Instruction/ maintenance manual of the product WG068A-F4 Ingersoll-Rand
Go to page of 12
ARO OPERATOR’S MANUAL Tool Products INCLUDING: OPERATION, INSTALLATION & MAINTENANCE SECTION M35 MANUAL 41 Released: 6-1-96 3/4” CAPACITY IMPACT WRENCH Model: WG068A-F4-( ) The ARO WG068A-F4 3.
WARNING LABEL IDENTIFICATION FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. WARNING Always wear eye protection when operating or perform- ing maintenance on this tool.
@35 41 PLACING TOOL IN SERVICE LUBRICATION IRAX No. 50 IRAX No. 100 Always use an air line lubricator with these tools. We recommend the following Filter-Lubricator-Regulator Unit: For USA - IRAX No.
MAINTENANCE SECTION.
PART NUMBER FOR ORDERING PART NUMBER FOR ORDERING 1 2 + 3 + 5 + 6 7 8 9 l 10 11 12 13 l 14 15 16 + 17 4 18 19 + 20 21 + 22 23 24 25 26 + 27 Motor Housing Assembly .............. Trigger Assembly .................. Throttle Valve .................... Throttle Valve Seat .
M35 41 MAINTENANCE SECTION Always wear eye protection when operating or performing maintenance on this tool. Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool.
M35 MAINTENANCE SECTION 41 4. 5. 6. 7. 8. The End Plate Dowel (26) will be free to move when the the Front End Plate (25) clears the Housing. Do not lose it. Remove the Rear End Plate Gasket (20). Slide the Front End Plate and Front Rotor Bearing (27) from the Rotor.
M35 MAINTENANCE SECTION 41 3. Place the Reverse Valve Knob (15) on the end of the Valve and, after applying LoctiteB No. 601 to the Reverse Valve Knob Screw (16), fasten the Knob to the Valve with the Screw. Tighten the Knob Screw to 5 to 6 ft-lb (6.75 to 8.
M35 41 MAINTENANCE SECTION TROUBLESHOOTING GUIDE Double I Probable Cause Low power Motor will not run Tool will not impact Dirty Inlet Bushing or Air Strainer Screen and/or Exhaust Using a suitable cleaning solution, in a well ventilated area, clean Air Strainer Screen, Inlet Silencer Bushing and Exhaust Silencer.
M35 41 NOTES.
M35 41 NOTES.
ARO Part of worldwide Ingersoll-Rand M35 41 PN49999-525.
An important point after buying a device Ingersoll-Rand WG068A-F4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ingersoll-Rand WG068A-F4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ingersoll-Rand WG068A-F4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ingersoll-Rand WG068A-F4 you will learn all the available features of the product, as well as information on its operation. The information that you get Ingersoll-Rand WG068A-F4 will certainly help you make a decision on the purchase.
If you already are a holder of Ingersoll-Rand WG068A-F4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ingersoll-Rand WG068A-F4.
However, one of the most important roles played by the user manual is to help in solving problems with Ingersoll-Rand WG068A-F4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ingersoll-Rand WG068A-F4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
