSI A112.18.1 Installation Instructions TRIUMPH W idespr ead Lavator y Faucet with Speed C onnect™ Drain Adjustable W rench Screwdriver Channel Locks Recommended tools Tubing Cutter 1 2 1 3 4 6 12 5 SLOT T urn off hot and cold water supplies before beginning.
INST ALL POP-UP DRAIN INSTALL BLACK GASKET 3 2 Install BLACK CONE GASKET (1) onto DRAIN BODY (2) from below. Note: The flat side of the BLACK CONE GASKET (1) must face down. 4 Drop DRAIN BODY (4) through sink drain hole. Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4) .
M968868 Rev 1.2 Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5) .
M968868 Rev 1.2 9 INST ALL HANDLES CHECK DRAIN CONNECTIONS 10 11 12 13 TEST INST ALLED FITTING With HANDLES (1) in OFF position, turn on W A TER SUPPLIES (2) and check all connections for leaks. Remove AERA TOR (3) . Operate both HANDLES (1) to flush water lines thoroughly .
M968868 Rev 1.2 Speed Connect™ Drain Troubleshooting Guide 1 2 Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration.
M968868 Rev 1.2 LOOP TOWARD REAR OF SINK LOOP TOWARD FRONT OF SINK Fig. G. 180˚ LOGO LOGO DRAIN Fig. H. STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper.
M968868 Rev 1.2 TIPS FOR REMOVING YOUR OLD DRAIN: Loosen nuts on P-Trap using channel locks. Suggest spraying nuts with spray lubricant to loosen any corrosion or debris that may have built up. Remove P-Trap half from Tailpiece. Use bucket to catch any residual water in P-trap.
An important point after buying a device American Standard Triumph 7038 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Standard Triumph 7038 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Standard Triumph 7038 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Standard Triumph 7038 you will learn all the available features of the product, as well as information on its operation. The information that you get American Standard Triumph 7038 will certainly help you make a decision on the purchase.
If you already are a holder of American Standard Triumph 7038, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Standard Triumph 7038.
However, one of the most important roles played by the user manual is to help in solving problems with American Standard Triumph 7038. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Standard Triumph 7038 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
